ACME MACE User manual

User Manual
www.prolight.co.uk

1A
Contents
1. Safety Instructions .................................................................................................... 2
2. Features..................................................................................................................... 3
3. Technical Specifications ........................................................................................... 3
4. Installation ................................................................................................................ 3
5. Control Panel ............................................................................................................ 4
6. Troubleshooting ........................................................................................................ 5
7. Cleaning And Maintenance ...................................................................................... 5

2A
1. Safety Instructions
Warning
!Please keep this User Guide for future consultation. If you sell the fixture to another user, be
sure that they also receive this instruction booklet.
Cautions:
!All fixtures are intact from the manufacturer, please operate follow up the user manual,
artificial fault are not under guarantee repair.
!Unpack and check carefully there is no transportation damage before using the fixture.
!Be sure that no ventilation slots are blocked, otherwise the fixture will be overheated.
!Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the fixture.
!Use in a dry location.
!It’s important to ground the yellow/green conductor to earth in order to avoid electric shock
(Class 1)
!Maximum ambient temperature is 40°. Don’t operate it where the temperature is higher than
this.
!First run, there will be smoke or smells, and all disappearing a few minutes later.
!Make sure there are no flammable materials close to the fixture while operating, as it is fire
hazard.
!Look over power wires carefully, replace immediately if there is any damage.
!Fixture surface temperature may reach up to 65°. Don’t touch the housing bare-hand during its
operation.
!Never run on for a long time lest shortening lifespan.
!Do not operate in dirty and dusty environment, also cleaning fixtures regularly.
!Do not allow children to operate the fixture.
!Never turn on and off the fixture time after time.
!The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
!Do not open the fixture as there are no user serviceable parts inside. Never try to repair the
fixture by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.
Please contact the nearest authorised technical assistance center.
!Disconnect the mains power if the fixture is not used for a long time.
Please read the instructions carefully which includes important
information about the installation, operation and maintenance.

3A
2. Features
!Great built-in programs triggered by music
!3 balls rotating speed can be adjustable by a knob
!2 Operation Modes: Sound Activation, Automatic selectable via switch
!Low heat, Low power consumption, no duty cycle, runs all the night
!Colour Mix Effect
!Suitable for theaters, studios, retail stores, and other similar locations.
3. Technical Specifications
!Power supply:AC 100V~240V, 50/60Hz
!Power Consumption: 21.4W
!Coverage: 360°
!LED Sources: 6 x 3W RGB LEDs
!Dimension: 313 x 287.5 x 254mm
!Weight: 2.2Kgs
4. Installation
The fixture should be mounted via its screw holes on the bracket. Always ensure that the fixture
is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to
which you are attaching the fixture is secure and is able to support a weight of 10 times of the
fixture’s weight. Also always use a safety cable that can hold 12 times of the weight of the fixture
when installing the fixture.

4A
5. Control Panel
1. Potentiometer Knob: Adjust the rotation speed of the motor:
The speed at which this unit spins can be adjusted by turning the knob. When the knob is turned
all the way counter-clockwise it will spin the slowest at 21 r.p.m. By turning the knob
clockwise you can increase the rate of speed 21 r.p.m. to the fastest rate at 35 r.p.m.
2. Power Switch: Control the mains power On or Off.
3. Power Cable: Connect to the power supply.

5A
6. Troubleshooting
If the fixture does not work, no light, please check the connection of power cable, also measure the
mains voltage on the main connector
7. Cleaning And Maintenance
The cleaning must be carried out periodically to optimize light output. Cleaning frequency depends
on the environment in which the fixture operates: moist, smoky or particularly dirty surrounding
can cause greater accumulation of dirt on the fixture.
!Clean with lint-free cloth using normal glass cleaning liquid.
!Always dry the parts carefully.
!Clean the surface at least every 30 days.
!Never use alcohol or solvents.

6A
Declaration of Conformity
We declare that our products (lighting equipments) comply with the
following specification and bears CE mark in accordance with the
provision of the Electromagnetic Compatibility (EMC) Directive
2004/108/EC.
EN55103-1: 2009 ; EN55103-2: 2009;
EN61000-3-2: 2006 + A1:2009 + A2:2009; EN61000-3-3: 2008.
&
Harmonized Standard
EN 60598-1:2008 + All:2009; EN 60598-2-17:1989 + A2:1991;
EN 62471:2008; EN 62493: 2010
Safety of household and similar electrical appliances
Part 1: General requirements

7A
Innovation, Quality, Performance