ADTRAN 1442200G1 User manual

jobAid
1
DESCRIPTION
The ADTRAN 100Base-TX, RJ-45 Copper Small Form-Factor
Pluggable (SFP) plugs into appropriate ADTRAN Ethernet
modules to provide a 100Base-TX interface over an RJ-45 type
copper connector.
The SFP supports the following features:
■100Base-TX compliant
■Auto-Negotiation: full-duplex or half-duplex
■Uses Category 5 or 5e shielded twisted-pair cable (or better)
NOTICE
The SFP may not operate in all SFP-based Ethernet modules. To
determine if the SFP is appropriate for use in a particular module,
refer to the documentation for that module, or contact ADTRAN
Customer Support.
NOTE
The SFP does not support Auto-MDIX.
INSTALLATION
Prior to installation, inspect the SFP. If damage has occurred
during shipping, file a claim with the carrier, and then contact
ADTRAN Customer Support. Refer to “Warranty” on page 2.
To install the SFP into an appropriate module, complete the
following steps:
1. If present, remove the safety cap from the connector of the SFP.
2. Insert the SFP into the SFP cage of the host module, with the
removal latch facing outward. Slide the SFP all the way into the
cage.
3. Firmly squeeze the receptacle and SFP together, to ensure a
proper connection.
NOTE
The latch on the SFP is for removal only.
4. Continue the installation and turn-up of the host
module using the instructions in the documentation
provided with the module or other system-level
documentation available online at www.adtran.com.
Small Form-Factor Pluggable,
100Base-TX, RJ-45 Copper
SPECIFICATIONS
■General
♦Module type: SFP
♦Media Type: Copper
♦Signal data rate: 1.25 Gbps
♦Applications: Migration and integration of transport in
packet switching networks
♦Diagnostic Monitoring: No
♦Distance: Maximum (over Cat 5 cable): 100 meters
■Operates in modules supporting the following voltage inputs
♦±24 VDC Nominal (±20.0 VDC to ±28.3 VDC)
♦–48 VDC Nominal (–40.0 VDC to –56.7 VDC)
■Environmental
♦Protected Equipment Environment (Outside)
●Operational temperature range: –40°C to +65°C
●Storage temperature range: –40°C to +85°C
●Relative humidity: 5 to 85%
■Extended environmental support
♦Controlled Protected Environment (Inside)
●Operational temperature range: –5°C to + 55°C
●Storage temperature range: –40°C to +85°C
●Relative humidity 5 to 85%
MAINTENANCE
The SFP does not require routine hardware maintenance for
normal operation. ADTRAN does not recommend that repairs be
attempted in the field. Repair services may be obtained by
returning the defective unit to ADTRAN. Field support for
software is provided through upgrade facilities. Refer to
“Warranty” for further information.
CLEI: SOUIBVOL_ _
Product P/N: 1442200G1
Issue Date: November 2018
Document P/N: 61442200G1-22B

Warranty: ADTRAN will replace or repair this product within the warranty period if it does not meet
its published specifications or fails while in service. Warranty information can be found
online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
©2018 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.800.726.8663
From outside the U.S. 1.256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61442200G1-22B*
SAFETY AND REGULATORY
WARNING
!
■The Ethernet port is classified as Type 2 or Type 4, as defined in
GR-1089-CORE, Issue 5, Appendix B, and is suitable for
connection to intrabuilding or unexposed wiring or cabling
only. Do not metallically connect this port to any interface
which connects to the Outside Plant (OSP) or to the OSP wiring.
The addition of Primary Protectors is not sufficient protection
in order to connect this interface metallically to OSP wiring.
■The Ethernet port is suitable for connection only to shielded
intra-building cabling, grounded at both ends.
!CAUTION
■Electrostatic Discharge (ESD) can damage electronic modules.
When handling electronic components, wear an antistatic
discharge wrist strap to prevent damage. Place modules in
antistatic packing material when transporting or storing. When
working on modules, always place them on an approved
antistatic mat that is electrically grounded.
■This product is NRTL listed to all applicable UL standards. This
product meets or exceeds all applicable requirements of NEBS,
Telcordia GR-63-CORE, GR-78-CORE, and GR-1089-CORE.
This product is intended for deployment in Central Office type
facilities, EEEs, EECs, and locations where the NEC applies
(e.g., Customer Premises).
■This product should be installed by qualified Service Personnel
only, in an ADTRAN module intended for installation in an
ADTRAN host system located in a restricted access location.
■Per GR-1089-CORE this product is designed and intended for
installation as part of a Common Bonding Network (CBN). This
product is not designed nor intended for installation as part of
an Isolated Bonding Network (IBN).
■Per GR-1089-CORE, Section 9, this product does not have an
internal DC connection between –48 VR and frame ground.
This product can be deployed in an Isolated (DC-I) or Common
(DC-C) configuration. For installations where other modules or
the host system have internal connections between –48 VR and
frame ground, the system would be intended for deployment
only in a DC-C configuration.
■The host chassis frame ground terminal must be connected to
an earth ground to ensure that the metal enclosure of this
product is properly grounded via the backplane connector.
NOTE
■This product is designed for deployment in GR-3108-CORE
environmental class 1 and 2, as defined in GR-3108-CORE,
Issue 2.
■This product is designed to meet the following environmental
classes:
♦ETSI EN 300 019-1-1 “Classification of environmental condi-
tions; Storage,” Class 1.2
♦ETSI EN 300 019-1-2 “Classification of environmental condi-
tions; Transportation,” Class 2.3
♦ETSI EN 300 019-1-3 “Classification of environmental condi-
tions; Stationary use at weather-protected locations,” Class
3.3
■The equipment is designed to function without degradation
during exposure to all test severities per Class 019-1-3 3.3.
■This product complies with ETSI EN 300 386 “Electromagnetic
compatibility and Radio spectrum Matters (ERM);
Telecommunication network equipment;
Electromagnetic Compatibility (EMC) requirements.”
■This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
■Changes or modifications not expressly approved by ADTRAN
could void the user’s authority to operate this equipment.
■This product meets the EU RoHS Directive 2002/95/EC and/or
applicable exemptions. For more information on RoHS/WEEE,
refer to www.adtran.com.
C A U T I O NC A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.