Amana ACD105E User manual

English

English

English

English

English

English

English

English

English

English

English

English

English

English

English

16
1. Remove the screws which fasten
the cabinet at both sides and at
the back.
2. Slide the unit from the cabinet
by gripping the base pan handle
and pulling forward while bracing
the cabinet.
3. Insert the Frame uide into the
bottom of the cabinet.
Caution: Never expose plastic
front or grille to extreme
temperatures.
PREPARE UNIT
FOR
INSTALLATION-2
2Shipping
Screws
Install top rail with three 13/32"screws.
Slide left-hand curtain assembly
into left end of top and bottom
rails. Repeat for right-hand curtain
assembly. Fasten curtain retainer
strips to sides of outer case with
eight 13/32" screws.
ASSEMBLE
CURTAINS/TOP
RAIL
3
English
Inspect window track, sash, and sill
for its ability to support the weight of
air conditioner.
Measure width between window
moldings to ensure Instant Mount
will fit window frame. Instant Mount
models are designed for windows
wide (the detail see page 15)
Instant Mount kit supplied with unit
is designed for mounting in most
double-hung windows without
stor windows. For installation in
window frame with storm window,
modify sill by adding wood strips (not
included) to inner and outer sills. This
raises unit and eliminates
interference of storm window frame.
Mobile ho e window installation
Add wood strip (at least 1 1/2" wide)
along entire width of window sill.
Thickness of wood strip should match
height of front lip on window frame.
Fasten wood strip to sill with a
minimum of three countersunk wood
screws (not supplied with kit). This
provides a smooth surface for
mounting air conditioner.
Stor window installation
If storm window frame does not allow
adequate clearance below sill (1/2"
required), remove storm window
frame or create clearance by adding a
wood strip (at least 1 1/2" wide) along
entire wid th of sill. Fasten wood strip
to sill with at least three countersunk
wood screws (not supplied with kit).
This provides a smooth surface for
mounting air conditioner.
SILL
Wood
Strip
1/2"
Minimum
O
U
T
D
O
O
R
Storm Wi ndow
Frame
1 1/2"
Minimum
I
N
D
O
O
R
11/2"
Minimum
Wood
Strip
I
N
D
O
O
R
O
U
T
D
O
O
R
Window
Frame
Must be a minimum
of 1/2" to clear
bottom rail on unit
PREPARE
WINDOW FOR
INSTALLTION
4

17
Place outer case in window. Lower
sash until it rests behind front flange
of top rail. Bottom rail must rest
behind window sill.
Curtain assembly cut
away for clarity.
Use 3 screws(31/32") to fix the case to windows sash.
Expand both curtains to contact the
window frame. Attach each curtain
the window sash using 31/32" screws.
NOTE: To make screws easier to
drive, drill a pilot hole into sash
through clearance hole in curtains.
Top rail
Bottom rail
About
5°
INSTALL OUTER
CASE IN WINDOW
5
English

18
8
Find someone to help you
replace chassis in outer case.
Replace front panel, and grille.
(Don't forget to install the attachment
screws before replacing grille)
Caution:
For security purpose, reinstall
screws at cabinet's sides.
I portant:
Because window
sash helps keep unit in window,
make certain window sash contacts
outer case before reinstalling chassis.
RETURN
CHASSIS TO
OUTER CASE
English
Install sash bracket on top of indoor window sash
with one wood screw 31/32" to prevent raising of
window from the outside. Screw anchor directly into
side of window frame. For hard wood or metal window
frames, drill a pilot hole to start screw.
I portant:Be careful not to drill pilot hole too deep.
Add a piece of tape to the drill bit as a depth gauge.
Also stay clear of glass. Be careful not to damage the
function of the window.
Cut window seal gasket to width of window. Stuff window
seal strip between outdoor window glass and top of
indoor sash. This will stop air leakage which reduces
efficiency.
6
INSTALL SASH BRACKET
& SEAL GASKET
INSTALL
DRAIN TUBE
7
The base pan may overflow due to high humidity.
You must install the drain tube before using the
unit. Adjust the direction of the drain tube
to make it be in line with the hole in the rear of
unit; Insert the drain tube into the hole and twist
90¡ª. To drain the excess water to indicated
position, connect a drainpipe to the drain tube.
When pressing the drain tube or drainpipe into
place, apply force in the direction away from the
fins to avoid injuring yourself.