ZKTeco ProBio User manual

QUICK START GUIDE
ProBio
Version: 1.2
Date: September 2021

1
Safety Precautions
Before installation, please read the following safety precautions for user
safety and to prevent product damage.
Do not install the device in a place subject to direct sun light, humidity, dust
or soot.
Do not place a magnet near the product. Magnetic objects such as magnet,
CRT, TV, monitor or speaker may damage the device.
Do not place the device next to heating equipment.
Do not to let liquid like water, drinks or chemicals leak inside the device.
Do not let children touch the device without supervision.
Do not drop or damage the device.
Do not disassemble, repair or alter the device.
Do not use the device for any purpose other than those specified.
Clean the device often to remove dust on it. In cleaning, do not splash water
on the device but wipe it out with smooth cloth or towel.
Contact your supplier in case of a problem!

2
Cautions on Using Face Recognition Device
1) Recommended Standing Position
a. Recommended Registration and Verification Position
b. Factors Affecting the Preciseness of Verification
For user heights between 1
.5m to 1.8m, it is recommended to
install the device at 1
.15m above ground (may be modified
according to user average height)
.
Recommended Procedure
s (as shown in the left
image):
During registration and verification procedures, the
position of device should
not be changed to
prevent deduction
in verification preciseness. If it is
necessary to move the device, its vertical height
should not be changed.
Non-identical registration and verification
gestures
Non-identical registration and verification
heights
Non-identical registration and verification
distance
s from device
Non-identical registration and verification
distance
s from device

3
2) Registration
a. During registration, it is required to adjust your upper body to fit your eyes into the
green frame on the screen.
b. During verification, it is required to show your face in the center of the screen and fit
your face into the green frame in the screen.
Device Overview

Not all products have fingerprint or card function, the real product
shall prevail.

ProBio
Front Left Side
USB Slot
Reset Button
Touch Screen
Doorbell
Camera
Fingerprint Reader
& Card Reader Area

4
Product Dimensions & Installation

Product Dimensions
Mounting the Device on Wall
Power Conne
7.51 in
(190.8 mm)
3.35 in
(85 mm)
4.05 in
(103 mm)
5.08 in
(129 mm)
2.4 in
(61 mm)
Fix the back plate onto the wall using wall mounting screws.
Insert the device into back plate. Use security screws to fasten
the device to back plate.
Put the mounting template sticker onto the wall, and drill holes
according to the mounting paper.
1.15m

5
Power Connection
Without UPS
With UPS (Optional)
Recommended Power Supply
GND
12V DC
12V DC Adaptor
GND
12V DC
12V DC Adaptor
12V±10%, at least 500mA (12V /3A is standard).
To share the power with other devices, use a power supply with higher
current ratings.

6
Ethernet Connection
LAN Connection
Network Cable Adaptor
Ethernet Cable
Note: The device can be connected to PC directly by Ethernet cable.

7
RS485 Connection
RS485 Fingerprint Reader Connection
DIP Settings
1. There are six DIP switches on the back of RS485 fingerprint reader,
switches 1-4 are for RS485 address, switch 5 is reserved, switch 6 is for
reducing noise on long RS485 cable.
2. If RS485 fingerprint reader is powered from the terminal, the length of
wire should be less than 100 meters or 330 ft.
3. If the cable length is more than 200 meters or 600 ft., the number 6
switch should be ON as below.
RS485 Fingerprint Reader

8
Lock Relay Connection
Device Not Sharing Power with the Lock
COM1 12V DC
GND
GND
Sensor NC1
FR107 Diode
12V DC Adaptor
Normally Closed Lock
Notes:
1. The system supports NO LOCK and NC LOCK. For example the NO
LOCK (normally opened at power on) is connected with 'NO1' and
'COM1' terminals, and the NC LOCK (normally closed at power on) is
connected with 'NC1'and 'COM1' terminals.
2. When electrical lock is connected to the Access Control System, you
must parallel one FR107 diode (equipped in the package) to prevent
the self-inductance EMF from affecting the system.
Do not reverse the polarities.
GND

9
Lock Relay Connection
Device Sharing Power with the Lock
COM1
12V DC
GND
Sensor
NC1
FR107 Diode
Normally Closed Lock
GND
GND