3One data IPS7112G-4GS-8GPOE User manual

IPS7112G-4GS-8GPOE
Managed Industrial Ethernet Switch
User manual
Version 1.0.0, Jun. 2017
www.3onedata.com

User manual
1www.3onedata.com
IPS7112G-4GS-8GPOE user manual
Statement
Copyright Notice
Information in this document is reserved by 3onedata Co., Ltd. Reproduction
and extract without permission is prohibited.
Trademarks Notice
, and is registered trademarks of
3onedata Co., Ltd. All other trademarks or registered marks in this manual
belong to their respective manufacturers.
Agreement
As the product version upgrades or other reasons, this document is subject to
change without notice. Unless other agreement, this document only as a
guide to use. All statement, information and suggestion in this document,
without warranty of any kind, either expressed or implied.
Revision History
Version No.
Date
Reason
V1.0.0
Jun, 2017
Document creation
Notes
In reading this manual, please pay attention to the following symbols,
Information necessary to explain
Special attention

User manual
2www.3onedata.com
Content
Chapter 1 Summarize ...........................................................................................................................................................1
1.1 Introduction.................................................................................................................................................................1
1.2 Features......................................................................................................................................................................1
Chapter 2 Hardware Description...........................................................................................................................................2
2.1 Panel Design...............................................................................................................................................................2
2.2 Power Input.................................................................................................................................................................3
2.3 DIP Switch ..................................................................................................................................................................3
2.4 Relay connection.........................................................................................................................................................3
2.5 Console port................................................................................................................................................................3
2.6 Communication port....................................................................................................................................................4
2.7 LED Indicator ..............................................................................................................................................................6
2.8 Installation...................................................................................................................................................................6
Chapter 3 Appearance and Dimension .................................................................................................................................8
3.1 Appearance.................................................................................................................................................................8
3.2 Dimension...................................................................................................................................................................8
Chapter 4 Packing List..........................................................................................................................................................9
Chapter 5 Network Configuration........................................................................................................................................10
5.1 Configure PC‟s IP Address .......................................................................................................................................10
Chapter 6 WEB Management .............................................................................................................................................11
6.1 Configurate preparing ............................................................................................................................................... 11
6.2 System Configuration................................................................................................................................................13
6.2.1 System information ..........................................................................................................................................13
6.2.2 Configuration network........................................................................................................................................15
6.2.3 User configuration..............................................................................................................................................16
6.2.4 Device log message...........................................................................................................................................16
6.2.5 SSHD configuration ...........................................................................................................................................17
6.2.6 Telnet configuration ...........................................................................................................................................18
6.2.7 HTTPS configuration..........................................................................................................................................19
6.2.8 Diagnosis...........................................................................................................................................................19
6.2.8.1 Ping.............................................................................................................................................................19
6.2.8.2 Traceroute ..................................................................................................................................................20
6.2.8.3 Port loopback.............................................................................................................................................. 20
6.3 Port Configuration.....................................................................................................................................................21
6.3.1 Port Settings ......................................................................................................................................................21
6.3.2 Storm control......................................................................................................................................................23
6.3.3 Port rate-limit......................................................................................................................................................25
6.3.4 Mirror..................................................................................................................................................................26

User manual
3www.3onedata.com
6.3.5 Alarm setting......................................................................................................................................................27
6.3.6 PoE configuration...............................................................................................................................................28
6.3.6.1 Global configuration....................................................................................................................................28
6.3.6.2 PoE port configuration ................................................................................................................................29
6.3.7 Port channel configuration .................................................................................................................................29
6.3.7.1 Static configuration .....................................................................................................................................30
6.3.7.2 LACP configuration.....................................................................................................................................31
6.3.8 Isolate-port configuration....................................................................................................................................32
6.3.9 Port statistic .......................................................................................................................................................32
6.3.9.1 Port state ....................................................................................................................................................32
6.3.9.2 Detail port state........................................................................................................................................... 33
6.4 Layer 2 Configuration................................................................................................................................................34
6.4.1 VLAN Configuration...........................................................................................................................................34
6.4.1.1 PVlan configuration.....................................................................................................................................34
6.4.1.2 Trunk configuration.....................................................................................................................................35
6.4.1.3 VLAN configuration.....................................................................................................................................36
6.4.1.4 MAC-VLAN.................................................................................................................................................36
6.4.2 MAC configuration .............................................................................................................................................37
6.4.2.1 MAC configuration ......................................................................................................................................37
6.4.2.2 Static MAC..................................................................................................................................................38
6.4.3 Spanning-tree ....................................................................................................................................................39
6.4.3.1 Bridge setting..............................................................................................................................................39
6.4.3.2 Instance setting...........................................................................................................................................40
6.4.3.3 Bridge port..................................................................................................................................................41
6.4.3.4 Instance port configuration..........................................................................................................................42
6.4.4 IGMP-Snooping .................................................................................................................................................43
6.4.4.1 IGMP-Snooping..........................................................................................................................................43
6.4.4.2 Static Multicast............................................................................................................................................44
6.4.5 SW-Ring.............................................................................................................................................................45
6.4.5.1 Global configuration....................................................................................................................................45
6.4.5.2 Node configuration......................................................................................................................................45
6.4.6 GMRP configuration...........................................................................................................................................49
6.4.6.1 GMRP global configuration.........................................................................................................................49
6.4.6.2 GMRP port configuration ............................................................................................................................50
6.4.6.3 GMRP group...............................................................................................................................................51
6.5 Network security........................................................................................................................................................51
6.5.1 Access control....................................................................................................................................................51
6.5.2 ACL configuration ..............................................................................................................................................52
6.5.2.1 ACL group configuration .............................................................................................................................52
6.5.2.2 Time range configuration ............................................................................................................................52
6.5.2.3 MAC ACL configuration ..............................................................................................................................53
6.5.2.4 IP ACL configuration...................................................................................................................................54
6.5.3 IEEE802.1x configuration...................................................................................................................................56
6.5.3.1 Global configuration....................................................................................................................................56

User manual
4www.3onedata.com
6.5.3.2 Port configuration........................................................................................................................................57
6.6 Advanced configuration.............................................................................................................................................58
6.6.1 QOS configuration .............................................................................................................................................58
6.6.1.1 Global configuration....................................................................................................................................58
6.6.1.2 Port configuration........................................................................................................................................59
6.6.2 LLDP configuration ............................................................................................................................................60
6.6.2.1 Global configuration....................................................................................................................................60
6.6.2.2 Port configuration........................................................................................................................................61
6.6.2.3 LLDP neighbors..........................................................................................................................................62
6.6.3 SNMP configuration...........................................................................................................................................63
6.6.3.1 System information.....................................................................................................................................64
6.6.3.2 View............................................................................................................................................................64
6.6.3.3 Community.................................................................................................................................................. 64
6.6.3.4 V3 User....................................................................................................................................................... 65
6.6.3.5 Trap ............................................................................................................................................................66
6.6.4 RMON configuration ..........................................................................................................................................66
6.6.4.1 Event...........................................................................................................................................................66
6.6.4.2 Statistical ....................................................................................................................................................67
6.6.4.3 History.........................................................................................................................................................68
6.6.4.4 Alarm ..........................................................................................................................................................69
6.6.5 DHCP Server configuration................................................................................................................................70
6.6.5.1 DHCP Server configuration......................................................................................................................... 70
6.6.5.2 DHCP pool configuration ............................................................................................................................70
6.6.5.3 Leases list...................................................................................................................................................71
6.6.5.4 Static leases configuration..........................................................................................................................72
6.6.5.5 Port binding configuration...........................................................................................................................72
6.6.6 DHCP-snooping.................................................................................................................................................73
6.6.6.1 Global configuration....................................................................................................................................73
6.6.6.2 Static binding..............................................................................................................................................74
6.6.7 DNS configuration..............................................................................................................................................75
6.6.8 NTP configuration..............................................................................................................................................76
6.7 System management................................................................................................................................................77
6.7.1 Management File...............................................................................................................................................77
6.7.1.1 View launch configuration...........................................................................................................................77
6.7.1.2 Management file.........................................................................................................................................77
6.7.2 Save...................................................................................................................................................................78
6.7.3 Reboot ...............................................................................................................................................................78
6.7.4 Restore ..............................................................................................................................................................78
6.7.5 Firmware............................................................................................................................................................79
Chapter 7 Repair and Service.............................................................................................................................................80
7.1 Internet Service.........................................................................................................................................................80
7.2 Make a call to our technical office.............................................................................................................................80
7.3 Repair or Replace.....................................................................................................................................................80

User manual
5www.3onedata.com
Appendix 1 Glossary table ..................................................................................................................................................81
Appendix 2 Treatment of common problem ........................................................................................................................83

User manual
1 www.3onedata.com
Chapter 1 Summarize
1.1 Introduction
IPS7112G-4GS-8GPOE is an industrial grade, managed and redundancy Ethernet switch which supports
8 Gigabit PoE Ports and 4 Gigabit SFP slots. It provided some kinds of advanced network managed
function, like as: SW-Ring redundancy ring network, STP/RSTP/MSTP, VLAN, Trunking, 802.1X, SNMP,
LLDP, SSH, Quality of Service, Speed control, port mirroring, fault alarm and firmware upgrade online.
SW-Ring can bring your Ethernet to intelligent redundancy. Standard Industry design, can satisfied every
requirement of the industry scene. All components used industry grade, it takes products high reliability. It
provided wide voltage power supply input.
The switch accorded to CE, FCC standard and Industry grade 4 design requirement, support 2 channel
DC power input and 1 channel relay alarm output, and -40～70℃working temperature, can meet all
kinds of Industrial environment requirement and provide the solution of the economy.
1.2 Features
Support IEEE802.3, IEEE802.3u, IEEE802.3z/ab, IEEE802.3x, IEEE802.1Q, IEEE802.1p,
IEEE802.1W/D, IEEE802.1s, IEEE802.3ad, IEEE802.1X
Support 8 10/100/1000Base-T(X) RJ45 PoE ports and 4 Gigabit SFP slot
SW-Ring ring network patent technology (Fault recovery time<20ms)
Support STP/RSTP/MSTP to enhance network stability
Support IEEE802.1X, HTTPS, and SSH to enhance network security
SupportACL function to enhance flexibility and security of network management
Support static multicast, IGMP Snooping and GMRP
Support Port based VLAN and IEEE 802.1Q VLAN
Support QOS absolutely and opposite priority
Support bandwidth management and storm suppression
Support WEB, SNMP, LLDP and Telnet configuration
Support port mirror and port trunking
Support configuration file up and download
Support redundancy DC power supply(48VDC)
Support 1 channel relay alarm output
Industrial grade 4 design, -40-70℃work temperature
IP40 protection grade, DIN-Rail mounting

User manual
2www.3onedata.com
Chapter 2 Hardware Description
2.1 Panel Design
Vertical view and bottom view Rear view Front view Side view
1. Ground screw
2. Terminal block for relay output
3. Console port
4. Terminal block for power input (PWR1, PWR2)
5. DIP switches
6. DIN-Rail mounting kit
7. System running indicator
8. Relay alarm indicator
9. Power input P1(P2) LED
10. PoE port Link/ACT indicator
11. Ethernet port Link/ACT indicator
12. Gigabit PoE port
13. Gigabit SFP port

User manual
3www.3onedata.com
2.2 Power Input
The switch top panel provided 4 bit power supply input terminal block, support DC input. DC power supply
input supported redundancy function, provided PWR1 and PWR2 power input, can use for single, and can
connect 2 separately power supply system, use 1 pair terminal block connect the device at the same time.
If one of the power systems broke, the device can work un-interruptible. Built-in overcorrect protection,
Reverse connection protection. Voltage input range is 48VDC(terminal block defined as: V1-、V1+、V2-、
V2+).
Important notice:
1. Power ON operation: first of all, insert power cable‟s terminal block into device‟s power port, then insert
power supply plug into power source
2. Power OFF operation: First off all, unpin power plug, then strike the terminal block, please take care of
operation sequence.
2.3 DIP Switch
Top panel provided 4 bits DIP switch to do function configure (ON to enable effective), 1 and 4 keep for
future function. 2 is recovery default factory. 3 is for upgrade. Please power off and power on when you
change the status of DIP switch.
2.4 Relay connection
Relay access terminals in the top panel of the device. Between the two terminal relay, as an open circuit
state in normal non alarm state, when there is any alarm information to the closed state. The two terminal
block connector are used to detect both power failure and port failure. The two wires attached to the Fault
contacts form an open circuit when the device has lost power supply from one of the DC power inputs or
one of the ports is failure.
2.5Console port
This series product provided 1pcs procedure test port based in serial port. It adopts RJ45 interface,
located in top panel, can configure the CLI command through RJ45 to DB9 female cable.

User manual
4www.3onedata.com
2.6 Communication port
10/100/1000BaseT(X) Ethernet port
The pinout define of RJ45 port display as below, connect by UTP or STP. The connect distance is no more
than 100m. 100Mbps is used 120Ωof UTP 5, 10Mbps is used 120Ωof UTP 3 ,4, 5.
RJ 45 port support automatic MDI/MDI-X operation. That can connect the PC, Server, Converter and HUB.
Pin 1, 2, 3, 4, 5, 6, 7, 8 Corresponding connections in MDI. 1→3, 2→6, 3→1, 4→7, 5→8, 6→2, 7→4,
8→5, are used as cross wiring in the MDI-X port of Converter and HUB. In MDI/MDI-X, 100/1000Base-TX
PIN defines is as follows:
PIN
MDI
MDI-X
1
BI_DA+/TX+
BI_DB+/RX+
2
BI_DA-/TX-
BI_DB-/RX-
3
BI_DB+/RX+
BI_DA+/TX+
4
BI_DC+/—
BI_DD+/—
5
BI_DC-/—
BI_DD-/—
6
BI_DB-/RX-
BI_DA-/TX-
7
BI_DD+/—
BI_DC+/—
8
BI_DD-/—
BI_DC-/—
Note：10Base-T/100Base-TX, “TX±”transmit data±, “RX±”receive data±, “—”not use.
10/100Base-T(X) MDI (straight-through cable)
10/100Base-T(X) MDI-X (Cross over cable)
1 8

User manual
5www.3onedata.com
Gigabit MDI (straight-through cable)
Gigabit MDI-X (Cross over cable)
MDI/MDI-X auto connection makes switch easy to use for customers without considering the type of
network cable.
1000Base SFP fiber port
1000BaseSFP optical fiber interface is used SFP optical module communication through optical fiber
transmission, can choice different SFP module according to different transfer distance. Fiber interface
must use for pair, TX port is transmit side, must connect to RX (receive side). The fiber interface support
loss line indicator.
Suppose: If you make your own cable, we suggest labeling the two sides of the same line with the same
letter (A-to-A and B-to-B, shown as below, or A1-to-A2 and B1-to-B2).

User manual
6www.3onedata.com
2.7 LED Indicator
LED indictor light on the front panel of product, the function of each LED is described in the table as
below.
System indication LED
LED
State
Description
P1
ON
Power is being supplied to power input PWR1
OFF
Power is not being supplied to power input PWR1
P2
ON
Power is being supplied to power input PWR2
OFF
Power is not being supplied to power input PWR2
Alarm
ON
When the alarm is enabled, power or the port‟s link is inactive.
OFF
Power and the port‟s link is active, the alarm is disabled.
Run
ON/OFF
System is not running well
Blinking
System is running well
Link/ACT
(1~12)
ON
Port connection is active
Blinking
Data transmitted
OFF
Port connection is not active
POE(1~8)
ON
The PoE device is connected by IEEE802.3af/at standard
OFF
No PoE power output or no PoE connected PoE devices
2.8 Installation
Before installation, confirm that the work environment meet the installation require, including the power
needs and abundant space. Whether it is close to the connection equipment and other equipments are
prepared or not.
1. Avoid in the sunshine, keep away from the heat fountainhead or the area where in intense EMI.
2. Examine the cables and plugs that installation requirements.
3. Examine whether the cables be seemly or not (less than 100m) according to reasonable scheme.
4. Power: support 48VDC power supply
5. Environment: working temperature: -40～70℃
Storage Temperature: -40～85℃
Relative humidity: 5%～95%

User manual
7www.3onedata.com
DIN Rail Installation
In order to use in industrial environments expediently, the product adopt 35mm DIN-Rail installation, the
installation steps as below:
1. Examine the DIN-Rail attachment
2. Examine DIN Rail whether be firm and the position is suitability or not.
3. Insert the top of the DIN-Rail into the slot just below the stiff metal spring.
4. The DIN-Rail attachment unit will snap into place as shown below.
Wiring Requirements
Cable laying need to meet the following requirements,
1. It is needed to check whether the type, quantity and specification of cable match the requirement
before cable laying;
2. It is needed to check the cable is damaged or not, factory records and quality assurance booklet
before cable laying;
3. The required cable specification, quantity, direction and laying position need to match
construction requirements, and cable length depends on actual position;
4. All the cable cannot have break-down and terminal in the middle;
5. Cables should be straight in the hallways and turning;
6. Cable should be straight in the groove, and cannot beyond the groove in case of holding back the
inlet and outlet holes. Cables should be banded and fixed when they are out of the groove;
7. User cable should be separated from the power lines. Cables, power lines and grounding lines
cannot be overlapped and mixed when they are in the same groove road. When cable is too long,
it cannot hold down other cable, but structure in the middle of alignment rack;
8. Pigtail cannot be tied and swerved as less as possible. Swerving radius cannot be too small
(small swerving causes terrible loss of link). Its banding should be moderate, not too tight, and
should be separated from other cables;
9. It should have corresponding simple signal at both sides of the cable for maintaining.

User manual
8www.3onedata.com
Chapter 3 Appearance and Dimension
3.1 Appearance
3.2 Dimension
Unit (mm)

User manual
9www.3onedata.com
Chapter 4 Packing List
Please check the packaging and accessories by your first using. Please inform us or our distributor if your
equipments have been damaged or lost any accessories, we will try our best to satisfy you.
Description
Quantity
Industrial PoE switch
1
User manual
1
Documentation and software CD
1
Warranty card
1
Certificate of quality
1
DIN-Rail mounting kit
1

User manual
10 www.3onedata.com
Chapter 5 Network Configuration
The switch can access, configuration and management through WEB, the user manual will introduce the
operations step by step.
5.1 Configure PC’s IP Address
The switch default address is: 192.168.1.254, subnet mask is: 255.255.255.0. When entering into the
switch Web interface through internet explorer, the IP address of the switch and PC must be in the same
Local Area Network.
You can modify PC's or switch‟s IP address to make sure that they are in the same Local Area
Network. Operating process can follow method 1 or method 2 as below,
Method 1: Modify PC's IP address
Click Start->Control panel->network connections->Local area Connection->Properties->Internet
Protocol (TCP/IP) Setting PC‟s IP address: 192.168.1.X (X is less than 254, from 2 to 253).
Click “OK”, IP address modifies successfully
Method 2: Modify the switch' IP address through Blue_eyes manager software.
Install Blue_eyes manager software on the PC.
Enter into Blue_eyes management interface; click "Search" to search the device.
After searching the device, move mouse to the device, click right key, modify the device's IP address,
Please make sure the device and PC in the same Local Area Network.
This configuration example does not use the Advanced button in the last picture. In one and the same network card
allows the use of multiple IP pseudo-address when use the advanced configuration of the IP address, at which does
not change the original address can still access the switch device. But in the IGMP polling and IEEE 802.1x polling
windows system cannot handle correctly, Unix-like system does not have this problem. The advanced users have to
pay attention to this issue.

User manual
11 www.3onedata.com
Chapter 6 WEB Management
The switch have WEB server inside, can manage and maintenance the device very intuitive through WEB
interface
6.1 Configure preparing
1. The lowest requirement for user's computer is as below:
Install operating system (Windows XP/2000,etc)
Install Ethernet card
Install Web explorer (IE6.0 or higher version)
Install and start TCP/IP protocol
2. The default management IP address of the switch: 192.168.1.254, subnet mask as: 255.255.255.0.
Before access to the configuration interface, the computer's IP address and the switch must be
configured in the same subnet (IP address configuration, please refer to "5.1") if need local configuration;
Computers and switches must be routed reach if for remote configuration.
How to log on to Web Server
Please type in the default IP of switch on the browser‟s address bar, and then will pop-up a window by
clicking the “enter” key which shows you have to enter your user name and password. The default
username and password is “admin”. You can enter your username and password 3 times if you found the
username and password is incorrect. If the 3 input error, the browser will display a "401 Unauthorized"
error message. Refresh the page and then enter the correct user name and password, log on to the Web
Server, it will recommend to modify the user name and password. Please contact our customer service
center if you have more questions.
(Figure 6.1.1)

User manual
12 www.3onedata.com
The default username and password is [admin]，case sensitive for this series. The default password is
with administrator privileges.
Menu Introduction:
Main Menu
Tag
Function
System
Configuration
System information
Can display the system parameters of the switch, such as:
device model, MAC address, etc.
Config network
Display and configuration Device IP address and Gateway
User configuration
Set the user name and password with different permissions
Device log message
The configuration file upload and view device configuration
SSHD-config
Through SSH connection equipment
TELNET-config
Through the Telnet connection configuration
HTTPS-config
WEB interface access
Diagnosis
By Ping, traceroute, port loopback check network
Port
Configuration
Port Settings
Display and configure information of each port: such as
connection status, configuration modes, flow status etc.
Storm control
Set port storm suppression type and flow rate
Port rate-limit
Set port input rate and output rate
Mirror
Set source port and destination port
Alarm setting
Set relay alarm
PoE Config
PoE port power setting
Port channel Config
Static and LACP configuration
Isolate-port Config
Set isolation port
Port statistic
Port data statistics
Layer 2
Configuration
VLAN Configuration
Displays the list of the current VLAN, and the configuration and
management of the VLAN (access, trunk, translate).
Mac-vlan
Configure Mac-vlan parameters
Protocol-vlan
Configure Protocol-vlan parameters
Voice-vlan
Configure Voice-vlan parameters
MAC config
View MAC address learning and setting MAC aging time, static
mac, mac limit config.
Spanning-tree
Set STP, RSTP, MSTP related parameters
IGMP-Snooping
Viewing the multicast address and the setting of static multicast
SW-Ring config
Set ring network type and related parameters
GMRP config
Set the relevant port parameters and view the multicast address
Network
security
Access control
access control
Attack protection
Anti attack setting
ACL config
ACL related configuration, including the group ACL
configuration, time range configuration, IP ACL and MAC ACL
configuration

User manual
13 www.3onedata.com
Main Menu
Tag
Function
802.1x config
802.1X authentication configuration
Advanced
configuration
QOS config
The selection and implementation of QOS scheduling mode
LLDP config
Set to allow the local subnet of network devices to notify their
information
SNMP config
Set SNMP related parameters and view
RMON config
Set Rmon related information configuration and view
DHCP Server config
Set the DHCP address pool and the address or port binding
DHCP-snooping
Set DHCP- snooping related parameters
DNS config
Set the domain name corresponding to the IP
NTP config
Set NTP, time zone and other parameters configuration
System
management
Management File
Switch software upgrade, access, save or restore the
configuration of the switch
Save
Save the current configuration
Reboot
reboot device
Restore
Restore factory settings
Firmware
System upgrade
Web Timeout Treatment
The system timeout will cancel the login if the user did not login for a long time (The configuration of this
login will be remained in the Web interface).
If user doesn't operate the Web interface for a long time, The system will be canceled this login (but configuration
change made in this login will be saved in Web configuration interface.). If the user wants to do any operating on
Web configuration interface again, the system will remind user and returns to the login dialog box. Users need to log
in again if operating is needed. The timeout time is 300s.
6.2 System Configuration
6.2.1 System information
(Figure 6.2.1.1)

User manual
14 www.3onedata.com
Configuration Items
Description
Device Name
Network mark of the device. It is convenient for management tools to judge.
Device Module
The device type.
SN
Serial number of the device. It is convenient for device management.
Hardware Version
Current hardware version.
Firmware Version
Current firmware version.
Running time
Current device usage time
CPU usage
Current device using CPU information
Memory usage
Current devices use memory size information
CPU MAC
Hardware address of the device. It is a unique address which is made up of
hexadecimal number with 48 bits (6 bytes) in length.
Language switching
(Figure 6.2.1.2)
Port information
(Figure 6.2.1.3)