ZKTeco LF10 User manual

Version: 1.0
Date: June 2019
Quick Start Guide
LF10/20

1
Overview
Display screen
Reset button
USB port
LF10 LF20
Indicators
Keypad
Fingerprint sensor &
Card swiping area
(optional)
AUX
AL-
AL+
NC
COM
NO
BUT
GND
SEN
GND
Exitbutton
Auxiliary input
Alarm
Lock
Sensor
BELL+
BELL- Bell
Wiegandout
GND
WD0
WD1
GND
+12V Powerin
TCP/IP port
Tamper
switch

2
Device Installation
1.4m
1 2
3
①
②
Please insert the cable into the terminal before installation.
①Attach the mounting template sticker to the wall, and drill holes according to
the mounting paper.
②Fix the back plate on the wall using wall mounting screws.Attach the device to
the back plate.
③Fasten the device to the back plate with a security screw.

3
TCP/IP
Alarm Smoke
detector
Lock
Exit button
Door sensor
Reader
PC
Standalone Installation
Door Sensor, Exit Button, Alarm & Bell Connection
Bell
-
+
-+
-+
-+
AUX
AL-
AL+
NC
COM
NO
BUT
GND
SEN
GND
BELL+
BELL-
-
+
-+
Detector power
Smokedetector
Door sensor
Alarm
Alarm power
Exitbutton
Bell
Bell power
USB-disk

4
Lock Relay Connection
The system supports Normally Opened Lock and Normally Closed Lock.
The NO LOCK (normally unlocked when power-on) is connected with 'NO' and
'COM' ports, and the NC LOCK (normally locked when power-on) is connected with
'NC' and 'COM' ports.
Take NC Lock as an example below:
1)Device not sharing power with the lock
2)Device sharing power with the lock
DC 12V
DC 12V
+12V
GND
FR107
AUX
AL-
AL+
NC
COM
NO
BUT
GND
SEN
GND
BELL+
BELL-
NC Lock
DC 12V
+12V
GND
AUX
AL-
AL+
NC
COM
NO
BUT
GND
SEN
GND
BELL+
BELL-
FR107
NC Lock

5
Wiegand Output Connection
Ethernet Connection
Default IP address: 192.168.1.201
Subnet mask: 255.255.255.0
Press M/OK to enter the main menu, and select [COMM.] > [Ethernet] > [IP Address],
input the IP address and click [OK].
IP address: 192.168.1.130
Subnet mask: 255.255.255.0
8
7
6RJ 45
5
4
3
2
1
PC
Note: In LAN, IP addresses of the server (PC) and the device must be in the
same network segment when connecting to computer software.
GND
WD0
WD1
Devices that
support Wiegand
input
The device provides standard Wiegand26 output that can be used as a reader.
Note: Whether it is powered by the access controller or not, it should connect the
GND port with the access controller to ensure stable Wiegand transmission.

6
Quick Start
UserRegistration User Authentication ViewRecords
Verified
User Registration
GND
12V DC
Recommended power supply
1) Ratingof12Vand1.5A
2) To share the power with other devices, use a power supply
with higher current ratings.
Power Connection
When there is no super administrator set in the device, press M/OK to enter the main
menu. After setting the super administrator, the system will request for the
administrator’s verification before entering the menu. For the security purpose, it is
recommended to register a super administrator at the first time you use the device.
Press M/OK to enter the main menu, select [User Mgt.] > [New User] to register a new
user. Settings include entering user ID and name, registering fingerprint, badge
(optional) and password, setting user role and access control role.

7
Verification is successful
User Authentication
Press the fingerprint/enter the password/swipe the card (optional) on the device.
After successful verification, the interface is shown in the figure below.
View Records
View records on the device
Download data by USB-disk
Press to enter the main menu and select [USB Manager] > [Download]. Insert M/OK
the USB-disk into the USB port of the device, and download the attendance data or
user data on the device.
Press M/OK to enter the main menu and select [Attendance Search] to enter the
record query interface. Input the user ID and select the time range, press to M/OK
query.

8
View records on the software
1. Connect the device to the network.
2. Login to the ZKAccess3.5 software.
3. Add the device on the software. Download the device records. Then you can click
[Report] to view the records.
Note: For specific operation of ZKAccess3.5 software, please refer to ZKAccess3.5
Security System User Manual.
Ethernet Settings
Press M/OK to enter the main menu and select [COMM.] > [Ethernet] to set the
network parameters. If the TCP/IP communication of the device is successful, the
icon will be displayed in the upper right corner of the standby interface.
Access Control Settings
Press M/OK to enter the main menu and select enter the access [Access Control] to
control management interface and set relevant parameters of access control.

9
ZK Building, Wuhe Road, Gangtou,
Bantian, Buji Town, Longgang
District, Shenzhen China 518129
Tel: [phone]
Fax: [phone]
www.zkteco.com
Copyright©2019 ZKTECO CO., LTD. All rights reserved.