AJAX StreetSiren User manual

StreetSiren User Manual
Updated September 28, 2021
StreetSiren is a wireless outdoor alerting device with a sound volume of up to
113 dB. Equipped with a bright LED frame and pre-installed battery, StreetSiren
can be quickly installed, set up, and operate autonomously up to 5 years.
Connecting to the Ajax security system via the secured radio protocol,
StreetSiren communicates with the at a distance of up to 1,500 m in line of
sight.
The device is set up via the for iOS, Android, macOS, and Windows.
The system noties users of all events through push notications, SMS, and
calls (if activated).
StreetSiren operates with only and does not support connecting via
or integration modules.
The Ajax security system can be connected to a central monitoring station of a
security company.
Jeweller
hub
Ajax apps
Ajax hubs uartBridge
ocBridge Plus

Functional elements
Operating Principle
StreetSiren signicantly improves the eciency of the security system.With a
high probability, its loud alarm signal and light indication is sucient to attract
the attention of neighbors and deter intruders.
The siren can be seen and heard from far away due to the powerful buzzer and
bright LED. When installed properly, it is hard to dismount and switch off the
actuated siren: its body is sturdy, the metal net protects the buzzer, the power
supply is autonomous, and the on/off button is locked during the alarm.
Buy street siren StreetSiren
1. LED frame
2. Light indicator
3. Siren buzzer behind the metal net
4. SmartBracket attachment panel
5. External power supply connection terminals
6. QR code
7. On/off button
8. Place of xing the SmartBracket panel with a screw

StreetSiren is equipped with a tamper button and an accelerometer. The tamper
button is triggered when the device body is opened, and the accelerometer is
activated when someone’s try to move or dismount the device.
Connecting
Before starting the connection:
Only users with administrator rights can pair the device with the hub
Pairing the device with the hub:
1. Following the hub user guide, install the . Create an account, add
the hub, and create at least one room.
Ajax app
2. Switch on the hub and check the internet connection (via Ethernet cable
and/or GSM network).
3. Make sure that the hub is disarmed and does not update by checking its
status in the Ajax app.
1. Select Add Device in the Ajax app.
2. Name the device, scan or type the QR code (located on the detector body
and packaging), and select the location room.

The on/off button is recessed into the body of the siren and quite tight, you can use a
thin solid object to press it.
For detecting and pairing to occur, the device should be located within the
coverage of the wireless network of the hub (at the same protected object). The
connection request is transmitted briey: at the moment of switching on the
device.
3. Tap Add — the countdown will start.
4. Switch on the device by holding the power button for 3 seconds.

StreetSiren switches off automatically after failing to connect to the hub. To
retry the connection, you do not need to switch it off. If the device has already
been assigned to another hub, switch it off and follow the standard pairing
procedure.
The device connected to the hub appears in the list of devices in the app. The
update of the detector statuses in the list depends on the device ping interval
set in the hub settings (the default value is 36 seconds).
Please note that only 10 sirens can be connected to one hub
Icons
Icons display some of the StreetSiren states. You can view them in the Ajax app,
in the Devices menu.
Icon Value
Shows Jeweller signal strength between the hub/range extender and
StreetSiren
The recommended value is 2-3 bars
Battery charge level
Displayed if the device is working via a
StreetSiren is temporarily off
StreetSiren tamper triggering events are temporarily disabled
How battery charge is displayed in Ajax apps
ReX radio signal range
extender
Learn more
Learn more

States
Siren states can be found in the Ajax app:
Parameter Value
Temperature
The temperature of the device which is
measured on the processor and changes
gradually. Displayed in 1°C increment.
Acceptable error between the value in the app
and temperature at the installation site: 2–4°C
Jeweller Signal Strength
Signal strength between the hub/range
extender and siren.
We recommend installing the siren in places
with the signal strength of 2-3 bars
Connection
Connection status between the hub/range
extender and StreetSiren:
Battery Charge
Battery level of the device. Two states available:
Lid The tamper button state, which reacts to the
opening of the device body
External Power External power supply status of the siren:
1. Go to the Devices tab.
2. Select StreetSiren from the list.
Online — the siren is connected to the
hub/range extender
Oine — the siren is not connected to the
hub/range extender
ОК
Battery discharged
How battery charge is displayed in
Ajax apps

Alarm Volume
Volume level in case of alarm
The volume level is measured 1 m away from
the siren
Alarm Duration, sec Duration of the alarm sound’ from 3 to 180
seconds
Alert if Moved The state of the accelerometer alarm
LED indication If enabled, the siren LED blinks once every 2
seconds only when the system is armed
Beep when arming and disarming of the system
If enabled, the siren alerts you by backlighting
the LED frame and a short beep when arming
and disarming
Notify about arming/disarming of the Night
mode
If enabled, the siren alerts you by backlighting
the LED frame and a short beep when arming
and disarming the system from the Night mode
Beep on Entry/Exit delay
If this option is enabled, the siren signals about
a delay when entering/leaving (available with
firmware version 3.50 or later)
Notify about the entry/exit delay in the Night
mode
If this option is enabled, the siren beeps to
signal about an entry/exit delay in the Night
mode
Beep Volume Volume of the audible notication signal about
arming/disarming, entry/exit delay, opening
detector triggering:
Connected — external 12 V power supply is
connected to the siren
Disconnected — siren powered by pre-
installed batteries
Muted — the siren does not sound when the
alarm is raised
Quiet — 85 dB volume
Loud — 100 dB volume
Very loud — 113 dB volume
Quiet — 88 dB volume
Loud — 94 dB volume
Very loud — 112 dB volume

The volume level was measured 1 m away from
the siren
Temporary Deactivation
Shows the status of the device: active,
completely disabled by the user, or only
notications about triggering of the device
tamper button are disabled.
The option is available for StreetSiren with
rmware version 3.71 and later.
Firmware Siren rmware version
Device ID Device identier
Device No. Number of the device loop (zone)
Settings
To change the StreetSiren settings in the Ajax app:
Setting Value
First eld
Siren name that can be edited. The name of
device you can see at notications in the event
feed.
The name can contain up to 12 Cyrillic
characters or up to 24 Latin symbols
Room
Selecting the virtual room to which StreetSiren
DoubleDeck is assigned. The room name you
can see at notications in the event feed
Alarms in Group Mode Selecting the group to which the siren is
1. Select the hub if you have several of them or if you are using the PRO app.
2. Go to theDevices tab.
3. Select StreetSiren in the list.
4. Go to Settings by clicking on the .
5. Set the required parameters.
6. Click Back to save the new settings.

assigned. You can select one or all groups:
Regardless of the group selected, the siren will
respond to activation and
alarms
Alarm Volume
The siren responds to system alarms with the
selected volume:
The volume level is measured 1 m away from
the siren
Alarm Duration, sec
Determines how long the siren sounds in case
of alarm: 3 to 180 seconds for each operation.
Set in increments of 3 seconds
Alert if Moved
Alarm when the accelerometer is triggered: the
siren is triggered if you turn the body or detach
the device from the mount.
The built-in accelerometer takes 60 seconds to
remember the normal position. Do not rush to
check the performance of the function before
this time expires
LED indication LED indication of the siren settings:
When assigned to a group, the siren and its
indication are related to alarms and events
of this group
When attached to all groups, the siren and
its indication are related to alarms and
events of all groups in the system
Night Mode
Learn more
Muted — the siren does not sound when the
alarm is raised
Quiet — 85 dB volume
Loud — 100 dB volume
Very loud — 113 dB volume
Disabled— LED indication is off
Armed — LED blinks once every 2 seconds
only when the system is armed

Beep Settings
Opens the siren notication settings. A detailed
description of the settings is
Volume Test
Switches the device to the volume test mode
Jeweller Signal Strength Test
Switching the siren to the Jeweller signal
strength test mode. The test allows you to
check the signal level between the hub and
StreetSiren and determine the optimal
installation location
Signal Attenuation Test
Switching the StreetSiren to the signal fade test
mode (available in siren with rmware version
3.50 and later)
User Guide Opens the StreetSiren User Guide
Temporary Deactivation Allows the user to disconnect the device
without removing it from the system.
Two options are available:
Constantly — LED blinks once every 2
seconds regardless of the mode state
More about indication
available
below
What is Volume Level Test
What is Jeweller Signal Strength
Test
What is Attenuation Test
No — the device operates normally and
transmits all events
Entirely — the device will not execute
system commands or participate in
automation scenarios, and the system will
ignore device alarms and other notications
Lid only — the system will ignore only
notications about the triggering of the
device tamper button