zortrax Inkspire User manual

©2018 Zortrax S.A. All rights reserved. All trade names, logos and trademarks mentioned in the following document are registered trademarks of Zortrax and are subject to legal protection. | www.zortrax.com
06.11.2018
42 31
86 75
Fill the tank with resin. The resin level must fit the
MIN and MAX marks. Install the UV cover back on
the printer.
Transfer the file from Z-SUITE to the printer (via
Wi-Fi/Ethernet or using the USB drive) and start the
printing process.
Once the printing process is finished, wait until the
resin fully drains off of the model. Remove the UV
cover.
*Depending on the size and geometry of the model,
you can use the platform rotating jig from the
Starter Kit to save more liquid resin.
Remove the UV cover. If you haven't calibrated the
platform during the set-up of the printer, carry out
this procedure now.
Leave the platform with the model to air dry and
ensure that the model isn’t exposed to the UV light
until it’s completely dry. Next, remove the model
from the platform by hand or use a spatula. If you
have problems with removing the print, use a
cutting knife.
Immediately put the platform with the model in the
Ultrasonic Cleaner. The model cannot be exposed
to the UV light. Turn on the device. Cleaning time
depends on the size of the model, but it shouldn’t
exceed three minutes. Longer cleaning time causes
the liquid to heat up.
Turn off the Ultrasonic Cleaner and remove the
platform with the model.
Wipe the top and edges of the platform with a
paper towel and unscrew the platform screw (A).
Remove the platform (B). Be careful not to spill the
liquid resin on the printer and its surroundings.
Install the UV cover on the printer.
A
B
min
max
• Wear protective clothing, gloves and glasses during all procedures.
• Prepare paper towels and keep them in your workplace for wiping up liquids.
• Printing and post-processing waste, including empty bottles, failed prints, supports, rafts as well
as paper towels with resin residues should be put in the UV Station or in any source of UV light
before disposal. Uncured resin has to be disposed of in accordance with national and local
regulations concerning hazardous waste.
• Detailed information regarding usage and waste disposal of the liquid detergent utilized to clean
3D prints should be found in the SDS delivered by the producer of the liquid.

A
AB
A
B
©2018 Zortrax S.A. All rights reserved. All trade names, logos and trademarks mentioned in the following document are registered trademarks of Zortrax and are subject to legal protection. | www.zortrax.com
1210 119
1614 1513
Insert the resin filter into the silicone funnel and
put them together in the bottle with resin. Pour the
resin left in the tank through the filter and funnel. If
it’s necessary, use a plastic spatula.
Put the model in the UV Station or in any source of
UV light (e.g. direct sunlight).
*Depending on the type of resin you’ve used for
printing, this step is optional.
Unscrew the two screws that secure the resin tank
and remove them (A). Next, remove the resin tank.
Be careful not to spill the resin (B).
Remove the raft and support structures from your
model.
Turn off the Ultrasonic Cleaner, remove the
platform and leave it to air dry. Once the platform is
dry, install it back in the printer (A) and secure it
with the screw (B).
Clean the LCD screen and the outside of the FEP
film with a soft cloth. Install the resin tank back in
its place (A) and secure it with the two screws (B).
Clean the platform surface with a spatula to
remove the residues of cured resin. Next, put the
platform in the Ultrasonic Cleaner and turn on the
device for about 30-60 seconds.
Clean the resin tank with a paper towel. You can
also use isopropyl alcohol for that purpose. If you
change the color or type of resin, clean the tank in
the Ultrasonic Cleaner.
B
B
A
• Wear protective clothing, gloves and glasses during all procedures.
• Prepare paper towels and keep them in your workplace for wiping up liquids.
• Printing and post-processing waste, including empty bottles, failed prints, supports, rafts as well
as paper towels with resin residues should be put in the UV Station or in any source of UV light
before disposal. Uncured resin has to be disposed of in accordance with national and local
regulations concerning hazardous waste.
• Detailed information regarding usage and waste disposal of the liquid detergent utilized to clean
3D prints should be found in the SDS delivered by the producer of the liquid.