ACME CM-150 PAGEANT 150 User manual

PAGEANT 150
CM-150
UserGuide
Professional Entertainment Technology

1A
CONTENTS
1. Safety Instruction......................................................................................................2
2. Technical Specification .............................................................................................3
3. How To Set The Unit.................................................................................................4
3.1 Control panel..........................................................................................................4
3.2 Main Function.........................................................................................................4
3.3 Home Position Adjustment ...................................................................................10
4. How To Control The Unit.........................................................................................11
4.1 Master/Slave Built In Preprogrammed Function...................................................11
4.2 Easy Controller.....................................................................................................11
4.3 DMX Controller.....................................................................................................12
4.4 DMX 512 Configuration........................................................................................13
4.5 DMX512 Connection ............................................................................................19
5. Troubleshooting......................................................................................................20
6. Fixture Cleaning .....................................................................................................21

2A
1. Safety Instruction
WARNING
yPlease keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
yUnpack and check carefully there is no transportation damage before using the unit.
yBefore operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
yIt’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
yThe unit is for indoor use only. Use only in a dry location.
yThe unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces.
Be sure that no ventilation slots are blocked.
yDisconnect main power before replacement or servicing.
yMake sure there are no flammable materials close to the unit while operating as it is fire hazard.
yUse safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always by
taking its base.
yMaximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher than
this.
yUnit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand during its
operation. Turn off the power and allow about 15 minutes for the unit to cool down before replacing or
serving.
yIn the event of serious operating problem, stop using the unit immediately. Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
yDO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
yTo prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
yDO NOT open the unit within five minutes after switching off.
yThe housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Please read carefully this instruction, which includes important information
about the installation, usage and maintenance.

3A
Caution:
There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs
yourself. In the unlikely event your unit may require service, please contact your nearest dealer.
Installation:
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you are
attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight.Also always
use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
The equipment must be fixed by the professionals. And it must be fixed at a place where is out of the
touch of people and has no one pass by or under it.
2. Technical Specification
◇Extremely small, fast and powerful LED moving beam and wash effect.
◇DMX Channels: 1/9/12/14/16/28 channel mode
◇Beam angle: 10°
◇Smooth electronic dimming: 0-100%
◇Electronic strobe with pulse and random effects
◇Optional easy controller CA-8 or CA-9 RTX for instant lighting shows at your fingertips
◇High efficiency, low power consumption
◇Super compact, low weight
Power Supply: AC 100V~240V, 50/60Hz
Fuse: T 6.3A
Power consumption: 105W
Lightsource: 7 x 10W LED
Weight: 5.7Kgs
Dimension: 258X167X304mm

4A
3. How To Set The Unit
3.1 Control panel
Display:
To show the various menus and the selected functions
LED: DMX On DMX input present
MASTER On Master Mode
SLAVE On Slave Mode
SOUND Flashing Sound activation
Button:
MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions
Only for remote control:
Connecting with CA-8/ CA-9RTX to control the unit for Stand by, Function and Mode function.
Mains input:
Connect to power supply.
Mains output:
Connect to supply power to the next unit.
DMX input/output:
For DMX512 link, use 3/5-pin XLR cable to link the unit together.
3.2 Main Function
To select any of the given functions, press the MENU button up to when the required one is showing on
the display. Select the function by ENTER button and the display will blink. Use DOWN and UP button to
change the mode. Once the required mode has been selected, press the ENTER button to setup, to go
back to the functions without any change press the MENU button again. Hold and press the MENU
button about one second or wait for one minute to exit the menu mode.
The main functions are showing below:

5A

6A
DMX Address
Select DMX Address, press the ENTER button to confirm, the present address will blink on the display.
Use the UP and DOWN button to adjust the address from 1to 512. Once the address has been selected,
press the ENTER button to setup, to go back to the functions without any change press the MENU
button again. Hold and press the MENU button about one second or wait for one minute to exit the
menu mode.
Channel Mode
Select Channel Mode, press the ENTER button to confirm, present mode will blink on the display. Use
the DOWN and UP button to select the 1 chan, 9 chan or 12 chan，14 chan or 16 chan or 28 chan
mode. Once the mode has been selected, press the ENTER button to setup, to go back to the functions
without any change press the MENU button again. Hold and press the MENU button about one second
or wait for one minute to exit the menu mode.
Show Mode
Select Show Mode, press the ENTER button to confirm, present mode will blink on the display. Use the
DOWN and UP button to select the Show 1 or Show 2 or Show 3 or Show 4 mode. Once the mode has
been selected, press the ENTER button to setup, to go back to the functions without any change press
the MENU button again. Hold and press the MENU button about one second or wait for one minute to
exit the menu mode.
Dimmer curve
Select Dimmer curve, press the ENTER button to confirm, present mode will blink on the display. Use
the DOWN and UP button to select the Mode1 or Mode 2 or Mode 3 or Mode 4 mode. Once the mode
has been selected, press the ENTER button to setup, to go back to the functions without any change
press the MENU button again. Hold and press the MENU button about one second or wait for one
minute to exit the menu mode.

7A
Mode 1(Optically Linear): The increase in light intensity appears to be linear as DMX value is
increased.
Mode 2(Square Law): Light intensity control is finer at low levels and coarser at high levels.
Mode 3(Inverse Square Law): Light intensity control is coarser at low levels and finger at high levels.
Mode 4(S-cure): Light intensity control is finger at low levels and high levels and coarser at medium
levels.
Slave Mode
Select Slave Mode, press the ENTER button to confirm, present mode will blink on the display. Use the
DOWN and UP button to select the Slave 1 (normal) or Slave 2 (2 light show) mode. Once the mode
has been selected, press the ENTER button to setup, to go back to the functions without any change
press the MENU button again. Hold and press the MENU button about one second or wait for one
minute to exit the menu mode.
Black Out
Select Slave Mode, press the ENTER button to confirm, present mode will blink on the display. Use the
DOWN and UP button to select the Yes (yes blackout) or No (no blackout) mode. Once the mode has
been selected, press the ENTER button to setup, to go back to the functions without any change press
the MENU button again. Hold and press the MENU button about one second or wait for one minute to
exit the menu mode.
Sound State
Select Sound State, press the ENTER button to confirm, present mode will blink on the display. Use the
DOWN and UP button to select the On (sound on) or Off (sound off) mode. Once the mode has been
selected, press the ENTER button to setup, to go back to the functions without any change press the
MENU button again. Hold and press the MENU button about one second or wait for one minute to exit

8A
the menu mode.
Sound Sense
Select Sound Sense, press the ENTER button to confirm, present mode will blink on the display. Use
the DOWN and UP button to change the sound sense from 0…100. Once the mode has been selected,
press the ENTER button to setup, to go back to the functions without any change press the MENU
button again. Hold and press the MENU button about one second or wait for one minute to exit the
menu mode.
Pan Inverse
Select Pan Inverse, press the ENTER button to confirm, present mode will blink on the display. Use the
DOWN and UP button to select the Yes (pan inversion) or No (normal) mode. Once the mode has been
selected, press the ENTER button to setup, to go back to the functions without any change press the
MENU button again. Hold and press the MENU button about one second or wait for one minute to exit
the menu mode.
Tilt Inverse
Select Pan Inverse, press the ENTER button to confirm, present mode will blink on the display. Use the
DOWN and UP button to select the Yes (tilt inversion) or No(normal) mode. Once the mode has been
selected, press the ENTER button to setup, to go back to the functions without any change press the
MENU button again. Hold and press the MENU button about one second or wait for one minute to exit
the menu mode.
Back Light
Select Back Light, press the ENTER button to confirm, present mode will blink on the display. Use the
DOWN and UP button to select the On (Led on) or Off (Led off) mode. Once the mode has been
selected, press the ENTER button to setup, to go back to the functions without any change press the
MENU button again. Hold and press the MENU button about one second or wait for one minute to exit
the menu mode.
Function Delay
Select Function Delay, press ENTER button to confirm, present mode will blink on the display. Use
DOWN and UP button to select the No Delay or 1S/2S/3S Delay (Wait for 1/2/3 seconds before these

9A
Functions of 9/16/28CH are activated/deactivated) mode. Once the mode has been selected, press the
ENTER button to setup, to go back to the functions without any change press the MENU button again.
Hold and press the MENU button about one second or wait for one minute to exit the menu mode.
White Balance
Select White Balance, press the ENTER button to confirm, present mode will blink on the display. Use
the DOWN and UP button to select the Red or Green or Blue. Once the mode has been selected, press
the ENTER button to setup, use the DOWN and UP button to change the value (125~255). Once the
mode has been selected, press the ENTER button to setup, go back to the functions without any change
press the MENU button again. Hold and press the MENU button about one second or wait for one
minute to exit the menu mode.
Manu Test
Select Manu Test, press the ENTER button to confirm, present mode will blink on the display. Use the
DOWN and UP button to select the Pan/ Tilt/ Red1/ Green1/ Blue1/ White1/…Red4/ Green4/ Blue4/
White4/ Dimmer or Strobe. Once the mode has been selected, press the ENTER button to setup, use
the DOWN and UP button to change the value (0~255). Once the mode has been selected, press the
ENTER button to setup, go back to the functions without any change press the MENU button again.
Hold and press the MENU button about one second or wait for one minute to exit the menu mode.
Auto-Test
Press the MENU button up to when the Auto-Test is blinking on the display. Pressing ENTER button
and the unit will run self-test by built-in program. To go back to the functions press the MENU button
again. Hold and press the MENU button about one second or wait for one minute to exit the menu
mode.
Temperature
Press the MENU button up to when the Temperature Test is blinking on the display. Pressing ENTER
button and the display will show the temperature of the unit. To go back to the functions press the MENU
button again. Hold and press the MENU button about one second or wait for one minute to exit the
menu mode.