ACME TV LIGHT PANEL 2000 User manual

CONTENTS
1. Safety Instructions ......................................................................................... 2
2. Technical Specifications ................................................................................. 4
3 Control Panel .................................................................................................. 5
4. The Plate for Barn Door Installation............................................................... 6
5. How To Set The Unit....................................................................................... 6
5.1 Main Function.......................................................................................... 6
6. Control By Universal DMX Controller ........................................................... 11
6.1 DMX512 Connection.............................................................................. 11
6.2 Address Setting ...................................................................................... 12
6.3 DMX512 Configuration........................................................................... 12
7. Troubleshooting........................................................................................... 14
8. Fixture Cleaning ........................................................................................... 14
1D

1. Safety Instructions
WARNING
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction manual.
Important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer will
not accept liability for any resulting defects or problems.
Unpack and check carefully that there is no transportation damage before using the unit.
This product is for indoor use only. Use only in a dry location.
DO install and operate by qualified operator.
DO NOT allow children to operate the fixture.
Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head only.
The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces.
Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.
Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
Minimum ambient temperature TA: 0℃. Maximum ambient temperature TA: 40℃.
DO NOT connect the device to any dimmer pack.
Make sure there are no flammable materials close to the unit while operating to avoid fire
hazard.
Examine the power wires carefully; replace them immediately if there is any damage.
Avoid any inflammable liquids, water or metal objects entering the unit. Once it happens, cut
off the mains power immediately.
DO NOT operate in dirty or dusty environment, do clean fixtures regularly.
DO NOT touch any wire during operation as there might be a hazard of electric shock.
Avoid power wires together twist other cables.
Please read the instruction carefully which includes important information about
the installation, usage and maintenance.
2D

Disconnect mains power before fuse replacement or servicing.
Replace fuse only with the same type.
In the event of serious operating problem, stop using the unit immediately.
Never turn on and off the unit time after time.
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
DO NOT open the unit as there are no user serviceable parts inside.
Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance center if
needed.
Disconnect the mains power if the fixture is has not been used for a long time.
DO use the original packing materials before transporting it again.
DO NOT look directly at the light while the LED is on.
DO NOT start on the unit without LED enclosure or when housing is damaged.
Installation:
The fixture should be mounted via its Omega Quick Release Clamp bracket. Always ensure that the
unit is firmly fixed to avoid vibration and slipping while operating and make sure that the structure
to which you are attaching the unit is secure and is able to support a weight of 10 times of the
fixtures weight. Always use a safety cable that can hold 12 times of the weight of the fixture when
installing.
The equipment must be installed by professionals. It must be installed in a place where is out of the
reach of people and no one can pass by or under it.
3D

2. Technical Specifications
Power Voltage:
AC 100~240V, 50/60Hz
Power Consumption:
210W
Light Source:
480pcs 0.5W CW LED (CW)
480pcs 0.5W WW LED (WW)
Color Temperature:
5600±250K (CW)
3200±150K (WW)
Beam Angle:
110°
Optical:
CRI: CW≥94, WW≥95
CQS: CW≥94, WW≥94
TLCI: CW≥95, WW≥95
Control:
DMX Channel: 1/2A/2B/3 Channels
Control Mode: DMX, Primary/Secondary, Art-Net
Firmware Upgrade: Update via DMX link
Construction:
Display: LCD display
Data In/Out: 5-pin XLR (3-pin XLR is optional)
Power In/Out: Power Connector in
Protection Rating: IP20
Features:
With outstanding floodlight and soft light, TV LIGHT PANEL 2000 are widely applied to photographic
studio, TV station, conference room, shopping mall; Access to buttery.
4D

Dimension/Weight:
668x148x491mm, 13kgs
26.3"x5.8"x19.3"in, 28.7lbs
Photometrics Diagram:
3 Control Panel
1. Display: To show the various menus and the selected function
2. Button:
MENU
To enter into move backward or leave the menu
UP
To go backward to move up in the menu
DOWN
To go forward to move down in the menu
ENTER
To perform the desired functions
5D

3. DIMMER: Adjust the dimmer
4. FUSE(T 5A): Protects the unit from over-voltage or short circuit
5. MAINS IN: To connect to supply power
6. BATTERY (DC 48V): Connects to external battery
7. DMX OUT: Use 5-pin XLR cable to link the next units (3-pin XLR is optional)
8. DMX IN: Use 5-pin XLR cable to link the unit and DMX controller (3-pin XLR is optional)
9. ETHERNET: Transfers fixture’s information to a main controller
4. The Plate for Barn Door Installation
At first, please push the barn door by hand.
Screw
Secondly, please put the Barn Door into the unit, to fasten the screws of the slot, then finish the
barn door installation.
5. How To Set The Unit
5.1 Main Function
Turn on the unit, press the MENU button into menu mode, and press the UP/DOWN button until
the required function is shown on the monitor. Select the function by the ENTER button. Use the
UP/DOWN button to choose the submenu, press the ENTER button to store and automatically
return to the last menu. Press the MENU button or let the unit idle 30 seconds to exit menu mode.
The main functions are shown below:
6D

7D

DMX Setting
To select DMX Setting, press the ENTER button to confirm, use the UP/DOWN button to select
DMX Address, Art-Net Setup or Channel Mode.
DMX Address
To select DMX Address, press the ENTER button to confirm. Use the UP/DOWN button to adjust the
address from 001 to 512, press the ENTER button to store. Press the MENU button back to the last
menu or let the unit idle 30 seconds to exit menu mode.
Art-Net Setup
To select Art-Net Setup, press the ENTER button to confirm. Use the UP/DOWN button to select
Ethernet IP Setup or Art-Net Port Setup, press the ENTER button to store. Press the MENU button
back to the last menu or let the unit idle 30 seconds to exit menu mode.
Channel Mode
To select Channel Mode, press the ENTER button to confirm. Use the UP/DOWN button to select 1
CH, 2A CH, 2B CH or 3 CH, press the ENTER button to store. Press the MENU button back to the last
menu or let the unit idle 30 seconds to exit menu mode.
Dimmer Speed
To select Dimmer Speed, press the ENTER button to confirm. Use the UP/DOWN button to select
Smooth or Fast, press the ENTER button to store. Press the MENU button back to the last menu or
let the unit idle 30 seconds to exit menu mode.
Dimmer Curve Setting
To select Dimmer Curve Setting, press the ENTER button to confirm. Use the UP/DOWN button to
select Linear Curve, Sq. Law Curve, Invert Sq. Law Curve or S Curve, press the ENTER button to
store. Press the MENU button back to the last menu or let the unit idle 30 seconds to exit menu
mode.
8D

Optically Linear: The increase in light intensity appears to be linear as DMX value is increased.
Square Law:Light intensity control is finer at low levels and coarser at high levels.
Inverse Square Law: Light intensity control is coarser at low levels and finger at high levels.
S-Curve: Light intensity control is finger at low levels and high levels and coarser at medium levels.
Pri./Sec. Mode
To select Pri./Sec. Mode, press the ENTER button to confirm. Use the UP/DOWN button to select
Primary or Secondary, press the ENTER button to store. Press the MENU button back to the last
menu or let the unit idle 30 seconds to exit menu mode.
DMX Last State
To select DMX Last State, press the ENTER button to confirm. Use the UP/DOWN button to select
Pri.Sec., Blackout or Hold, press the ENTER button to store. Press the MENU button back to the last
menu or let the unit idle 30 seconds to exit menu mode.
Frequency
To select Frequency, press the ENTER button to confirm. Use the UP/DOWN button to select 900hz,
1000hz, 1100hz, 1200hz, 1300hz, 1400hz, 1500hz, 2500hz, 4000hz, 5000hz, 10000hz, 15000hz,
20000hz or 25000hz, press the ENTER button to store. Press the MENU button back to the last
menu or let the unit idle 30 seconds to exit menu mode.
Display Setting
To select Display Setting, press the ENTER button to confirm, use the UP/DOWN button to select
Contrast Ratio, Backlight Auto Off, Invert Display or Language.
Contrast Ratio
Select Contrast Ratio, press the ENTER button to confirm, present mode will blink on the display,
use the UP/DOWN button to adjust the contrast ratio from 1to 30, press the ENTER button to store.
Press the MENU button back to the last menu or let the unit idle 30 seconds to exit menu mode.
9D

Backlight Auto Off
Select Backlight Auto Off, press the ENTER button to confirm, present mode will blink on the display,
use the UP/DOWN button to select No or Yes, press the ENTER button to store. Press the MENU
button back to the last menu or let the unit idle 30 seconds to exit menu mode.
Invert Display
Select Invert Display, press the ENTER button to confirm, present mode will blink on the display, use
the UP/DOWN button to select No (normal display) or Yes (invert display), press the ENTER button
to store. Press the MENU button back to the last menu or let the unit idle 30 seconds to exit menu
mode.
Language
Select Language, press the ENTER button to confirm, present mode will blink on the display, use the
UP/DOWN button to select English or Chinese, press the ENTER button to store. Press the MENU
button back to the last menu or let the unit idle 30 seconds to exit menu mode.
Manual Mode
To select Manual Mode, press the ENTER button to confirm. Use the UP/DOWN button to select
Dimmer, press the ENTER button to store. Use the UP/DOWN button to adjust the value from 0to
255, press the ENTER button to store. Press the MENU button back to the last menu or let the unit
idle 30 seconds to exit menu mode.
Fixture Information
To select Fixture Information, press the ENTER button to confirm, use the UP/DOWN button to
select Fixture Time or Firmware Version.
Fixture Time
Select Fixture Time, press the ENTER button to confirm, fixture use time will show on the display,
press the MENU button to exit.
Firmware Version
Select Firmware Version, press the ENTER button to confirm, firmware version will show on the
display, press the MENU button back to exit.
10D

Factory Setting
Select Factory Setting, press the ENTER button to confirm, use the UP/DOWN button to select
No(normal) or Yes(the fixture will reset to factory settings), press ENTER button to store. Press the
MENU button to exit.
6. Control By Universal DMX Controller
6.1 DMX512 Connection
1. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120-o h m 1/4 W
resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output
of the last unit.
2. Connect the unit together in a “daisy chain” by XLR plug cable from the output of the unit to
the input of the next unit. The cable cannot be branched or split to a “Y” cable. DMX 512 is a very
high-speed signal. Inadequate or damaged cables, soldered joints or corroded connectors can easily
distort the signal and shut down the system.
3. The DMX output and input connectors are pass-through to maintain the DMX circuit, when one
of the units’ power is disconnected.
4. Each lighting unit needs to have a DMX address to receive the data by the controller. The
address number is between 1-512.
5. The end of the DMX 512 system should be terminated to reduce signal errors.
6. 3 pin XLR connectors are more popular than 5 pins XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+), Pin4, Pin5 not used.
11D

6.2 Address Setting
If you use a universal DMX controller to control the units, you have to set DMX address from 1 to
512 so that the units can receive DMX signal.
Press the MENU button to enter menu mode, select DMX Setting, press the ENTER button to
confirm, use the UP/DOWN button to select DMX Address, press the ENTER button to confirm, the
present address will blinking the display, use the UP/DOWN button to adjust the address from 001
to 512, press the ENTER button to store. Press the MENU button back to the last menu or let the
unit idle 30 seconds to exit menu mode.
Please refer to the following diagram to address your DMX512 channel for the first 4 units.
Channel mode
Unit 1
Address
Unit 2
Address
Unit 3
Address
Unit 4
Address
1 channels 1 2 3 4
2A channels 1 3 5 7
2B channels 1 3 5 7
3 channels 1 4 7 10
6.3 DMX512 Configuration
Please refer to below configurations to control the fixtures
Attentions:
1. The unit will maintain the last condition until reset if you cut-off the DMX signal.
2. For the channel Function, keep the value for about 3 seconds, then the corresponding function
will take into effect.
1 Channels (Mode 1):
CHANNEL VALUE FUNCTION
1
000-255
DIMMER
0%

100%
12D

2A Channels (Mode 2):
CHANNEL VALUE FUNCTION
1
000-255
DIMMER
0

100%
2
000-031
032-063
064-095
096-127
128-159
160-191
192-223
224-255
STROBE
Off
On
Strobe: Slow to Fast
On
Strobe Pulse: Fast to Slow
On
Random Strobe
On
2B Channels (Mode 3):
CHANNEL VALUE FUNCTION
1
000-255
DIMMER
0%

100%
2 000-255 DIMMER FINE
3 Channels (Mode 4):
CHANNEL VALUE FUNCTION
1
000-255
DIMMER
0%

100%
2 000-255 DIMMER FINE
3
000-031
032-063
064-095
096-127
128-159
160-191
192-223
224-255
STROBE
Off
On
Strobe: Slow to Fast
On
Strobe Pulse: Fast to Slow
On
Random Strobe
On
13D

7. Troubleshooting
Following are a few common problems that may occur during operation. Here are some
suggestions for easy troubleshooting:
A. The unit does not work and no light
1. Check the connect power and main fuse.
2. Measure the mains voltage on the main connector.
3. Check the power on LED to see if it can be light up or not.
B. Not responding to DMX controller
1. Check DMX connectors, cables to see if they are linked properly.
2. Check the address settings and DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the
unit or the previous one.
4. Try to use another DMX controller.
5. Check to see if the DMX cables run near or run alongside to high voltage cables that may cause
damage or interference to DMX interface circuit.
C. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.
8. Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically
to optimize light output. Cleaning frequency depends on the environment in which the fixture
operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on
the unit’s optics.
Clean with soft cloth and use normal glass to clean liquid.
Always dry the parts carefully.
Clean the external optics at least every 20 days.
14D

Declaration of Conformity
We declare that our products (lighting equipments) comply with the
following specification and bears CE mark in accordance with the provision
of the Electromagnetic Compatibility (EMC) Directive 2014/3 0/EU.
EN 55032: 2015; EN 55103-2: 2009;
EN 61000-3-2: 2014; EN 61000-3-3: 2013.
&
Harmonized Standard
EN 60598-2-17: 1989+A2: 1991; EN 60598-1: 2015; EN 62471: 2008;
EN 62493: 2015; EN 62031: 2008+A1: 2013+A2: 2015.
Safety of household and similar electrical appliances
Part 1: General requirements
Innovation, Quality, Performance