3One data IES5028G-4GS-8GC User manual

- 1 -
IES5028G-4GS-8GC
Industrial Layer 2 Ethernet Switch
Quick Installation Guide
3onedata Co., Ltd.
Address:
3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Song Bai Road, Nanshan
District, Shenzhen, 518108, China
Website:
www.3onedata.com
Tel:
[phone]
Fax:
[phone]
【Package Checklist】
Please check the integrity of package and accessories while
first using the switch.
1.
Industrial Ethernet switch
2.
Power line x2
3.
Quick installation guide
4.
Serial port line
5.
Rack-mounting lug x2
6.
Foot pad x4
7.
Software installation CD
8.
Warranty card
9.
Certification
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【Product Overview】
The product is managed industrial Ethernet switch. The
model is IES5028G-4GS-8GC (4 Gigabit SFP + 8 Gigabit
combo ports + 16 Gigabit copper ports).
【Panel Design】
Front panel
Rear panel
1. Ethernet port indicator
2. Gigabit Combo port
3. Gigabit Ethernet copper port
4. Gigabit SFP port
5. Console port
6. Device running status indicator
7. Restoring factory setting button
8. Alarm indicator
9. Power indicator (P1/P2)
10. Rack-mounting lug
11. Relay 2 output terminal blocks
12. AC power input (P2)
13. Grounding screw
14. AC power input (P1)
15. Relay 1 output terminal block
【Mounting Dimension】
Unit: mm
Note:
Don't place or install the device in area near water or moist,
keep the relative humidity of the device surrounding between
5%~95% without condensation.
Before power on, first confirm the supported power supply
specification to avoid over-voltage damaging the device.
The device surface temperature is high after running; please
don't directly contact to avoid scalding.
【Rack-mounting】
This product adopts rack-mounting, mounting steps as
below:
Step 1 Select the device mounting position and ensure
enough mounting size is reserved.
Step 2 Adopt 4 bolts to install the mounting lugs in the
device position as figure below.
Step 3 Place the device in the rack; adopt 4 bolts to fix two
sides mounting lugs in the rack.

- 2 -
Step 4 Check and confirm the product is firmly installed on
the rack, then mounting ends.
【Disassembling Device】
Step 1 Power off device.
Step 2 Adopt screw driver to loosen the 4 bolts fixed on
the mounting lugs in the rack.
Step 3 Remove the device away from the rack,
disassembling ends.
【Power Supply Connection】
This device provides 2 AC power supply access
interfaces which come with a switch. The power
supply input range is 100~240VAC/DC.
Note:
Power ON operation: First insert the power supply terminal
block into the device power supply interface, and then plug
the power supply socket and power on.
Power switch “—” means power ON, “O” means power OFF.
Power OFF operation: First, put the powers switch to the "O"
side and then disconnect the power supply. Finally disconnect
the connector between the device and the power cord. Please
notice the operation order above.
【Restoring Default Settings】
RESET is restoring default settings button. Restoring default
settings steps as follows: Press and hold the RESET button,
disconnect the power supply and then power on the device,
wait for about 3~4 seconds to restore the factory settings.
【Relay Connection】
R+ and R- are the relay alarm output
section. They are open circuit in normal non alarm state,
closed when any alarm information occurs. The product
supports 2-way relay alarm output, externally connected to
alarm lights or alarm buzzer or other switching value
collecting device in order to timely notify operators when the
alarm occurs.
【Console Port Connection】
The series products provide 1 program debugging port
based on RS-232 serial port which can conduct device CLI
command management after connecting to PC. It adopts
RJ45 interface, its pin definition is showed as follows:
Pin No.
2
3
5
Definition
TXD
RXD
GND
【Checking LED Indicator】
The series products provide LED indicators to monitor the
device working status with a comprehensive simplified
troubleshooting; the function of each LED is described in the
table as below:
LED
State
Description
P1
ON
Power supply is connected or
running normally
OFF
Power supply is disconnected or
running abnormally
P2
ON
Power supply is connected or
running normally
OFF
Power supply is disconnected or
running abnormally
RUN
Blinking
System is running normally
OFF
System is not running or running
abnormally
ON
System is running abnormally
ALM
ON
Power supply or the port’s link is
alarming.
OFF
Power and the port’s link exist no
alarm
Link
ON
Port connection is active
LED
State
Description
(G1-G28)
Blinking
Data transmitted
OFF
Port connection is not active
【Logging in to WEB Interface】
This device supports WEB management and configuration.
Computer can access the device via Ethernet interface. The
way of logging in to device’s configuration interface via IE
browser is shown as below:
Configure the IP addresses of computer and the
Step 1
device to the same network segment, and the
network between them can be mutually
accessed.
Enter device’s IP address in the address bar of
Step 2
the computer browser.
Enter device’s username and password in the
Step 3
login window as shown below.
Click “OK”button to login to the WEB interface of
Step 4
the device.
Note:
The default IP address of the device is

- 3 -
“192.168.1.254”.
The default username and password of the device is
“admin”.
If the username or password is lost, user can restore it
to factory settings via device DIP switch or
management software; all modified configurations
will be cleared after restoring to factory settings, so
please backup configuration file in advance.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【Specification】
Panel
Gigabit SFP interface
1000Base-SFP
1000M Combo port
10/100/1000Base-T(X) RJ45
or 1000 Base-SFP interface
optional
1000 Base-T(X)
10/100/1000 Base-T(X)
self-adapting RJ45 port,
half/full duplex self-adapting or
compulsive working mode,
support MDI/MDI-X
self-adapting
Console port
CLI command line
management port (RS-232),
RJ45
Alarm interface
5-pin 5.08mm pitch terminal
block (R+/R-), support 2 relay
alarm output
Indicator
Power indicator, system alarm
indicator, device running
status indicator, interface
connection/running status
indicator
Switch property
Backplane bandwidth
56G
Packet buffer size
12Mbit
MAC table size
16K
Power supply
Input power supply
100~240VAC/DC
Access terminal
AC Access terminal:
three-phase socket with
rocker switch, support 2-way
AC power supply input
Power consumption
No-load consumption
10.5W
Full-load consumption
25.3W
Working environment
Working temperature
-40～75℃
Storage temperature
-40～85℃
Working humidity
5%～95% (no condensation)
Protection grade
IP30 (aluminum shell)