3One data ICS5530-16GS8GC6XS-2P220 User manual

ICS5530-16GS8GC6XS-2P220
Industrial Layer 3 Ethernet Switch
Quick Installation Guide
3onedata Co., Ltd.
Address:
3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Song Bai Road, Nanshan
District, Shenzhen, 518108, China
Website:
www.3onedata.com
Tel:
[phone]
Fax:
[phone]
【Package Checklist】
Please check whether the package and accessories are
intact while using the switch for the first time.
1. Industrial Ethernet switch
2. Quick installation guide
3. Power line x2 (AC
products only)
4. Serial port line
5. Rack-mounting lug x2
6. Foot pad x4
7. Software installation CD
8. Warranty card
9. Certification
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【Product Overview】
The product is managed industrial Ethernet switch. The
model is ICS5530-16GS8GC6XS-2P220 (6 10Gigabit SFP
(10 Gigabit/Gigabit self-adaption) + 8 Gigabit Combo + 16
Gigabit SFP).
【Panel Design】
Front panel
Rear panel
1. Ethernet port indicator
2. Gigabit Ethernet SFP
3. 1000M Combo port
4. 10 Gigabit SFP + port (10Gigabit / Gigabit
self-adaption)
5. Console port
6. Power indicator (P1/P2)
7. Alarm indicator
8. Device running status indicator
9. Restoring factory setting button
10. Lugs
11. Relay output terminal blocks
12. AC power input
13. Grounding screw
【Mounting Dimension】
Unit: mm
Notice before mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging
the device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【Rack-mounted】
This product adopts rack-mounting, mounting steps as
below:
Step 1 Select the device mounting location to ensure
enough size.
Step 2 Adopt 4 bolts to install the mounting lugs in the
device position as figure below.

Step 3 Place the device in the rack; adopt 4 bolts to fix
two sides mounting lugs in the rack.
Step 4 Check and confirm the product is mounted firmly
on the rack, mounting ends.
【 】
Step 1 Device power off.
Step 2 Adopt screw driver to loosen the 4 bolts fixed on
the mounting lugs in the rack.
Step 3 Shift out the device from rack, disassembling
ends.
Notice before power on:
Power ON operation: First insert the power supply
terminal block into the device power supply interface,
and then plug the power supply plug contact and
power on.
Power switch “—” means power ON, “O” means
power OFF.
Power OFF operation: First, put the powers switch to
the "O" side and then disconnect the power supply.
Finally disconnect the connector between the device
and the power cord. Please notice the operation order
above.
【Power Supply Connection】
AC power supply
This device provides 2 AC power supply access
interfaces which come with a switch.
Power supply range: 100~240VAC/DC.
【Restore Factory Settings】
RESET is restoring default settings button. Device Restoring
default settings steps as follows: press and hold the RESET
button, power on the device again, wait for about 3~4
seconds to restore the factory settings.
【Relay Connection】
R+ and R- are the relay alarm output
section. They are open circuit in normal
non alarm state, closed when any alarm
information occurs. The product supports 2-way relay alarm
output, externally connected to alarm lights or alarm buzzer
or other switching value collecting device in order to timely
notify operators when the alarm occurs.
【Console Port Connection】
The series products provide 1 program debugging port
based on RS-232 serial port which can conduct device CLI
command management after connecting to PC. The
interface adopts RJ45 port, the RJ45 pin definition as
follows:
Pin No.
2
3
5
Definition
TXD
RXD
GND
【Checking LED Indicator】
The series products provide LED indicators to monitor the
device working status with a comprehensive simplified
troubleshooting; the function of each LED is described in the
table as below:
LED
Indicate
Description
P1
ON
PWR is connected and running
normally
OFF
PWR is disconnected and
running abnormally
P2
ON
PWR is connected and running
normally
OFF
PWR is disconnected and
running abnormally
RUN
Blinking
System runs normally
OFF
The system is not running or
running abnormally
LED
Indicate
Description
ON
System is running abnormally
ALM
ON
Power supply, port link alarm
OFF
Power supply, port link without
alarm
Link
(G1-G24,
X1-X6)
ON
Port has established valid
network connection
Blinking
Port is in a network
communication status
OFF
Port hasn’t established valid
network connection.
【Logging in to WEB Interface】
This device supports WEB management and configuration.
Computer can access the device via Ethernet interface. The
way of logging in to device’s configuration interface via IE
browser is shown as below:
Step 1 Configure the IP addresses of computer and the
device to the same network segment, and the
network between them can be mutually accessed
Step 2 Enter device’s IP address in the address bar of
the computer browser.
Step 3 Enter device’s user name and password in the
login window as shown below.

Step 4 Click “OK” button to login to the WEB interface of
the device.
Notes:
The default IP address of the device is
“192.168.1.254”.
The default username and password of the device is
“admin123”.
If the username or password is lost, user can restore it
to factory settings via device DIP switch or
management software; all modified configurations
will be cleared after restoring to factory settings, so
please backup configuration file in advance.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【Specification】
Panel
10GbE interface
10GbE SFP+ port (10Gigabit /
Gigabit self-adaption)
1000M Combo port
10/100/1000Base-T(X) RJ45
or 1000 Base-SFP interface
optional
Gigabit SFP
1000Base-SFP slot
Console port
CLI command management
port (RS-232), RJ45
Alarm interface
5-pin 5.08mm pitch terminal
block (R+/R-), support 2 relay
alarm output
Indicator
Power indicator, system alarm
indicator, device running
status indicator, interface
connection/running status
indicator
Switch Property
Backplane bandwidth
168G
Packet buffer size
16Mbit
MAC Address Table
16K
Power supply
Input power supply
100~240VAC/DC
Access terminal block
Support single-phase socket
with rocker switch
Power consumption
No-load
21.1W@220VAC
Full-load
37.8W@220VAC
Working Environment
Working temperature
-40~75℃
Storage temperature
-40~85℃
Working humidity
5%～95% (no condensation)
Protection grade
IP40 (metal shell)