ADTRAN BVL3AH1D Series User manual

jobAid
1
DESCRIPTION
The Small Form-Factor Pluggable
9.95 - 11.3G, Single-Mode 20 km
(SFP+) optical transceiver is a fully
duplex serial electric, serial optical
device with both transmit and
receive functions contained in a
single module that provides a high
speed serial link of up to 11.3 Gbs.
Installed into an appropriate host module, the SFP+ provides an
11.3 Gigabit interface to the supporting system.
The transmit side of the SFP+ converts serial NRZ electrical data
at the 11.3 Gbs line rate to a standard compliant optical signal.
The receive side of the SFP+ converts the incoming DC balanced
serial NRZ optical data at the 11.3 Gbs line rate into serial
electrical data.
The following features are supported on the SFP+:
■1310 nm optical signals for up to 20 km reach
■Case temperature hardened range from –40°C to 85°C
■Low power consumption (<1.5 W max)
■Bit error rate (<1x10-12)
■Excellent EMI performance
CAUTION
!
Due to compliance certification requirements, use only SFP+s
supplied by ADTRAN with the host module. ADTRAN cannot
certify system integrity with other SFP+s.
Operational Specifications
■Optical Specifications:
♦1310 nm optical signals for up to 20 km reach
♦Data rate: 9.953 to 11.3 Gbs
♦Optical transmit level: –5.0 to +1.5 dBm
♦Optical receive level sensitivity: –12.6 dBm (+0.5)
♦Optical distance: 20 km maximum
♦Optical connectors: LC
■Extended Environmental Support:
♦Operational temperature range: –40°C to +85°C
♦Storage temperature range: –40°C to +85°C
♦Relative humidity to 85%, noncondensing
Small Form-Factor Pluggable
9.95 - 11.3G, Single-Mode, 20 km, SFP+
INSTALLATION
Before installing the equipment, inspect the SFP+. If damage has
occurred during shipping, file a claim with the carrier, and then
contact ADTRAN Customer Support. For more information, refer
to the warranty.
Installation Guidelines
The following are guidelines for this installation:
■Do not remove the protective end cap from the SFP+ until the
fiber optic cable is ready to be connected.
■The latch on the SFP+ is for removal only. When removing the
SFP+, rotate the latch away from the SFP+, the SFP+ should
easily slide out of the cage.
■Ensure that the protective end cap remains on whenever the
transceiver optical fiber connector is not inserted.
Installation Steps
ToinstalltheSFP+intoanappropriatemodule,completethe
followingsteps:
1. Insert the SFP+ into the cage on the module. Ensuring that
the latch handle on the SFP+ is facing upward, slide the
SFP+ all the way into the SFP+ cage until there is an audible
“click”.
2. Do not remove the protective end cap until the optical fiber
connection is made.
3. Continue the installation and turn-up of the host module
using the instructions in the Job Aid provided with the
module or other system-level documentation available
online at www.adtran.com.
PROVISIONING
The SFP+ is not provisionable. For configuration or status infor-
mation, access the menu system of the host module. Refer to the
“Provisioning” section of the host module documentation for
provisioning details.
MAINTENANCE
The SFP+ does not require routine hardware maintenance for
normal operation. Repair services may be obtained by returning
the defective unit to ADTRAN. Refer to the warranty for further
information.
CLEI: BVL3AH1D_ _
Product P/N: 1442420G1
Issue Date: February 2015
Document P/N: 61442420G1-22C
Documentation for ADTRAN Carrier Networks products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following related online documents and resources provide additional information for this
product:
SFP/XFP/SFP+ Compatibility Matrix (Online Tool: www.adtran.com/SFP)

261442420G1-22C
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.
This product is designed to meet the following environmental
classes:
■ETSI EN 300 019-1-1: “Classification of environmental
conditions; Storage,” Class 1.2
■ETSI EN 300 019-1-2: “Classification of environmental
conditions; Transportation,” Class 2.3
■ETSI EN 300 019-1-3: “Classification of environmental
conditions; Stationary use at weather-protected locations,”
Class 3.2
The equipment is designed to function without degradation
during exposure to all test severities per Class 3.2 of ETSI EN 300
019-1-3.
This product meets EU RoHS Directive 2002/95/EC and/or
applicable exemptions. Refer to www.adtran.com for further
information on RoHS/WEEE.
SAFETY AND REGULATORY COMPLIANCE
WARNING
!
Read all warnings and cautions before installing or servicing this
equipment.
CAUTION
C
This product uses a Class 1 Laser module that complies with 21
CFR 1040.10 and 1040.11 and IEC 60825-1, IEC 60825-2, EN 60825-
1 and EN 60825-2. For continued compliance with the above
standards, only approved Class 1 laser modules from an
ADTRAN approved vendor list (located on the ADTRAN
website) should be installed in this product. ADTRAN cannot
certify system integrity with other laser modules.
CAUTION
!
■Electrostatic Discharge (ESD) can damage electronic modules.
When handling modules, wear an antistatic discharge wrist
strap to prevent damage to electronic components. Place
modules in antistatic packing material when transporting or
storing. When working on modules, always place them on an
approved antistatic mat that is electrically grounded.
■Per GR-1089-CORE the system is designed and intended for
installation as part of a Common Bonding Network (CBN). The
system is not designed nor intended for installation as part of
an Isolated Bonding Network (IBN).
■Per GR-1089-CORE Section 9, this product does not have an
internal DC connection between battery return and frame
ground. This product can be installed in a DC-I (isolated) or
DC-C (common) installation. For installations where other
cards or the host system have internal connections between
battery return and frame ground, the system would be
intended for deployment only in a DC-C installation.
■The chassis frame ground terminal must be connected to an
earth ground to ensure that the metal enclosure of the SFP is
properly grounded via the backplane connector.
NOTE
■The Gigabit Ethernet port(s) are optical and therefore are not
classified as any type of port as defined in Appendix B of GR-
1089-CORE.
■This product is compliant with SFF-8472 “Digital Diagnostics
Monitoring Interface for Optical Transceivers,” Revision 9.3.
■This product is compliant with the SFP Multi-Source
Agreement (MSA).
■This product is designed to be deployed in GR-3108-CORE
environmental class 1, 2 or 3 as defined in GR-3108-CORE.
This product meets or exceeds all the applicable requirements of
NEBS, Telcordia GR-63-CORE, GR-1089-CORE, and ETSI EN
300368. This product is intended for deployment in Central Office
type facilities, EEEs, EECs, and locations where the NEC applies
(for example, Customer Premises).
This product is to be installed in ADTRAN products in Restricted
Access Locations only, and installed by trained service personnel.

61442420G1-22C 3
FRANÇAIS
AVERTISSEMENT
!
Lisez tous les avertissements et mises en garde avant l’installation
de cet équipement ou la réalisation de toute opération de mainte-
nance.
ATTENTION
C
Ce produit utilise un module laser de classe 1 qui conforme aux
normes 21 CFR 1040.10, 1040.11 et IEC 60825-1 et -2. Pour assurer
la conformité aux normes mentionnées plus haut, seuls des
modules laser de classe 1 approuvés provenant d’une liste de
fournisseurs certifiés par ADTRAN (disponible sur le site
d’ADTRAN) doivent être installés sur ce produit. ADTRAN ne
peut certifier l’intégrité d’un système doté d’autres modules laser.
ATTENTION
!
■L'ESD (décharge électrostatique) peut endommager les
modules électroniques. Lors de la manipulation des modules,
portez un bracelet de décharge antistatique pour éviter
d’endommager les composants électroniques. Placez les
modules dans un emballage antistatique lors du transport ou
du stockage. Lorsque vous travaillez sur les modules, placez-les
toujours sur un tapis antistatique certifié muni d’un
branchement de mise à la terre.
■La borne de mise à la terre du châssis doit être branchée à une
prise de terre afin d’assurer que le boîtier métallique de la SFP
est correctement mis à la terre grâce au connecteur de face
arrière.
Les changements ou modifications non expressément approuvés
par ADTRAN pourraient annuler l'autorisation de l'utilisateur
d’utiliser cet équipement.
Ce produit est conçu pour répondre aux classes environnemen-
tales suivantes :
■ETSI EN 300 019-1-1: “Classification des conditions
d'environnement; Entreposage,” Classe 1.2
■ETSI EN 300 019-1-2: “Classification des conditions
d'environnements; Transport,” Classe 2.3
■ETSI EN 300 019-1-3: “Classification des conditions
d'environnements; l'utilisation à poste fixe dans des endroits
protégés contre les intempéries,” Classe 3.3
L'équipement est conçu pour fonctionner sans dégradation lors
des tests à tous les niveaux de sévérité, suivant les spécifications
de la classe 3.3 de l'ETSI EN 300 019-1-3.
Ce produit est conforme à la directive européenne RoHS 2002/
95/CE et/ou aux exonérations applicables. Reportez-vous à
www.adtran.com pour de plus amples renseignements sur
RoHS/WEEE.
DEUTSCH
WARNUNG
!
Lesen Sie sich alle Warn- und Sicherheitshinweise durch, bevor
Sie dieses Gerät installieren oder warten.
VORSICHT
C
Dieses Produkt nutzt ein mit den Richtlinien 21 CFR 1040.10 und
1040.11 und IEC 60825-1 und -2 konformes Class 1 Lasermodul.
Damit die obigen Richtlinien auch in Zukunft eingehalten werden
können, dürfen ausschließlich Class 1 Lasermodule von einem
von ADTRAN zugelassenen Anbieter in dem Produkt installiert
werden (erhältlich auf der Website von ADTRAN). ADTRAN
garantiert nicht für die Systemintegrität bei anderen
Lasermodulen.
VORSICHT
!
■Elektrostatische Entladungen können elektronische Module
beschädigen. Tragen Sie beim Umgang mit Modulen ein
Erdungsarmband, um Schäden an den elektronischen
Komponenten zu vermeiden. Transportieren oder lagern Sie
Module in antistatischem Verpackungsmaterial. Bei der Arbeit
an den Modulen, achten Sie darauf, diese stets auf antistatische,
elektrisch geerdete Matten zu legen.
■Die Erdungsschiene des Rahmens muss an eine Bodenstation
angeschlossen werden, um sicherzustellen, dass das
Metallgehäuse des SFP vorschriftsmäßig über den
Rückwandanschluss geerdet ist.
Durch Änderungen oder Umbauten, die von ADTRAN nicht
ausdrücklich genehmigt wurden, kann der Nutzer die
Berechtigung zur Bedienung dieses Geräts verlieren.
Dieses Produkt wurde entsprechend der folgenden Umweltk-
lassen entwickelt:
■ETSI EN 300 019-1-1: “Klassifikation von
Umweltbedingungen, Lagerung,” Klasse 1.2
■ETSI EN 300 019-1-2: “Klassifikation von
Umweltbedingungen, Transport,” Klasse 2.3
■ETSI EN 300 019-1-3: “Klassifikation von
Umweltbedingungen, Stationärer Einsatz ohne
Witterungseinflüsse,” Klasse 3.3
Dieses Gerät funktioniert ohne Leistungsabfall während aller für
Klasse 3.3 von ETSI EN 300 019-1-3 vorgeschriebenen Belastung-
stests.
Dieses Produkt erfüllt die EU RoHS Richtlinie 2002/95/EC und/
oder gültige Ausnahmen. Bitte besuchen Sie www.adtran.com für
ausführlichere Informationen zu RoHS/WEEE.

Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service.
Warranty information can be found online at
www.adtran.com/warranty.
©2015 ADTRAN, Inc. All Rights Reserved.
CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
ADTRAN CUSTOMER CARE:
From within the U.S. 1.800.726.8663
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61442420G1-22C*