ADF Web HD67605-A1 User manual

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 1 di 22
User Manual
Revision 1.000
English
PROFINET / PROFIBUS Slave -
Converter
(Order Code: HD67605-A1)
for Website information:
www.adfweb.com? roduct=HD67605
for rice information:
www.adfweb.com? rice=HD67605-A1
Benefits and Main Features:
Very easy to configure
Electrical isolation
Two ROFINET ports
Temperature range: -40°C/85°C (-40°F/185°F)
For others ROFINET products see also the following link:
Converter PROFINET to
www.adfweb.com? roduct=HD67608 (Devi eNet Master)
www.adfweb.com? roduct=HD67609 (Devi eNet Slave)
www.adfweb.com? roduct=HD67610 (J1939)
www.adfweb.com? roduct=HD67600 (NMEA2000)
www.adfweb.com? roduct=HD67601 (Serial RS232)
www.adfweb.com? roduct=HD67601 (Serial RS485)
www.adfweb.com? roduct=HD67602 (Modbus Master RS232)
www.adfweb.com? roduct=HD67602 (Modbus Master RS485)
www.adfweb.com? roduct=HD67603 (Modbus Slave RS232)
www.adfweb.com? roduct=HD67603 (Modbus Slave RS485)
www.adfweb.com? roduct=HD67604 (PROFIBUS Master)
www.adfweb.com? roduct=HD67606 (CAN)
Do you have an your customer protocol?
www.adfweb.com? roduct=HD67003
Do you need to choose a device? do you want help?
www.adfweb.com?Cmd=helpme
Other
roducts
Axis Solutions Pvt Ltd is the Authorized Distributor of $')ZHE in India
www.axisindia.in | [email protected]
Axis Solutions Pvt Ltd is the Authorized Distributor of $')ZHE in India
www.axisindia.in | [email protected]
Axis Solutions Pvt Ltd is the Authorized Distributor of $')ZHE in India
www.axisindia.in | [email protected]
Axis Solutions Pvt Ltd is the Authorized Distributor of $')ZHE in India
www.axisindia.in | [email protected]

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 2 di 22
INDEX:
age
INDEX 2
U DATED DOCUMENTATION 2
REVISION LIST 2
WARNING 2
TRADEMARKS 2
SECURITY ALERT 3
EXAM LE OF CONNECTION 4
CONNECTION SCHEME 5
CHARACTERISTICS 6
CONFIGURATION 6
OWER SU LY 7
FUNCTION MODES 8
LEDS 9
ROFIBUS 10
ROFINET 10
USE OF COM OSITOR SW67605 11
NEW ROJECT / O EN ROJECT 11
SET COMMUNICATION 12
ROFINET XML 13
ROFIBUS GSD 13
U DATE DEVICE 14
MECHANICAL DIMENSIONS 16
ORDERING INFORMATIONS 17
ACCESSORIES 17
LC CONFIGURATION 18
DISCLAIMER 21
OTHER REGULATIONS AND STANDARDS 21
WARRANTIES AND TECHNICAL SU ORT 22
RETURN OLICY 22
RODUCTS AND RELATED DOCUMENTS 22
UPDATED DOCUMENTATION:
Dear customer, we thank you for your attention and we remind you that
you need to check that the following document is:
Updated
Related to the product you own
To obtain the most recently updated document, note the “document code”
that appears at the top right-hand corner of each page of this document.
With this “Document Code” go to web page www.adfweb.com/download/
and search for the corresponding code on the page. Click on the proper
“Document Code” and download the updates.
To obtain the updated documentation for the product that you own, note
the “Document Code” (Abbreviated written "Doc. Code" on the label on the
product) and download the updated from our web site
www.adfweb.com/download/
REVISION LIST:
WARNING:
ADFweb.com reserves the right to change information in this manual about
our product without warning.
ADFweb.com is not responsible for any error this manual may contain.
TRADEMARKS:
All trademarks mentioned in this document belong to their respective
owners.
Revision Date Author Chapter Des ription
1.000 07/09/2012 Dp All First Release

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 3 di 22
SECURITY ALERT:
G ENERAL I NFORMATION
To ensure safe operation, the device must be operated according to the instructions in the manual. When using the device are required for
each individual application, legal and safety regulation. The same applies also when using accessories.
I NTENDED U SE
Machines and systems must be designed so the faulty conditions do not lead to a dangerous situation for the operator (i.e. independent limit
switches, mechanical interlocks, etc.).
Q UALIFIED P ERSONNEL
The device can be used only by qualified personnel, strictly in accordance with the specifications.
Qualified personnel are persons who are familiar with the installation, assembly, commissioning and operation of this equipment and who
have appropriate qualifications for their job.
R ESIDUAL R ISKS
The device is state of the art and is safe. The instrument can represent a potential hazard if they are inappropriately installed and operated
by personnel untrained. These instructions refer to residual risks with the following symbol:
This symbol indicates that non-observance of the safety instructions is danger for people to serious injury or death and / or the
possibility of damage.
CE CONFORMITY
The declaration is made by us. You can send an email to [e-mail] or give us a call if you need it.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 4 di 22
EXAMPLE OF CONNECTION:

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 5 di 22
CONNECTION SCHEME:
Figure 1: Connection scheme for HD67605-A1

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 6 di 22
CHARACTERISTICS:
The HD67605-A1 is a ROFINET / ROFIBUS Slave Converter.
It allows the following characteristics:
Up to 244 bytes in reading and 244 bytes in writing;
Triple isolation between ROFIBUS - ower Supply, ROFIBUS - Ethernet, ower Supply - Ethernet.
Two-directional information between ROFIBUS bus and ROFINET bus;
Mountable on 35mm Rail DIN;
Wide power supply input range: 8…24V AC or 12…35V DC;
Wide temperature range: -40°C / 85°C [-40°F / +185°F].
CONFIGURATION:
You need Compositor SW67605 software on your C in order to perform the following:
Define the parameter of ROFINET line;
Define the parameter of ROFIBUS line;
Update the device.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 7 di 22
POWER SUPPLY:
The devices can be powered at 8…24V AC and 12…35V DC. For more details see the two tables below.
VAC
VDC
Vmin Vmax Vmin Vmax
8V 24V 12V 35V
Consumption at 24V DC:
Devi e Consumption [W/VA]
HD67605-A1 3.5
HD67
605
-
A1
Caution: Not reverse the polarity power

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 8 di 22
FUNCTION MODES:
The device has got two functions mode depending of the position of the ‘Dip2 of Dip-Switch B’:
The first, with ‘Dip2 of Dip-Switch B’ at “OFF” position, is used for the normal working of the device.
The second, with ‘Dip2 of Dip-Switch B’ at “ON” position, is used for upload the roject and/or Firmware.
For the operations to follow for the updating, see ‘U DATE DEVICE’ section.
According to the functioning mode, the LEDs will have specifics functions, see ‘LEDS’ section.
Warning:
Dip1 of ‘Dip-Switch B’ must be at ON position for working even if the Ethernet cable isn’t inserted.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 9 di 22
LEDS:
The device has got six LEDs that are used to give information of the functioning status.
The various meanings of the LEDs are described in the table below.
LED Normal Mode Boot Mode
1: ON [supply voltage ]
(green)
ON: Device powered
OFF: Device not powered
ON: Device powered
OFF: Device not powered
2: MT [maintenance display]
(yellow)
ON: Maintenance roblem is present
OFF: No maintenance are present
Blinks qui kly: Boot state
Blinks very slowly (~0.5Hz): update in progress
3: BF [bus fault] (red)
ON: The Ethernet connection is defective; the I
address exists several times in the network; the own
NameOfStation exists several times in the network; no
I address has been set
Flashing: At least one configured AR is no longer in
the data exchange
OFF: No errors are present
Blinks qui kly: Boot state
Blinks very slowly (~0.5Hz): update in progress
4: SF [group error] (red) ON: At least one AR is not in the data exchange
OFF: No errors are present
Blinks qui kly: Boot state
Blinks very slowly (~0.5Hz): update in progress
5: Ethernet1 Tx (green) Blinks when is transmitting Ethernet frames Blinks qui kly: Boot state
Blinks very slowly (~0.5Hz): update in progress
6: Ethernet2 Tx (green) Blinks when is transmitting Ethernet frames Blinks qui kly: Boot state
Blinks very slowly (~0.5Hz): update in progress

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 10 di 22
PROFIBUS:
The ROFIBUS uses a 9-pin D-SUB connector. The pin assignment is defined
like in the right figure.
Here some codes of cables:
Belden: p/n 183079A - Continuous Armor DataBus® ISA/S -50
ROFIBUS Cable.
PROFINET:
The ROFINET connection must be made using Connector3 and/or Connector4 of HD67605-A1 with at least a Category 5E cable. The
maximum length of the cable should not exceed 100m. The cable has to conform to the T568 norms relative to connections in cat.5 up to
100 Mbps. To connect the device to an Hub/Switch is recommended the use of a straight cable, to connect the device to a C/ LC/other is
recommended the use of a cross cable.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 11 di 22
USE OF COMPOSITOR SW67605:
To configure the Converter, use the available software that runs with
Windows, called SW67605. It is downloadable on the site www.adfweb.com
and its operation is described in this document. (This manual is referenced to
the last version of the software present on our web site). The software works
with MSWindows (MS 2000, X , Vista, Seven, 8; 32/64bit).
When launching the SW67605 the right window appears (Fig. 2).
NEW PROJECT / OPEN PROJECT:
The “New Proje t” button creates the folder which contains the entire device configuration.
A device configuration can also be imported or exported:
To clone the configurations of a programmable “ ROFINET / ROFIBUS Slave – Converter”
in order to configure another device in the same manner, it is necessary to maintain the
folder and all its contents;
To clone a project in order to obtain a different version of the project, it is sufficient to
duplicate the project folder with another name and open the new folder with the button
“Open Proje t”.
Figure
2
:
Main window
for
SW
67
60
5

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 12 di 22
SET COMMUNICATION:
This section define the fundamental communication parameters of two buses, ROFINET and
ROFIBUS Slave.
By ressing the “Set Communi ation” button from the main window for SW67605 (Fig. 2) the
window “Set Communication” appears (Fig. 3).
The window is divided in two sections, one for the ROFINET and the other for the ROFIBUS
Slave.
The means of the fields for “ ROFINET” are:
In the fields “IP ADDRESS” insert the I address that you want to give to the Converter;
In the fields “SUBNET Mask” insert the SubNet Mask;
In the fields “GATEWAY” insert the default gateway that you want to use. This feature can
be enabled or disabled pressing the Check Box field. This feature is used for going out of
the net;
In the field “Port” the port used for ROFINET communication is defined. The port has a
fixed value of 34964;
In the field "PROFINET Name of Station" is possible to assign a name to the ROFINET
node.
The means of the fields for the “ ROFIBUS Slave” section are:
In the “ID Devi e” field the ROFIBUS Slave ID is defined.
In the “Baudrate” field the ROFIBUS Slave baudrate is defined (fixed to Auto Baudrate).
In the field “Number Byte IN” the number input bytes of ROFIBUS Slave is defined (at
max 244 bytes);
In the field “Number Byte OUT” the number output bytes of ROFIBUS Slave is defined
(at max 244 bytes).
Figure
3
:
“Set Communication” window

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 13 di 22
PROFINET XML:
By pressing the “PROFINET XML” button it is possible to save the GSDML file for the ROFINET side.
With this feature you can save the configuration of the converter of the ROFINET side.
PROFIBUS GSD:
By pressing the “PROFIBUS GSD” button it is possible to save the GSD file for the ROFIBUS side.
With this feature you can save the configuration of the converter of the ROFIBUS side.
Note:
When you import the .gsd file on your Master ROFIBUS you have to add all the modules that are present inside it.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 14 di 22
UPDATE DEVICE:
By pressing the “Update Devi e” button it is possible to load the created Configuration into the
device; and also the Firmware, if is necessary.
If you don’t know the actual I address of the device you have to use this procedure:
Turn off the Device;
ut Dip2 of ‘Dip-Switch B’ at ON position;
Turn on the device
Connect the Ethernet cable;
Insert the I “192.168.2.205”;
ress the “Ping” button, must appear “Device Found!”;
ress the “Next” button;
Select which operations you want to do;
ress the “Exe ute update firmware” button to start the upload;
When all the operations are “OK” turn off the Device;
ut Dip2 of ‘Dip-Switch B’ at OFF position;
Turn on the device.
At this point the configuration/firmware on the device is correctly updated.
Figure 8: “Update device” windows

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 15 di 22
If you know the actual I address of the device you have to use this procedure:
Turn on the Device with the Ethernet cable inserted;
Insert the actual I of the Converter;
ress the “Ping” button, must appear “Device Found!”;
ress the “Next” button;
Select which operations you want to do;
ress the “Exe ute update firmware” button to start the upload;
When all the operations are “OK” the device automatically goes at
Normal Mode.
At this point the configuration/firmware on the device is correctly update.
Note:
When you install a new version of the software it is better if the first time you do the update of the Firmware in the HD67605-A1
device.
Note:
When you receive the device, for the first time, you have to update also the Firmware in the HD67605-A1 device.
Warning:
If the Fig. 9 appears when you try to do the Update before require assistance try
these points:
Try to repeat the operations for the updating;
Try with another C;
Try to restart the C;
If you are using the program inside a Virtual Machine, try to use in the main
Operating System;
If you are using Windows Seven or Vista or 8, make sure that you have the
administrator privileges;
Take attention at Firewall lock;
Check the LAN settings.
In the case of HD67605-A1 you have to use the software “SW67605”: www.adfweb.com\download\filefold\SW67605.zip.
Figure 9: “ rotection” window

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 16 di 22
MECHANICAL DIMENSIONS:
Figure
1
0
: Mechanical dimensions scheme
for HD67
60
5
-
A1

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 17 di 22
ORDERING INFORMATIONS:
The ordering part number is formed by a valid combination of the following:
HD67605 – A 1
Conne tors Type
1: Removable 5mm Screw Terminal
En losure Type
A: 1M, 35mm DIN Rail mounting
Devi e Family
HD67605: ROFINET / CAN - Converter
Order Code: HD67605-A1 - ROFINET / CAN - Converter
ACCESSORIES:
Order Code: AC34001 - 35mm Rail DIN - ower Supply 220/240V AC 50/60Hz – 12 V AC
Order Code: AC34002 - 35mm Rail DIN - ower Supply 110V AC 50/60Hz – 12 V AC

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 18 di 22
PLC CONFIGURATION:
The configuration and commissioning of the ROFINET Converter as described on the following pages was accomplished with the help of the
TIA ortal V11-software of Siemens. In case of using a control system from another supplier please attend to the associated documentation.
These are the steps to follow:
1) Install the description file of the module.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 19 di 22
2) Import the module in the network; connect the device to the LC network and edit the parameters of I , station name etc.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
PROFINET
/
PROFIBUS Slave
Document code: MN67605_ENG Revision 1.000 agina 20 di 22
3) Load the configuration into the LC.