3One data ICS6400-12GT12GS4XS User manual

ICS6400-12GT12GS4XS
Layer 3 Industrial Ethernet Switch
Quick Installation Guide
3onedata Co., Ltd.
Address: 3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District,
Shenzhen
Website: www.3onedata.com
Te l : [phone]
Fax: [phone]
【Package Checklist】
Please check the integrity of package and accessories while
first using the switch.
1.
Industrial Ethernet switch
2.
DIN-Rail mounting attachment
3.
Certification
4.
Warranty card
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【
Product Overview
】
This product is Gigabit and 10Gigabit DIN-Rail layer 3
industrial Ethernet switch. The model is:
ICS6400-12GT12GS4XS (12 Gigabit Copper Ports + 12
Gigabit SFP Slots + 4 10G SFP+ Slots, 12~48VDC
Redundant Power Supply).
【
Panel Design
】
Front view
Top view
Rear View
1. Running indicator (RUN)
2. Alarm indicator (ALM)
3. Power supply indicator (P1-P2)
4. 1000/10GBase-X SFP+ slot (X1-X4)
5. Ethernet port indicator (X1-X4, G1-G24)
6. 100/1000Base-X SFP slot (G5-G8, G13-G16,
G21-G24)
7. Power supply input terminal block
8. Relay alarm output terminal block
9. 10/100/1000Base-T(X) Gigabit RJ45 (G1-G4,
G9-G12, G17-G20)
10. Console port
11. DIP switch
12. Grounding screw
13. DIN-Rail mounting kit
【
Mounting Dimension
】
Unit: mm

Notice Before Mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【
DIN-Rail Mounting
】
Adopt 35mm standard DIN-Rail mounting which is suitable for
most industrial scenes, mounting steps as follows:
Step 1 Check if the DIN-Rail mounting kit is installed firmly.
Step 2 Clip the upper part of the DIN-Rail mounting kit, i.e.
the fixed side, into the DIN rail.
Step 3 Press the lower side of the device and insert the
lower part of DIN-Rail mounting kit (the side with
spring support) into DIN-Rail.
Tips:
The DIN-Rail spring support is a metal sheet that can
move up and down, and there will be a sound after it is
clamped in.
Step 4 Check and confirm the product is firmly installed on
DIN rail, then mounting ends.
【
Disassembling DIN-Rail
】
Step 1 Power off the device.
Step 2 Use a slot type screwdriver or other tools to move
the DIN rail spring support downward; At the same
time, move the lower side of the device outward
and move out the lower part of the DIN rail
mounting kit.
Step 3 Lift the device upward slightly, move out the upper
part of DIN-Rail mounting kit. Disassembling ends.
Notice before power on:
Power ON operation: First insert the power supply
terminal block into the device power supply interface,
then plug the power supply plug contact and power on.
Power OFF operation: First, remove the power plug,
then remove the wiring section of terminal block. Please
pay attention to the above operation sequence.
【
Power Supply Connection
】
The device provides 6-pin 5.08mm pitch power
supply terminal blocks and power supply occupies
the top 4 pins. It supports two independent DC
power supply systems, P1 and P2. The series of
device supports redundant power supply, two
power supply can work at the same time. The
device will still run non-stop when one power supply fails.
Power supply supports anti-reverse connection, which protect
the device from damage but the device cannot be powered on.
The definitions of power pin are shown in the left figure, and
the power input range is 12~48VDC.
【
Relay Connection
】
This device provides 6-pin 5.08mm pitch terminal
blocks, relay occupies the lower 2 pins. Relay
terminals are a set of normally open contacts of
the device alarm relay. They are open circuit in the
state of normal non alarm, closed when any alarm
information occurs. For example, they are closed
when powered off, and send out alarm. The switch supports 1
relay alarm information output that can output power supply
alarm or network abnormality alarm. It can be connected to
alarm light or alarm buzzer or other switching value collecting
devices, which can timely inform operators when the alarm
occurs.
【DIP Switch Settings】
The device provides 4-pin DIP switch for function
setting, in which “ON” is the enabled end. The
definitions of DIP switch are as follows:
DIP
Definition
Operation
1 Restore
Factory
Settings
Set the DIP switch to ON, the device
will root automatically and restore to
factory settings, then turn off the DIP
switch.
2-4
Reserved
—
【
Console Port Connection
】
The device provides 1 program debugging port
based on RS-232 serial port which can conduct
device CLI command management after
connecting to PC. The interface adopts RJ45 port, the RJ45
pin definition as follows:
Pin No.
2
3
5
Pin Definition
TXD
RXD
GND
【
Checking LED Indicator
】
The device provides LED indicators to monitor its operating
status, which has simplified the overall troubleshooting
process. The function of each LED is described in the table
below:
LED
Indicate
Description

RUN
ON
Device is not started or abnormal
Blinking Blinking 1 time per second, system
is running normally
OFF The device is powered off or the
device is abnormal.
ALM
ON
Power supply or port link has alarm
OFF Power supply and port link have no
alarm
P1-P2
ON
Power supply is running normally
OFF
Power supply is disconnected or
running abnormally
X1-X4、
G1-G24
ON
Ethernet port has established a
valid network connection
Blinking
Ethernet port is in an active
network status
OFF
Ethernet port has not established
valid network connection
【
Logging in to WEB Interface
】
This device supports WEB management and configuration.
Computer can access the device via Ethernet interface. The
way of logging in to device’s configuration interface via IE
browser is shown as below:
Step 1 Configure the IP addresses of computer and the
device to the same network segment, and the
network between them can be mutually accessed.
Step 2 Enter device’s IP address in the address bar of the
computer browser.
Step 3 Enter device’s username and password in the login
window as shown below.
Step 4 Click the “login” button. Change the initial password
when logging into the device for the first time, after
that, relog into the device to access the device's
Web interface.
Note:
The default IP address of the device is “192.168.1.254”.
The default username and password of the device is
“admin123”.
If the username or password is lost, user can restore it to
factory settings via device DIP switch or management
software; all modified configurations will be cleared
after restoring to factory settings, so please backup
configuration file in advance.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【
Specification
】
Panel
10Gigabit SFP+ 1000/10GBase-X self-adaptive
SFP+ slot
Gigabit SFP 100/1000Base-X self-adaptive
SFP+ slot
Gigabit copper port 10/100/1000Base-T(X)
self-
adaptive RJ45, automatic
flow control, support full/half
duplex mode, MDI/MDI-X
self-adaption
Console port CLI command management port
(RS-232), RJ45
Alarm interface 6-pin 5.08mm
pitch terminal
blocks, alarm occupies 2 pins,
support 1 relay alarm output
Indicator
Running Indicator, Alarm
Indicator, Power Supply
Indicator, Interface Indicator
Switch Property
Backplane bandwidth
128G
Packet buffer size
12Mbit
MAC address table
16K
Power Supply
Input power supply
12~48VDC redundant power
supply, support anti-reverse
connection
Access terminal block 6-
pin 5.08mm pitch terminal
blocks (power supply occupies 4
pins)
Power Consumption
No-load
15.4W@24VDC
Full-load
30W@24VDC
Working Environment
Working temperature
-40
～
65
℃
Storage temperature
-40~85℃
Working humidity
5%
～
95%(no condensation)
Protection grade
IP30(metal shell)