ADTRAN BVL3ARLD Series User manual

jobAid
1
DESCRIPTION
The SFP+, 11.3 Gbps, 1550 nm, SMF, 80 km optical transceiver is a
fully duplex serial electric, serial optical device with both transmit
and receive functions contained in a single module. It provides a
high speed serial link at a rate of 11.3 Gbps. When installed into
an appropriate host module, the SFP+ provides an 11.3 Gbps
interface to the supporting system.
The transmit side of the SFP+ converts serial NRZ electrical data
at 11.3 Gbps line rate to a standard compliant optical signal. The
receive side of the SFP+ converts the incoming DC balanced serial
NRZ optical data at 11.3 Gbps line rate into serial electrical data.
NOTE
To ensure compatibility, refer to the documentation provided
with the host module.
The following features are supported on the SFP+:
■1550 nm optical signals for up to 80 km reach
■Low power consumption (<1.5 W max)
■Bit error rate (<1x10-12)
■Excellent EMI performance
CAUTION
!
Due to compliance certification requirements, only SFP+s
supplied by ADTRAN are to be used with the host module.
ADTRAN cannot certify system integrity with other SFP+
modules.
Small Form-factor Pluggable
SFP+, 11.3 Gbps, 1550 nm, SMF, 80 km
Specifications
Optical
■1550 nm optical signals for up to 80 km reach
■Data rate: 9.95 to 11.3 Gbps
■Optical transmit level: 0 to +4.0 dBm
■Optical receive level sensitivity: –24 dBm
■Optical Receiver Overload: –7 dBm
■Path-penalty: 3 dB
■Optical Budget: 21 dB
■Max Span attenuation: 20 dB
■Optical distance: 80 km maximum
■Optical connectors: LC
Environmental
■Protected Equipment Severe Environment (Outside):
♦Operational temperature range: –40°C to +70°C
●Case temperature hardened range: –40°C to +85°C
♦Storage temperature range: –40°C to +85°C
♦Relative humidity 5 to 90%
INSTALLATION
Before installing the equipment, inspect the SFP+. If damage has
occurred during shipping, file a claim with the carrier, and then
contact ADTRAN Customer Support. For more information, refer
to the warranty.
To install the SFP+ into an appropriate module, complete the
following steps:
NOTE
Do not remove the protective end cap from the SFP+ until the
fiber optic cable is ready to be connected.
1. Insert the SFP+ into the SFP+ cage on the module. Ensuring
that the latch handle on the SFP+ is facing upward, slide the
SFP+ all the way into the SFP+ cage until there is an audible
“click”.
NOTE
The latch on the SFP+ is for removal only. When removing the
SFP+, rotate the latch away from the SFP+, the SFP+ should easily
slide out of the cage.
CLEI: BVL3ARLD_ _
Product P/N: 1442480F1
Issue Date: February 2016
Document P/N: 61442480F1-22A
Documentation for ADTRAN Access & Aggregation products
is available for viewing and download directly from the
ADTRAN Support Community website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including
customized training and courses taught at our facilities or at
customer sites.
For inquiries, go to: http://adtran.com/training
The following related online documents and resources provide additional information for this product:
SFP/XFP/SFP+ Compatibility Matrix (online tool: http://www.adtran.com/sfp)

261442480F1-22A
NOTE
■The Gigabit Ethernet port(s) are optical and therefore are not
classified as any type of port as defined in Appendix B of GR-
1089-CORE.
■This product is compliant with SFF-8472 “Digital Diagnostics
Monitoring Interface for Optical Transceivers,” Revision 9.3.
■This product is compliant with the SFP Multi-Source
Agreement (MSA).
■This product is designed to be deployed in GR-3108-CORE
environmental class 1, class 2 and class 3 as defined in GR-
3108-CORE.
This product meets or exceeds all the applicable requirements of
NEBS, Telcordia GR-63-CORE, GR-1089-CORE, and ETSI EN
300368. This product is intended for deployment in Central Office
type facilities, EEEs, EECs, and locations where the NEC applies
(for example, Customer Premises).
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.
This product is designed to meet the following environmental
classes:
■ETSI EN 300 019-2-1: “Classification of environmental conditions;
Storage,” Class 1.2
■ETSI EN 300 019-2-2: “Classification of environmental conditions;
Transportation,” Class 2.3
■ETSI EN 300 019-2-3: “Classification of environmental conditions;
Stationary use at weather-protected locations,” Class 3.2
The equipment is designed to function without degradation
during exposure to all test severities per Class 3.2 of ETSI EN 300
019-1-3.
This product meets EU RoHS Directive 2011/65/EU and/or
applicable exemptions. Refer to www.adtran.com for further
information on RoHS/WEEE.
2. Remove the end cap and connect the fiber to the SFP+.
NOTICE
It is recommended that the protective end cap remain on
whenever the transceiver optical fiber connector is not in use.
3. Continue the installation and turn-up of the host module
using the instructions in the Job Aid provided with the
module or other system-level documentation available
online at www.adtran.com.
MAINTENANCE
The SFP+ does not require routine hardware maintenance for
normal operation. ADTRAN does not recommend that repairs be
attempted in the field. Repair services may be obtained by
returning the defective unit to ADTRAN. Refer to the warranty
for further information.
SAFETY AND REGULATORY COMPLIANCE
WARNING
!
Read all warnings and cautions before installing or servicing this
equipment.
CAUTION
C
This product uses a Class 1 Laser module that complies with 21
CFR 1040.10 and 1040.11 and IEC 60825-1, IEC 60825-2, EN 60825-
1 and EN 60825-2. For continued compliance with the above
standards, only approved Class 1 laser modules from an
ADTRAN approved vendor list (located on the ADTRAN
website) should be installed in this product. ADTRAN cannot
certify system integrity with other laser modules.
CAUTION
!
■Electrostatic Discharge (ESD) can damage electronic modules.
When handling modules, wear an antistatic discharge wrist
strap to prevent damage to electronic components. Place
modules in antistatic packing material when transporting or
storing. When working on modules, always place them on an
approved antistatic mat that is electrically grounded.
■This product is designed and intended only for deployment in
a DC-C (common) bonding and grounding configuration. This
product is not intended or designed for deployment in a DC-I
(isolated) bonding and grounding system.
■Per GR-1089-CORE the system is designed and intended for
installation as part of a Common Bonding Network (CBN).
The system is not designed nor intended for installation as
part of an Isolated Bonding Network (IBN).
■The chassis frame ground terminal must be connected to an
earth ground to ensure that the metal enclosure of the SFP is
properly grounded via the backplane connector.

61442480F1-22A 3
FRANÇAIS
AVERTISSEMENT
!
Lisez tous les avertissements et mises en garde avant l’installation
de cet équipement ou la réalisation de toute opération de
maintenance.
ATTENTION
C
Ce produit utilise un module laser de classe 1 qui conforme aux
normes 21 CFR 1040.10, 1040.11 et IEC 60825-1 et -2. Pour assurer
la conformité aux normes mentionnées plus haut, seuls des
modules laser de classe 1 approuvés provenant d’une liste de
fournisseurs certifiés par ADTRAN (disponible sur le site
d’ADTRAN) doivent être installés sur ce produit. ADTRAN ne
peut certifier l’intégrité d’un système doté d’autres modules laser.
ATTENTION
!
■L'ESD (décharge électrostatique) peut endommager les
modules électroniques. Lors de la manipulation des modules,
portez un bracelet de décharge antistatique pour éviter
d’endommager les composants électroniques. Placez les
modules dans un emballage antistatique lors du transport ou
du stockage. Lorsque vous travaillez sur les modules, placez-
les toujours sur un tapis antistatique certifié muni d’un
branchement de mise à la terre.
■dLa borne de mise à la terre du châssis doit être branchée à
une prise de terre afin d’assurer que le boîtier métallique de la
SFP est correctement mis à la terre grâce au connecteur de face
arrière.
Ce produit est conçu pour répondre aux classes environnemen-
tales suivantes :
■ETSI EN 300 019-2-1: “Classification des conditions
d'environnement; Entreposage,” Classe 1.2
■ETSI EN 300 019-2-2: “Classification des conditions
d'environnements; Transport,” Classe 2.3
■ETSI EN 300 019-2-3: “Classification des conditions
d'environnements; l'utilisation à poste fixe dans des endroits
protégés contre les intempéries,” Classe 3.2
L'équipement est conçu pour fonctionner sans dégradation lors
des tests à tous les niveaux de sévérité, suivant les spécifications
de la classe 3.2 de l'ETSI EN 300 019-1-3.
Ce produit est conforme à la directive européenne RoHS 2002/
95/CE et/ou aux exonérations applicables. Reportez-vous à
www.adtran.com pour de plus amples renseignements sur
RoHS/WEEE.
DEUTSCH
WARNUNG
!
Lesen Sie sich alle Warn- und Sicherheitshinweise durch, bevor
Sie dieses Gerät installieren oder warten.
VORSICHT
C
Dieses Produkt nutzt ein mit den Richtlinien 21 CFR 1040.10 und
1040.11 und IEC 60825-1 und -2 konformes Class 1 Lasermodul.
Damit die obigen Richtlinien auch in Zukunft eingehalten werden
können, dürfen ausschließlich Class 1 Lasermodule von einem
von ADTRAN zugelassenen Anbieter in dem Produkt installiert
werden (erhältlich auf der Website von ADTRAN). ADTRAN
garantiert nicht für die Systemintegrität bei anderen
Lasermodulen.
VORSICHT
!
■Elektrostatische Entladungen können elektronische Module
beschädigen. Tragen Sie beim Umgang mit Modulen ein
Erdungsarmband, um Schäden an den elektronischen
Komponenten zu vermeiden. Transportieren oder lagern Sie
Module in antistatischem Verpackungsmaterial. Bei der Arbeit
an den Modulen, achten Sie darauf, diese stets auf
antistatische, elektrisch geerdete Matten zu legen.
■Die Erdungsschiene des Rahmens muss an eine Bodenstation
angeschlossen werden, um sicherzustellen, dass das
Metallgehäuse des SFP vorschriftsmäßig über den
Rückwandanschluss geerdet ist.
Dieses Produkt wurde entsprechend der folgenden Umweltk-
lassen entwickelt:
■ETSI EN 300 019-2-1: “Klassifikation von Umweltbedingungen,
Lagerung,” Klasse 1.2
■ETSI EN 300 019-2-2: “Klassifikation von Umweltbedingungen,
Transport,” Klasse 2.2
■ETSI EN 300 019-2-3: “Klassifikation von Umweltbedingungen,
Stationärer Einsatz ohne Witterungseinflüsse,” Klasse 3.2
Dieses Gerät funktioniert ohne Leistungsabfall während aller für
Klasse 3.2 von ETSI EN 300 019-1-3 vorgeschriebenen Belastung-
stests.
Dieses Produkt erfüllt die EU RoHS Richtlinie 2002/95/EC und/
oder gültige Ausnahmen. Bitte besuchen Sie www.adtran.com für
ausführlichere Informationen zu RoHS/WEEE.

CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product
within the warranty period if it does not meet its
published specifications or fails while in service.
Warranty information can be found online at
www.adtran.com/warranty.
©2016 ADTRAN, Inc. All Rights Reserved. *61442480F1-22A*
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807