ABB PrimEvo TW220E Manual

INSTRUCTION LEAFLET
EN
—
PrimEvo
TW220E
PLEASE NOTE!
This product must not be modified in any
way. Only original parts should be used
for maintenance.
RPM 311 REV D 8.11.2017
Technical specifications
Power Supply 
Power Consumption 
LED 
Operation Maintained or Non-maintained
Function Manual test
Discharge Duration 
Charge Time 
Battery 
Protection Grade 
Protection Class II
Emergency lumens output 
NI-Mh,3.6V 1.8Ah 2pcs

Only narrow lens has adjustable function.
Adjust the lamp heads and lens direction according corridor pathway as per needs
Open fixture Ceiling Adjust lamp and
head lens
PRECAUTION
Carefully read this instruction leafet before installing
or using the luminaire. This leafet provides important
information about the correct installation, use,
maintenance and disposal of this product. Please
observe the following guidelines:
1. Installation must be in accordance with European

additional local regulations.
2. This product may not be modifed in any way what
so ever or used for a purpose or in an environment
other than for which it is designed. Failling to
observe these guidelines will invalidate the
warranty and the CE-compliance of this product.
3. The luminaire is suitable for indoor use only
4. Before installing the luminaire, the supply must be
isolated.
5. The luminaire must be replaced when it will not
achieve their rated duration.
MOUNTING INSTRUCTIONS
1. Use flat blade screwdriver insert the two slots and
pry off front cover from back plate.
2. Disconnect AC male and female connector.
3. Knock out center and appropriate mounting screw
holes on the back plate.
4. Route AC supply wire through center hole of back
plate.
5. Fix back plate on the mount surface with screw
and anchor nuts.
6. Connect the AC supply wire to terminal block,
reference wiring instruction showed next page.
7. Connect battery connector.
8. Connect AC male and female connector.
9. Snap front cover onto back plate.
10.Restore power and press test button, LED heads
will turn on.
11. Adjust the lamp head and lens direction as
perneeds.
MOUNTING
WALL MOUNTING
Back plate
Front cover
Battery connector
Terminal block
AC male and female connector

Standard EN1838 requirement:
1. Escape route up to 2m wide, 1 lux on the central
axis and 0.5lux at 50% of the width.
2. The ratio of the highest to the lowest illuminance
along the cental axis of the escape route may not
exceed 40:1
Luminaire mounting schematic
EXPLANATIONS
MAINTAINED & NON MAINTAINED FUNCTION
Maintained Operational:
Connect L,N and leave Jump cable connected.
For switchable Maintained Operational:
Connect L,N and remove Jump cable,
Connect switch live to terminal indicated.
Non maintained Operational:
Connect L,N and remove Jump cable
NEUTRAL
SWITCH LIVE
PERMANENT LIVE
JUMP
CABLE
N
L
SL
PHOTOMETRIC
SPACING INFORMATION
Beam angle -C 22° -C90 120°
Lighting distribution
-90°
0°
-60°
-30°
90°
60°
30°
Spacing distance
2m
1m
Central Axis
Spacing Table
Mounting Height (m)
2.5
3.0
7.0 m
7.0 m
14.0 m
14.0 m
TW220E
Distance from wall to first LED luminaire
Distance from one luminaire to another

Ta -0 ° +40°
We reserve the right to make technical
changes or modify the contents of this
document without prior notice. With
regard to purchase orders, the agreed
particulars shall prevail. ABB AG does
not accept any responsibility whatsoever
for potential errors or possible lack of
information in this document.
We reserve all rights in this document
and in the subject matter and illustrations
contained therein. Any reproduction,
disclosure to third parties or utilisation of its
contents – in whole or in parts – is forbidden
without prior written consent of ABB AG.
Copyright© 2017 ABB
All rights reserved
RPM 311 REV E8.11.2017
—
Contact
ABB B.V.
Bruntcliffe Lane
Morley, Leeds
W.Yorkshire LS27 9LL,
United Kingdom
Tel: [phone]
E-Mail: L[email protected]
new.abb.com