ZKTeco TS1000D User manual

TS200 Series Tripod Turnstile User Manual
Page | 1
User Manual
TS200 Series Tripod Turnstile
Date: December 2021
Doc Version: 1.2
English

TS200 Series Tripod Turnstile User Manual
Page | 1
Table of Contents
1TECHNICAL SPECIFICATIONS.............................................................................................................. 2
2UNPACKING AND TESTING THE TRIPOD TURNSTILE ........................................................................ 3
ARM INSTALLATION ........................................................................................................................................................................................32.1
POWER-ON TEST BEFORE INSTALLATION ......................................................................................................................................................32.2
3EQUIPMENT INSTALLATION ............................................................................................................... 4
INSTALLATION CONDITIONS...........................................................................................................................................................................43.1
CABLING ..........................................................................................................................................................................................................53.2
INSTALLATION .................................................................................................................................................................................................63.3
4CABLE DIAGRAM ................................................................................................................................. 7
CONNECTION DIAGRAM OF THE ACCESS CONTROLLER...............................................................................................................................74.1
DIP SWITCH CONFIGURATION FOR SATT-L-V1.1 ......................................................................................................................................74.2
4.2.1 FUNCTION INTRODUCTION......................................................................................................................................................................... 7
4.2.2 OPENING MODE.............................................................................................................................................................................................. 8
4.2.3 OPENING DURATION ..................................................................................................................................................................................... 8
4.2.4 CONTINUE PASSING FUNCTION................................................................................................................................................................. 8
5EQUIPMENT PRECAUTIONS AND MAINTENANCE ............................................................................. 8
PRECAUTIONS..................................................................................................................................................................................................85.1
MAINTENANCE ................................................................................................................................................................................................95.2
6TROUBLESHOOTING.......................................................................................................................... 10
ATTACHMENT 1 FACTORY SETTINGS ...................................................................................................... 11
ATTACHMENT 2 CONNECTION DIAGRAM OF CONTROL BOARD AND ACCESS CONTROL PANEL....... 12

TS200 Series Tripod Turnstile User Manual
Page | 2
Please read this document carefully before installation and using the device.
1Technical Specifications
Input Voltage
AC 100~120V
/200~240V,
50Hz/60Hz
Arm Length (mm) 580
Operating Environment Indoor and
Outdoor (shelter) Dimension(mm) (Figure 1) L=1200, W=280, H=980
Operating Temperature -28ºC ~ 60ºC Package Size (mm) L=1275, W=370, H=1063
Operating Humidity 5% ~ 85% Flow Rate Max 30 passages/minute
Input Control Signal Dry Contact Rated Power 18 W
Figure 1

TS200 Series Tripod Turnstile User Manual
Page | 3
2Unpacking and Testing the Tripod Turnstile
Arm Installation2.1
In order to prevent the arm from damaging during transportation, the arm will not be initially installed to
the devices.
Installation procedure
Put the arm kit into the hole of cabinet; make sure the screw holes match with mechanism core, then
tighten 3 hex screws, as shown in Figure 2-1.
Figure 2-1
Power-on Test before Installation2.2
1. Please make sure that the power requirements are strictly met to avoid permanent damages to the
unit. Input voltage: AC 100~120V/200~240V.
Note: The tripod turnstile must be connected to the ground (earth).
2. Power on and wait 30s for the tripod turnstile to finish the self-check program.
3. Lift the arms manually, as shown in Figure 2-2.
4. Check whether the tripod turnstile and the LED indicators work properly.
If there is any problem, please contact the supplier.

TS200 Series Tripod Turnstile User Manual
Page | 4
Figure 2-2
3Equipment Installation
Installation Conditions3.1
The equipment must be installed on concrete ground, ensuring that expansion bolts can be secured firmly.
You are suggested to install an assistant framework or fence to form a passageway, as shown in Figure 3-1.
Figure 3-1
Notes:
1. When installing the tripod turnstile against the wall, please reserve a distance of at least 100 mm in
order to open the cover for future adjustment and maintenance.
2. The spare space from the end of the arm shall not be greater than 80 mm (see Figure 3-1).
There is a power
switch in the side
direction of this
power supply.
Earth wiring terminal
Lift upwards

TS200 Series Tripod Turnstile User Manual
Page | 5
3. You are also recommended to set a warning line for card swiping (see Figure 3-2). The warning line
prompts users to swipe cards in a particular area, which would greatly reduce the probability of
equipment failure caused by improper operations.
Figure 3-2
Cabling3.2
There are inlets in the bottom plate for cabling, as shown in Figure 3-3. Units of all data is millimeter.
Power supply and communication wire should go through the inlet. Cable protection covers are
suggested to use if it is surface mounted.
Warning: The tripod turnstile must be connected to the ground (earth); there is wiring interface near the
power switch.
Figure 3-3

TS200 Series Tripod Turnstile User Manual
Page | 6
Installation3.3
Drill holes.
Drill holes according to the locations of holes as shown in Figure 3-3.
Fix the mounting plate to its original position.
Place the mounting plate properly, then apply screw securing glue on the surface and threads of the
expansion bolts, install four expansion bolts to secure the mounting plate, and use a horizontal ruler to
test the levelness of the mounting plate. If the mounting plate is not levelled, adjust it with the gaskets
provided. Note that all the four expansion bolts must be installed properly, as shown in Figure 3-4.
Figure 3-4
Install the turnstile on the mounting plate and tighten the screws. Apply screw securing glue before
using and putting gaskets on the screws to adjust the direction of the turnstile. If the tripod turnstile is
not levelled, you can place gaskets to adjust, as shown in Figure 3-5.
Installation levelness Installation levelness
Figure 3-5

TS200 Series Tripod Turnstile User Manual
Page | 7
4Cable Diagram
Connection Diagram of the Access Controller4.1
Figure 4-1
Note: The lock relay duration of access controller device needs to be set to 1s. Forbidden using electrically
charged objects to connect to the port of Opening Signal Input, otherwise will damage the control board.
DIP Switch Configuration for SATT-L-V1.14.2
Figure 4-2
4.2.1 Function Introduction
No. Function Setting Bit Setting Tips
1&2 Opening Mode
00 (default) Two-way Swipe
10 Left Free, Right Swipe
01 Left Swipe, Right Free
11 Two-way Prohibited
3 Opening Duration 0 10S
1 (default) 5S
4 Continue Passing Function 0 (default) Open
1 Close

TS200 Series Tripod Turnstile User Manual
Page | 8
4.2.2 Opening Mode
Card swiping means that you can open the door only after verification. Free means that you can pass the
door without verification. Prohibited means that you can't pass the door, whether you have permission or
not.
4.2.3 Opening Duration
This function refers to the period of time from opening to closing once the turnstile receives an opening
signal. In the DIP switch, number 3 is used for duration settings. It can be set two different values: 5s or 10s.
4.2.4 Continue Passing Function
With the "Continue Passing" function, the turnstile could remember at most 20 swipes of one card at one
time and allows up to 20 people to pass so they don't have to swipe card each time. This function can be
enabled or disabled with number 4 in the DIP switch.
5Equipment Precautions and Maintenance
Precautions5.1
It is recommended to purchase additional accessories to use the product outdoors.
1) You may install cooling fans for the equipment if the working temperature is often above 50 ºC.
2) The device is rated IP54 waterproof under proper installation. However, its ability to stand in
extreme weather conditions, such as typhoon, is not guaranteed.
3) If the temperature is around or below -30ºC, you are recommended to install a heating plate for
the equipment. You might need to turn the power on multiple times to let the device
automatically heat up through the self-check program.
4) The service life of this equipment may be shortened if it works outdoors in coastal areas or a
region prone to acid rain.
If the power and signal cables are connected properly, this equipment can be immersed under water
at a depth of 250 mm, but it must not be powered on when it is immersed in water.
It is highly recommended to set a warning card-swiping line to remind passers-by to correctly swipe
cards at a reasonable distance from the device to prevent passers-by from being squeezed.
It is recommended to place a warning sign at a conspicuous position, and prompt: "Please swipe
your card outside the warning line and pass in order. Thank you! "

TS200 Series Tripod Turnstile User Manual
Page | 9
The maximum stress tolerance of the tripod turnstile's arms
Please note that the maximum tolerance at the center and the ends of the arm is 80kg and 40kg,
respectively (See Figure 5-1). When the impact force on the tripod turnstile reaches the designed limit, the
arms will break down first to ensure that the body of the equipment is not damaged and the passer-by is
not injured.
Figure 5-1
In case of emergencies
This equipment is designed to drop the arms automatically if there is power failure thus people can pass
freely. Also, there is an interface on the turnstile control board connecting with an emergency switch (J6
Drop Arm) which keeps the tripod turnstile open in case of emergencies. Please lift the arms manually after
at least 6 seconds after power restoration.
Maintenance5.2
Forming maintenance consciousness
The tripod turnstile needs to be maintained regularly and repaired once it is damaged. It is recommended
placing warning signs at conspicuous positions for alerting every passersby to pass carefully and in good
order. Reasonable maintenance consciousness helps to guarantee long-term usage of the tripod turnstile.
Regular maintenance
Cleaning and protection liquid dedicated for stainless steel are recommended to wipe the outer shell of
the equipment regularly. The tripod turnstile used outdoors or in an environment with lots of dust must
be maintained at least once a year, for example, clean up the dust and add appropriate lubricating oil to
the disk wheel. Please note that regular maintenance should only be performed after power-off, as shown
in Figure 5-2.
Maximum Stress Tolerance: 80 kg
Maximum Stress
Tolerance: 40 kg

TS200 Series Tripod Turnstile User Manual
Page | 10
Figure 5-2
6Troubleshooting
Symptom Troubleshooting
The indicator is not lit
when the equipment is
powered on.
It may be caused by the power supply or circuit.
Check whether the connection cable and power cable are damaged, or
whether the wiring is loosed.
The arms of the tripod
turnstile cannot be lifted
manually after the
equipment is powered on.
It may be caused by the problem of related components or drop-arm
solenoid.
Check whether the drop-arm solenoid is operating, and check the working
status of the solenoid, as shown in Figure 5-2.
The tripod turnstile does
not grant an access after
successful authentication.
It may be caused by lack of permission or a circuit problem.
Check whether the user has the permission to pass.
Use a multimeter to check whether the NO and COM ports of the
access control system have a relay signal output.
Short-circuit the ports "K1, GND" and "K2, GND"; if the turnstile is
successfully opened, the controller is not normal. In this case, please
refer to Attachment 2 Connection Diagram of Control board and
Access Control Panel to check the cable connection of the controller.
The turnstile allows people
to continuously passing
one-way side.
Check the turnstile-opening solenoid.
Check if the access controller "Lock driving duration" is set to 1s.
Check whether the turnstile-opening solenoid is operating and check
whether something is stuck at the turnstile-opening solenoid, as
shown in Figure 5-2.
Turnstile-opening Solenoid
Lock Rod
Drop-arm
Solenoid
Position Sensor
Disk Wheel

TS200 Series Tripod Turnstile User Manual
Page | 11
Attachment 1 Factory Settings
No. Function Default
1 Lock Driving Duration 5s
2 Door Sensor None
3 Verification Interval 1s
4 Controller Communication TCP/IP: 192.168.1.201
5 Turnstile Opening Duration 5s
6 Passing Direction Indicator Passing is allowed in both directions
7 Continue Passing Function Disabled
8 Alarm Function Disabled
Note: The Lock Driving Duration is 5 seconds by default. Please set it to 1 second. Do not connect an
electrically charged objects to any ports of Opening Signal Input, otherwise it will damage the control
board.

TS200 Series Tripod Turnstile User Manual
Page | 12
Attachment 2 Connection Diagram of Control Board and
Access Control Panel
Warning: This is a class a product. In a domestic environment, this product may cause radio interference
so that the user may have to take adequate additional measures.