ADTRAN Total Access 5000 User manual

jobAid
1
DESCRIPTION
This Job Aid supports the following SFPs:
The Small Form-Factor Pluggable Active Optical Cable (MMF
SFP+ AOC) is a fully duplex serial electric/serial optical device
with both transmit and receive functions contained in a single
module that provides a high-speed serial link at 10 Gbs.
These SFP+ active optical cables are two SFP+ modules connected
with a multi-mode fiber of different lengths. Installed into appro-
priate host modules, the MMF SFP+ provides a 10 Gigabit
interface to the supporting system. The transmit side of the SFP+
converts serial non-return-to-zero (NRZ) electrical data at the 10
Gbs line rate to a standard compliant optical signal. The receive
side of the SFP+ converts the incoming DC-balanced serial NRZ
optical data at the 10 Gbs line rate into serial electrical data.
Part Number Length CLEI
1442400F1C 3 meters BVPQAFAM_ _
1442400F2C 5 meters BVPQAFBM_ _
1442400F3C 1 meter BVPQAFEM_ _
Total Access 5000
Small Form-Factor Pluggable, 9.953–
11.3G, 850 nm Multi-mode Fiber,
Limiting, SFP+
The following features are supported on the SFP+:
■850 nm optical signals are transmitted through the cable
■Case temperature hardened range from 0°C to 70°C
■Low power consumption (<1 W max)
■Bit error rate (<1x10-12)
■Excellent EMI performance
CAUTION
!
Due to compliance certification requirements, only SFP+s
supplied by ADTRAN are to be used with the host module.
ADTRAN cannot certify system integrity with other SFP+s.
Operational Specifications
■Optical Specifications:
♦850 nm optical signals
♦Data rate: 9.95 to 11.3 Gbs
♦Minimum fiber bend radius: 30 mm
■Extended Environmental Support:
♦Operational temperature range: 0°C to +70°C
♦Storage temperature range: –10°C to +70°C
♦Relative humidity to 80%, noncondensing
INSTALLATION
Before installing the equipment, inspect the SFP+ AOC. If damage
has occurred during shipping, file a claim with the carrier, and
then contact ADTRAN Customer Support. For more information,
refer to the warranty.
CAUTION
!
The connectors on the optical cable convert electrical signals from
the adapters’ copper connections into light that is transmitted
along fiber to the opposing ends, where the light is then
reconverted to electrical signals. Because the cable contains
optical fiber, care must be taken with regard to bend radius
tolerances (refer to the Operational Specifications section above).
Product P/N: See Below
Issue Date: July 2015
Document P/N: 61442400FxC-22B
Documentation for ADTRAN Carrier Networks products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following online documents and resources provide additional information for this product:
SFP/XFP/SFP+ Compatibility Matrix (online tool, go to: http://www.adtran.com/sfp)

261442400FxC-22B
SAFETY AND REGULATORY COMPLIANCE
WARNING
!
■Read all warnings and cautions before installing or servicing
this equipment.
■To provide proper airflow and protection in this system, all
chassis slots must be populated with either a module or an
appropriate blank panel. Failure to install blank panels in all
unpopulated slots will void the warranty for modules
installed in a misconfigured system.
CAUTION
C
This product is a Class 1 Laser that complies with FDA 21 CFR
1040.10 and 1040.11 and IEC 60825-1 and -2. The product is NRTL
Listed and CB Certified to all applicable American and European
safety standards.
CAUTION
!
■Electrostatic Discharge (ESD) can damage electronic modules.
When handling modules, wear an antistatic discharge wrist
strap to prevent damage to electronic components. Place
modules in antistatic packing material when transporting or
storing. When working on modules, always place them on an
approved antistatic mat that is electrically grounded.
■Per GR-1089-CORE the system is designed and intended for
installation as part of a Common Bonding Network (CBN).
The system is not designed nor intended for installation as
part of an Isolated Bonding Network (IBN).
■Per GR-1089-CORE Section 9, this product does not have an
internal DC connection between battery return and frame
ground. This product can be installed in a DC-I (isolated) or
DC-C (common) installation. For installations where other
cards or the host system have internal connections between
battery return and frame ground, the system would be
intended for deployment only in a DC-C installation.
■The chassis frame ground terminal must be connected to an
earth ground to ensure that the metal enclosure of the SFP is
properly grounded via the backplane connector.
NOTE
■The Gigabit Ethernet port(s) are optical and therefore are not
classified as any type of port as defined in Appendix B of GR-
1089-CORE.
■This product is compliant with SFF-8472 “Digital Diagnostics
Monitoring Interface for Optical Transceivers,” Revision 9.3.
■This product is compliant with the SFP Multi-Source
Agreement (MSA).
■This product is designed to be deployed in GR-3108-CORE
environmental class 1 as defined in GR-3108-CORE.
This product meets or exceeds all the applicable requirements of
NEBS, Telcordia GR-63-CORE, GR-1089-CORE, and ETSI EN
300386. This product is intended for deployment in Central Office
type facilities, EEEs, EECs, and locations where the NEC applies
(for example, Customer Premises).
This product is to be installed in ADTRAN products in Restricted
Access Locations only, and installed by trained service personnel.
To install the SFP+ AOC into an appropriate module, complete
the following steps:
NOTE
This SFP+ AOC is shipped with the connector ends of the active
optical cable already inserted into the SFP+ adapters.
1. Use standard ESD precautions when installing an AOC.
2. Ensuring that the bail release lever on the SFP+ adapter of
the AOC is properly oriented for the cage, slide the SFP+
adapter into an SFP+ cage until a connection is made and an
audible “click” is heard.
NOTE
The bail lever (latch) on the SFP+ adapter is for removal only.
3. Continue the installation and turn-up of the host module
using the instructions in the Job Aid provided with the
module or other system-level documentation available
online at www.adtran.com.
REMOVAL
To remove the SFP+ AOC from a module, refer to the following
procedures:
1. Use standard ESD precautions when removing an AOC.
2. Depress the tab on top of the active optical cable plug and
extract the cable from the SFP+ adapter.
3. Pivot the SFP+ adapter’s bail release lever to release the
adapter from the SFP+ cage.
4. Grasp the SFP+ adapter’s housing and slide it out of the
cage. Pivot the bail lever back to the closed position and
reinsert the cable plug.
PROVISIONING
The SFP+ AOC is not provisionable. For configuration or status
information, access the menu system of the host module. Refer to
the “Provisioning” section of the host module documentation for
provisioning details.
MAINTENANCE
The SFP+ AOC does not require routine hardware maintenance
for normal operation. ADTRAN does not recommend that repairs
be attempted in the field. Repair services may be obtained by
returning the defective unit to ADTRAN. Refer to the warranty
for further information. Field support for software is provided
through upgrade facilities.
SFP+ Adapter
Active Cable
SFP+ cage on host board
Label

61442400FxC-22B 3
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.
This product is designed to meet the following environmental
classes:
■ETSI EN 300 019-1-1: “Classification of environmental conditions;
Storage,” Class 1.2
■ETSI EN 300 019-1-2: “Classification of environmental conditions;
Transportation,” Class 2.3
■ETSI EN 300 019-1-3: “Classification of environmental conditions;
Stationary use at weather-protected locations,” Class 3.2
The equipment is designed to function without degradation
during exposure to all test severities per Class 3.2 of ETSI EN 300
019-1-3.
This product meets the EU RoHS Directive 2011/65/EU and/or
applicable exemptions. Refer to www.adtran.com for further
information on RoHS/WEEE.
Français
WARNING
!
■Lisez tous les avertissements et mises en garde avant
l’installation de cet équipement ou la réalisation de toute
opération de maintenance.
■Afin d’assurer une ventilation et une protection adéquates du
système, toutes les fentes du châssis doivent être comblées par
un module ou un panneau de remplissage. L’absence de
panneaux de remplissage dans toutes les fentes non occupées
entraîne l’annulation de la garantie pour les modules installés
dans un système mal configuré.
CAUTION
C
Ce produit est un laser de classe 1 conforme à la norme FDA 21
CFR 1040.10 et 1040.11 et IEC 60825-1 et -2. Le produit est NRTL
et CB certifiée à toutes les normes de sûreté américaines et
européennes.
CAUTION
!
■L'ESD (décharge électrostatique) peut endommager les
modules électroniques. Lors de la manipulation des modules,
portez un bracelet de décharge antistatique pour éviter
d’endommager les composants électroniques. Placez les
modules dans un emballage antistatique lors du transport ou
du stockage. Lorsque vous travaillez sur les modules, placez-
les toujours sur un tapis antistatique certifié muni d’un
branchement de mise à la terre.
■La borne de mise à la terre du châssis doit être branchée à une
prise de terre afin d’assurer que le boîtier métallique de la SFP
est correctement mis à la terre grâce au connecteur de face
arrière.
Ce produit est conçu pour répondre aux classes environnemen-
tales suivantes :
■ETSI EN 300 019-1-1: “Classification des conditions
d'environnement; Entreposage,” classe 1.2
■ETSI EN 300 019-1-2: “Classification des conditions
d'environnements; Transport,” classe 2.3
■ETSI EN 300 019-1-3: “Classification des conditions
d'environnements; l'utilisation à poste fixe dans des endroits
protégés contre les intempéries,” classe 3.3
L'équipement est conçu pour fonctionner sans dégradation lors des tests à
tous les niveaux de sévérité, suivant les spécifications de laclasse 3.3 de
l'ETSI EN 300 019-1-3.
Ce produit est conforme à la directive européenne RoHS 2011/
65/EU et/ou aux exonérations applicables. Reportez-vous à
www.adtran.com pour de plus amples renseignements sur
RoHS/WEEE.
Deutsch
WARNING
!
■Lesen Sie sich alle Warn- und Sicherheitshinweise durch,
bevor Sie dieses Gerät installieren oder warten.
■Zur Gewährleistung eines angemessenen Luftstroms und der
Sicherheit dieses Systems müssen alle Steckplätze im Gehäuse
entweder mit einem Modul oder geeigneten Leerblenden
belegt sein. Widrigenfalls verfällt die Garantie für alle jene
Module, die in dem nicht angemessen konfigurierten System
installiert sind.
CAUTION
C
Dieses Produkt ist ein Klasse 1 Laser, die mit FDA 21 CFR 1040.10
und 1040.11 und IEC 60825-1 und -2 entspricht. Das Produkt ist
NRTL gelistet und CB Certified allen geltenden amerikanischen
und europäischen Sicherheitsnormen.
CAUTION
!
■Elektrostatische Entladung können elektronische Module
beschädigen. Tragen Sie beim Umgang mit Modulen ein
Erdungsarmband, um Schäden an den elektronischen
Komponenten zu vermeiden. Transportieren oder lagern Sie
Module in antistatischem Verpackungsmaterial. Bei der Arbeit
an den Modulen, achten Sie darauf, diese stets auf
antistatische, elektrisch geerdete Matten zu legen.
■Die Erdungsschiene des Rahmens muss an eine Bodenstation
angeschlossen werden, um sicherzustellen, dass das
Metallgehäuse des SFP vorschriftsmäßig über den
Rückwandanschluss geerdet ist.
Dieses Produkt wurde entsprechend der folgenden Umweltk-
lassen entwickelt:
■ETSI EN 300 019-1-1: “Klassifikation von Umweltbedingungen,
Lagerung,” Klasse 1.2
■ETSI EN 300 019-1-2: “Klassifikation von Umweltbedingungen,
Transport,” Klasse 2.3
■ETSI EN 300 019-1-3: “Klassifikation von Umweltbedingungen,
Stationärer Einsatz ohne Witterungseinflüsse,” Klasse 3.3

CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
©2015 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.800.726.8663
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61442400FxC-22B*
Dieses Gerät funktioniert ohne Leistungsabfall während aller für
Klasse 3.3 von ETSI EN 300 019-1-3 vorgeschriebenen Belastung-
stests.
Dieses Produkt erfüllt die EU RoHS Richtlinie 2011/65/EU und/
oder gültige Ausnahmen. Bitte besuchen Sie www.adtran.com für
ausführlichere Informationen zu RoHS/WEEE.