AGFA Drystar 4500 Plug & Play User manual

AGFA Drystar 4500 Plug & Play
Installation manual
English Edition
Drystar 4500
User manual
Drystar 4500
Reference manual
Agfa Medical
Agfa Medical
DECLARATION OF CONFORMITY
XXXXXX XXXX XXXXXX XXXXXX XXXX XXXXXX
XXXXXX XXXX XXXXXX XXXXXX XXXX XXXXXX
XXXXXX XXXX XXXXXX XXXXXX XXXX XXXXXX
XXXXXX XXXX XXXXXX
XXXXXX XXXX XXXXXX
XXXXXX XXXX XXXXXX
XXXXXX XXXX XXXXXX
XXXXXX XXXX XXXXXX XXXXXX XXXX XXXXXX

2/18
2805F EN 20050128
The device must only be operated according to its specifications and its intended use. Any operation not
corresponding to the specifications or intended use may result in hazards, which in turn may lead to serious
injuries or fatal accidents (for example electric shock). AGFA positively will not assume any liability in these
cases.
The device must only be installed and put into operation under the specified conditions.
For more information about safety, security and use, refer to the Drystar 4500 Reference and User manual.
For more information on Agfa products and Agfa HealthCare products, please visit www.agfa.com, your Point of Knowledge.
© Agfa-Gevaert N.V. 2005.
No parts of this document may be reproduced, copied, adapted or transmitted in any form or by any means without the written permission of
Agfa-Gevaert N.V.
Agfa-Gevaert N.V. makes no warranties or representation, expressed or implied, with respect to the accuracy, completeness or usefulness of the
information contained in this document and specifically disclaims warranties of suitability for any particular purpose. Agfa-Gevaert N.V. shall
under no circumstances be liable for any damage arising from the use or inability to use any information, apparatus, method or process disclosed
in this document.
Agfa-Gevaert N.V. reserves the right to make changes to this document without prior notice.
Agfa-Gevaert N.V., Septestraat 27, B-2640 Mortsel, Belgium.
Drystar 4500 is a trademark of Agfa-Gevaert N.V., Belgium.
Agfa and the Agfa-Rhombus are trademarks of Agfa-Gevaert AG, Germany.

3/18
2805F EN 200501282805F EN 20050128
1 Contents of the packages
Drystar 4500
User manual
Drystar 4500
Reference manual
Agfa Medical
Agfa Medical
DECLARATION OF CONFORMITY
XXXXXX XXXX XXXXXX XXXXXX XXXX XXXXXX
XXXXXX XXXX XXXXXX XXXXXX XXXX XXXXXX
XXXXXX XXXX XXXXXX XXXXXX XXXX XXXXXX
XXXXXX XXXX XXXXXX
XXXXXX XXXX XXXXXX
XXXXXX XXXX XXXXXX
XXXXXX XXXX XXXXXX
XXXXXX XXXX XXXXXX XXXXXX XXXX XXXXXX
Two film packs
Set of manuals
Set of documents
Phillips screwdriver
Set of cables
1Contents of the packages.
Drystar 4500
2Required tools.
Included Not included
Wire cutter
Philips screwdriver
6 mm Allen key
Standard screwdriver 7 mm hex key
A
Unpacking

4/18
2805F EN 20050128
2 Remove the packing materials
1Remove the cardboard box.
3Remove the plastic bag.
Accessories
FRONT SIDE
2Remove the foam blocks.
4Remove the front panel protection.
5Create a descending slope.
Unpacking
A

5/18
2805F EN 200501282805F EN 20050128
3 Unscrew the fixations
1Take 6 mm Allen key.
3Unlock the wheel brakes.
MOBILE INSTALLATION
If the printer is to be installed on a van,
continue unpacking as described and refer
to the illustration when securing the printer
to the van floor.
2Remove eight screws and two fixation
bars.
MOBILE / SEISMIC INSTALLATION ONLY:
reuse the fixation bars and screws to secure
the printer at its final location.
4Pull the printer down the slope and
relock the wheel brakes.
1
2
3
1
2
3
4
1
12
2
12
A
Unpacking

6/18
2805F EN 20050128
4 Unpack the accessories
1Check all accessories.
2Check all documents.
3Return the packing materials.
Drystar4500
Usermanual
Release2.0
Drystar4500
Referencemanual
Release1.xorhigher
AgfaMedical
DECLARATIONOFCONFORMITY
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Agfa Medical
Refer to the Packing slip for
a complete list of
accessories.
Drystar4500
Usermanual
DECLARATIONOFCONFORMITY
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Drystar4500
Referencemanual
AgfaMedical
AgfaMedical
Refer to the Packing slip for
a complete list
of documents.
R
IFRED
INSPECT CONTENTS
TIPPINGHASOCCURED
MEDIARECOVERY;INCD
ALLAS;T
X
I-800-527-9497U.S.PAT.NO.4,438,720
R
IFRED
INSPECTCONTENTS
TIPPINGHASOCCURED
MEDIARECOVERY;INCDALLAS;TX
I-800-527-9497U.S.PAT.NO.4,438,720
R
Model/ModellL-65
Wood
Paper
Plastic
Metals
Unpacking
A

7/18
2805F EN 200501282805F EN 20050128
5 Environment specifications
1Environment requirements.
4Space requirements.
◆Ventilated room,
◆away from direct sunlight,
◆away from sources of dust, humidity, heat and
cold,
◆room temperature between 15°C (50°F) and
30°C (86°F),
◆relative humidity between 20% and 75% non-
condensing.
600mm
±24"
600mm
±24"
600mm
±24"
600mm
±24"
600mm
±24"
100mm
±4"
Space required for normal useSpace required for servicing and installation
2Power requirements.
3Network requirements.
◆The AC outlet must have either o
f
f
ollowing
specifications:
◆100-120 V, 60 Hz, 16/15 A,
or
◆200-240 V, 50 Hz, 16/15 A.
◆Ethernet/connectors:
RJ45 twisted pair for 10/100Base-TX;Serial
RS232 connection,
◆Network protocols (TCP/IP services):
FTP, Telnet, HTTP, SNMP, SMTP, LPD, Helios.
B
Installation

8/18
2805F EN 20050128
6 Remove the transport protection blocks
1Open the upper input tray
and the top cover.
3Close the upper tray and the top cover.
5Remove the protection foam.
1
2
3
1
2
2Remove the protection foam.
4Open the lower input tray.
6Close the lower input tray.
2
1
Installation
B

9/18
2805F EN 200501282805F EN 20050128
7 Remove the protection straps
1Open both input trays and the top cover.
3Cut the two upper red straps.
5Open the film input assembly.
1
23
4
2Take wire cutter.
4Cut the two lower red straps.
6Cut the red strap, and close the input
trays and the top cover.
B
Installation

10/18
2805F EN 20050128
8 Remove the side covers
1Open the front cover.
3Take standard screwdriver.
5Push two pins upwards and remove the
right side cover.
1
1
2
2Remove the two adhesive straps and
close the front cover.
4Unlock the quarter turn fastener.
6Remove the left side cover.
1
2
2
3
Installation
B