ACME LED-MS600 PE User manual

LED-MS600 PE
UserGuide
Professional Entertainment Technology
1-
TABLE OF CONTENTS
1. Safety Instruction
2. Technical Specification
3. How To Set The Unit
4. How To Control The Unit
5. DMX 512 Configuration
6. DMX 512 Connection
7. Troubleshooting
8. Fixture Cleaning

2-
1. Safety Instruction
WARNING
Please keep this User Guide for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the
unit.
Before operating, ensure that the voltage and frequency of power supply match
the power requirements of the unit.
It’s important to ground the yellow/green conductor to earth in order to avoid
electric shock.
The unit is for indoor use only. Use only in a dry location.
The unit must be installed in a location with adequate ventilation, at least 50cm
from adjacent surfaces. Be sure that no ventilation slots are blocked.
Disconnect main power before replacement or servicing.
Make sure there are no flammable materials close to the unit while operating as
it is fire hazard.
Use safety cable when fixes this unit.
Maximum ambient temperature is TA: 40℃. Don’t operate it where the
temperature is higher than this.
Unit surface temperature may reach up to 85℃. Don’t touch the housing
bare-hand during its operation. Turn off the power and allow about 15 minutes for
the unit to cool down before replacing or serving.
In the event of serious operating problem, stop using the unit immediately. Never
try to repair the unit by yourself. Repairs carried out by unskilled people can lead
to damage or malfunction. Please contact the nearest authorized technical
assistance center. Always use the same type spare parts.
Do not touch any wire during operation as high voltage might be causing electric
shock.
Warning
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to
rain or moisture.
Please read carefully the instruction, which includes important
information about the installation, usage and maintenance.
3-
Do not open the unit within five minutes after switching off.
The housing, the lenses must be replaced if they are visibly damaged.
Caution
There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact your nearest dealer.
Installation
The unit should be mounted via its metal hole on the bracket. Always ensure that
the unit is firmly fixed to avoid vibration and slipping while operating. Always
ensure that the structure to which you are attaching the unit is secure and is able
to support a 10 times weight of the unit. Also always use a safety cable that can
hold 12 times of the weight of the unit when installing the fixture.
Be sure to locate the unit in a place away from flammable objects at least 15CM
and at least 1M from adjacent surfaces.
Note: the range of mounting height is 0~30 meters.
2. Technical Specification
DMX Channels: 17 channels
3 operation modes: DMX, Master/Slave, SoundActive
Great built-in lighting shows under Master/Slave mode triggered by music
Smooth 0~100% dimming and variable strobe speeds
Motorized focus by DMX control
Automatic Pan/Tilt position correction
Excellent ventilation, ensuring reliable operation
Voltage：AC 100-240V~50/60Hz
Power consumption:280W
Light Source: 1 x150W LED
Beam angel: 17°
Fuse: 6.3A
Dimension: 435.2 x 343.6 x 526.3 mm
Weight: 17kgs

4-
3. How To Set The Unit
3.1 Control Panel
Frontview Rearview
① Display:
To show the various menus and the selected functions
② LED:
DMX On DMX input present
MASTER On Master Mode
SLAVE On Slave Mode
SOUND Flashing Sound activation
③ Button:
MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions
④ DMX input/output:
For DMX512 link, use 3/5-pin XLR plug cable to link the unit together.
⑤ Fuse(6.3A):
Protect the unit from damage of overcurrent.
⑥ Mains input:
Connect to supply mains power.
⑦ Mains output:
Connect to supply mains power for the next unit.
5-
3.2 Power On Display
Every time you turn on the unit, it will run built-in program to reset all motors to
their home position, the display will show as followings, you may hear some noises
for about 20 seconds. It will show warning sign if it goes wrong during resetting and
you can press the MENU button to view the error information.After that the unit will
be ready to receive DMX signal and the display will show it:
Explanation:
001 Show start address
Md.1 17Ch. Show channel mode is mode 1 (17channels mode)
Base 30°C Show temperature of base is 30°C
Lamp 29°C Show temperature of lamp is 29°C
3.3 Main Function
To select any of the given functions, press the MENU button up to when the
required one is showing on the display. Select the function by ENTER button and
the display will blink. Use DOWN and UP button to change the mode. Once the
required mode has been selected, Press ENTER button to store. Back to the main
functions without any change press the MENU button or wait for 8 seconds.
Hold MENU button to quit menu mode, the unit will run the built-in program you
selected.
The main functions are shown below:

6- 7-
DMX Functions
Enter menu mode, select DMX Functions, press ENTER button to confirm, use
UP/DOWN button to select DMX Address or View DMX Value.
DMX Address—DMX512 address setting
Select DMX Address, press ENTER button to confirm, the present address
will blink on the display, use UP/DOWN button to adjust the address from 0 to
512, press ENTER button to store. Press MENU button back to the last menu
or let the unit idle one minute to exit menu mode.
View DMX Value
Select View DMX Value, press ENTER button to confirm. Channel function
and its value will show on the display, use UP/DOWN button to view other
DMX value. Press MENU button back to the last menu or let the unit idle one
minute to exit menu mode.
Fixture Settings
Enter menu mode, select Fixture Settings, press ENTER button to confirm, use
UP/DOWN button to select Pan Inverse, Tilt Inverse, P/T Feedback, Iris Inverse,
BL.O. P/T Moving, BL.O. Color Change, BL.O. Gobo Change.
Pan Inverse
Select Pan Inverse, press ENTER button to confirm, present mode will blink
on the display, use UP/DOWN button to select No (normal) or Yes (pan
inverse), press ENTER button to store. Press MENU button back to the last
menu or let the unit idle one minute to exit menu mode.
Tilt Inverse
Select Tilt Inverse, press ENTER button to confirm, present mode will blink
on the display, use UP/DOWN button to select No (normal) or Yes (tilt inverse),
press ENTER button to store. Press MENU button back to the last menu or let
the unit idle one minute to exit menu mode.

8-
P/T Feedback — pan/tilt Feedback
Select P/T Feedback, press ENTER button to confirm, present mode will
blink on the display, press UP/DOWN button to select No (Pan or tilt’s position
will not feedback while out of step.) or Yes (Feedback while pan/tilt out of
step. ), press ENTER button to store. Press MENU button back to the last
menu or let the unit idle one minute to exit menu mode.
Iris Inverse
Select Iris Inverse, press ENTER button to confirm, present mode will blink
on the display, use UP/DOWN button to select No (normal) or Yes (iris
inverse), press ENTER button to store. Press MENU button back to the last
menu or let the unit idle one minute to exit menu mode.
BL.O. P/T Moving—Blackout while pan/tilt moving
Select BL.O. P/T Moving, press ENTER button to confirm, present mode will
blink on the display, use UP/DOWN button to select No (normal while pan/tilt
moving) or Yes (blackout while pan/tilt moving), press ENTER button to store.
Press MENU button back to the last menu or let the unit idle one minute to
exit menu mode.
BL.O. Color Change—Blackout while change color
Select BL.O. Color Change, press ENTER button to confirm, present mode
will blink on the display, use UP/DOWN button to select No (normal while
changing color) or Yes (blackout while changing color), press ENTER button
to store. Press MENU button back to the last menu or let the unit idle one
minute to exit menu mode.
BL.O. Gobo Change—Blackout while change gobo
Select BL.O. Gobo Change, press ENTER button to confirm, present mode
will blink on the display, use UP/DOWN button to select No (normal while
changing gobo) or Yes (blackout while changing gobo), press ENTER button
to store. Press MENU button back to the last menu or let the unit idle one
minute to exit menu mode.
9-
Display Settings
Enter menu mode, select Display Settings, press ENTER button to confirm, use
UP/DOWN button to select Display Inverse, Backlight Auto Off, Backlight
Intensity or Temperature unit.
Display Inverse
Select Display Inverse, press ENTER button to confirm, present mode will
blink on the display, use UP/DOWN button to select No (normal display) or
Yes (inverse display), press ENTER button to store. Press MENU button back
to the last menu or let the unit idle one minute to exit menu mode.
Backlight Auto Off
Select Backlight Auto Off, press ENTER button to confirm, present mode
will blink on the display, use UP/DOWN button to select No (display always on)
or Yes (display goes off one minute after exiting menu mode), press ENTER
button to store. Press MENU button back to the last menu or let the unit idle
one minute to exit menu mode.
Backlight Intensity
Select Backlight Intensity, press ENTER button to confirm, present mode
will blink on the display, use UP/DOWN button to adjust backlight intensity from
1 (dark) to 10 (bright), press ENTER button to store. Press MENU button back
to the last menu or let the unit idle one minute to exit menu mode.
Temperature Unit
Select Temperature Unit, press ENTER button to confirm, present mode will
blink on the display, use UP/DOWN button to select ℃or ℉, press ENTER
button to store. Press MENU button back to the last menu or let the unit idle
one minute to exit menu mode.

10-
Fixture Test
Enter menu mode, select Fixture Test, press ENTER button to confirm, use
UP/DOWN button to selectAuto Test or Manual Test
Auto Test
Select Auto Test, press ENTER button to confirm, the unit will run built-in
programs to automatically test pan, tilt, color, gobo, gobo rotation, prism,
prism rotation, frost. Press MENU button back to the last menu or exit menu
mode after auto test.
Manual Test
Select Manual Test, press ENTER button to confirm, the present channel will
show on the display, use UP/DOWN button to select channel, press ENTER
button to confirm, then use UP/DOWN button to adjust the value, press
ENTER button to store, the fixture will run as the channel value indicates.
Press MENU button back to the last menu or exit menu mode let the unit idle
one minute.
(All channels value will become 0 after exiting Manual Test menu)
Fixture Information
Enter menu mode, select Fixture Information, press ENTER button to confirm,
use UP/DOWN button to select Fixture use time, LED use time or Firmware
Version.
Fixture use time
Select Fixture use time, press ENTER button to confirm, fixture use time will
show on the display, press MENU button to exit.
LED use time
Select LED use time, press ENTER button to confirm, lamp on time will show
on the display, press ENTER button to confirm, use UP/DOWN button to
11-
select Exit or Reset Time, press ENTER button to confirm. Press MENU
button back to the last menu or exit menu mode let the unit idle one minute.
Firmware Version
Select Firmware Version, press ENTER button to confirm, firmware version
will show on the display, press MENU button back to exit.
Reset Functions
Enter menu mode, select Reset Functions, press ENTER button to confirm, use
UP/DOWN button to select Pan/Tilt, Color, Gobo,Iris, Prism, Focus or All.
Pan/Tilt—Reset Pan/Tilt
Select Pan/Tilt, press ENTER button to confirm, use UP/DOWN button to
select Yes (the unit will run built-in program to reset pan and tilt to their home
positions) or No, press ENTER button to store. Press MENU button back to
the last menu or let the unit idle one minute to exit menu mode.
Color—Reset Color
Select Color, press ENTER button to confirm, use UP/DOWN button to select
Yes (the unit will run built-in program to reset color wheel to their home
positions) or No, press ENTER button to store. Press MENU button to exit.
Gobo—Reset Gobo
Select Gobo, press ENTER button to confirm, use UP/DOWN button to select
Yes (the unit will run built-in program to reset gobo wheel) or No, then press
ENTER button to store. Press MENU button back to the last menu or let the
unit idle one minute to exit menu mode.
Prism—Reset Prism
Select Prism, press ENTER button to confirm, use UP/DOWN button to
select Yes (the unit will run built-in program to reset prism) or No, press

12-
ENTER button to store. Press MENU button to exit.
Iris—Reset Iris
Select Iris, press ENTER button to confirm, use UP/DOWN button to select
Yes (the unit will run built-in program to reset iris to its home positions) or No,
press ENTER button to store. Press MENU button back to the last menu or let
the unit idle one minute to exit menu mode.
Focus—Reset Focus
Select Focus, press ENTER button to confirm, use UP/DOWN button to
select Yes (the unit will run built-in program to reset focus to its home
positions) or No, press ENTER button to store. Press MENU button to exit.
All—Reset All
Select All, press ENTER button to confirm, use UP/DOWN button to select
Yes (the unit will run built-in program to reset all motors to their home
positions) or No, press ENTER button to store. Press MENU button to exit.
Special Functions
Enter menu mode, select Special Functions, press ENTER button to confirm, the
Factory Setting will show on the display, press ENTER button to confirm, then use
UP/DOWN button to select Yes or No.
13-
3.4 Home Position Adjustment
Press MENU button into menu mode, then press the ENTER button for about
3 seconds into offset mode to adjust the home position. Select the function by
ENTER button. Use UP and DOWN button to choose the submenu, press the
ENTER button to store and automatically return to the last menu. Press MENU
button to exit.
Pan—pan home position adjust
Enter offset mode, Select Pan, press ENTER button to confirm, the present
position will blink on the display, use UP/DOWN button to offset the value from
-128 to 127, press ENTER button to store. Press MENU button to exit.
Tilt—Tilt home position adjust
Enter offset mode, Select Tilt, press ENTER button to confirm, the present
position will blink on the display, use UP/DOWN button to offset the value from
-128 to 127, press ENTER button to store. Press MENU button to exit.
Color1—Color home position adjust
Enter offset mode, Select Color1, press ENTER button to confirm, the present
position will blink on the display, use UP/DOWN button to offset the value from
-128~127
-128~127
Offset Menu
-128~127
-128~127
-128~127
0~255
-128~127
-128~127
0~255
-128~127
Pan
-128~127
Tilt
Color1
Gobo
Color2
R-Gobo
Gobo 2
Iris
Prism
R-Prism
Focus

14-
-128 to 127, press ENTER button to store. Press MENU button to exit.
Color2—Color home position adjust
Enter offset mode, Select Color2, press ENTER button to confirm, the present
position will blink on the display, use UP/DOWN button to offset the value from
-128 to 127, press ENTER button to store. Press MENU button to exit.
Gobo—Gobo home position adjust
Enter offset mode, Select Gobo, press ENTER button to confirm, the present
position will blink on the display, use UP/DOWN button to offset the value from
-128 to 127, press ENTER button to store. Press MENU button to exit.
R-Gobo—Gobo rotation home position adjust
Enter offset mode, Select R-Gobo, press ENTER button to confirm, the
present position will blink on the display, use UP/DOWN button to offset the value
from -128 to 127, press ENTER button to store. Press MENU button to exit.
Gobo2—Gobo home position adjust
Enter offset mode, Select Gobo 2, press ENTER button to confirm, the
present position will blink on the display, use UP/DOWN button to offset the value
from -128 to 127, press ENTER button to store. Press MENU button to exit.
Iris—Iris home position adjust
Enter offset mode, Select Iris, press ENTER button to confirm, the present
position will blink on the display, use UP/DOWN button to offset the value from 0 to
255, press ENTER button to store. Press MENU button to exit.
Prism—Prism home position adjust
Enter offset mode, Select Prism, press ENTER button to confirm, the present
position will blink on the display, use UP/DOWN button to offset the value from-128
to 127, press ENTER button to store. Press MENU button to exit.
R-Prism—Prism rotation home position adjust
Enter offset mode, Select R-Prism, press ENTER button to confirm, the
present position will blink on the display, use UP/DOWN button to offset the value
15-
from -128 to 127, press ENTER button to store. Press MENU button to exit.
Focus—Focus home position adjust
Enter offset mode, Select Focus, press ENTER button to confirm, the present
position will blink on the display, use UP/DOWN button to offset the value from 0 to
255, press ENTER button to store. Press MENU button to exit.
4. How To Control The Unit
You can operate the unit in two ways:
1. By master/slave built-in preprogram function
2. By universal DMX controller
4.1 Master/Slave Built-in Preprogram Function
By linking the units in master/slave connection, the first unit will control the
other units to give an automatic, sound activated, synchronized light show. This
function is good when you want an instant show.
4.2 DMX Controller
Use universal DMX controller to control the units, you have to set DMX
address from 1 to 512 channel so that the units can receive DMX signal.
Press the MENU button up to when the DMX Address is showing on the display.
Press ENTER button and the display will blink. Use DOWN and UP button to
change the DMX512 address. Once the address has been selected, press and
keep ENTER button to store when. To go back to the functions without any change
press the MENU button or wait for 8 seconds.
Please refer to the following diagram to address your DMX512 channel for the first
4 units:
Channel Mode Unit 1 Unit 2 Unit 3 Unit 4
17 channels 1 18 35 52

16-
5. DMX512 Configuration
17 Channels Mode:
17-
6. DMX512 Connection
1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin
adapter-cable.
2. At last unit, the DMX cable has to be terminated with a terminator. Solder a
120 ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin
XLR-plug and plug it in the DMX-output of the last unit.
3. Connect the unit together in a `daisy chain` by XLR plug from the output of the
unit to the input of the next unit. The cable can not branched or split to a `Y`
cable. DMX 512 is a very high-speed signal. Inadequate or damaged cables,
soldered joints or corroded connectors can easily distort the signal and shut
down the system.
4. The DMX output and input connectors are pass-through to maintain the DMX
circuit, when power is disconnected to the unit.
5. Each lighting unit needs to have an address set to receive the data sent by the
controller. The address number is between 0-511 (usually 0 & 1 are equal to
1).
6. The end of the DMX 512 system should be terminated to reduce signal errors.
7. 3 pin XLR connectors are more popular than 5 pin XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
Pin 4/5: Not used.

18-
7. Troubleshooting
Following are a few common problems that may occur during operation.
Here are some suggestions for easy troubleshooting:
A. The unit does not work, no light and the fan does not work
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
3. Check the power on LED.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link
properly.
2. If the DMX LED is on and no response to the channel, check the address
settings and DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or
on PCB of the unit or the previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that
may cause damage or interference to DMX interface circuit.
C. Some units don’t respond to the easy controller
1. You may have a break in the DMX cabling.
2. Check the LED for the response of the master/ slave mode signal.
D. No response to the sound
1. Make sure the unit does not receive DMX signal.
2. Check if the sound sensitively is too low.
E. One of the channels is not working well
1. The cable connected to the PCB may be broken.
8. Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried
out periodically to optimize light output. Cleaning frequency depends on the
environment in which the fixture operates: damp, smoky or particularly dirty
surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
19-
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least
every 30/60 days.
EC Declaration of Conformity
We declare that our products (lighting equipments) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN55103-1:199601-2; EN55103-2:1996;
EN61000-3-2:2000+A2:2005;
EN61000-3-3:1995+A1:2001+A2:2005.
&
Harmonized Standard
EN 60598-1: 2004
IEC 60598-1:2003+ corrigendum 2004
Part 1:General requirements and test
Following the provisions of the low voltage directive 73/23/EEC and
93/68/EEC
Innovation, Quality, Performance