Anova D1005 User manual

1 — In Ground Support
2, 3, or 4 — Seats
(Straight or Curved)
ASSEMBLY INSTRUCTIONS
D1005 46” Round Table
D1080 46” Square Table
D1081 46” Square Table
D1135 46” Square Table
D1192 46” Round Table
D1193 46” Round Table
F1005 46” Round Table
F1019 46” Round Table
F1072 46” Octagon Table
F1074 46” Octagon Table
F1078 46” Square Table
F1080 46” Square Table
F1081 46” Square Table
F1135 46” Square Table
F1191 46” Octagon Table
TOOLS NEEDED:
Ratchet with 1/2” Socket•
Ratchet with 3/4” Socket•
1/2” Open-end or Box-end Wrench•
3/4” Open-end or Box-end Wrench•
Level•
40 — 5/16”
Washer
20 — 5/16” X 1.25”
Hex Head Bolt
ASSEMBLY:
The assembly is a two-person operation.
1. Inspect the shipping container contents for damage and to determine that all components and hardware are present.
ASI 145_O HRD88 S117
2. Locate the Inground Support and the Table
top Adapter and lay them out on the packing
cardboard or other so surfaced workspace.
3. Align the mounting holes in the Table top
Adapter with the holes in the appropriate end
of the Inground Support. Install one of the
1.375” O.D. Washers onto one of the 1/2” x
1.5” Long Bolts and insert the Bolt through both
parts, with the Bolt head on the outside surface of
the Inground Support. Install a 1.375” O.D. Washer
and 1/2” Nylon Insert Nut on the inside end of the
Bolt.
Use the Ratchet with 3/4” Socket and 3/4” Wrench
to tighten the Nuts .
Repeat this for the other two mounting holes on
the top side of the Adapter/Support assembly.
Turn the assembly over and repeat for the three
mounting holes on the other side of the assembly.
4. Determine the location for Table.
IMPORTANT: Locate underground utilities and avoid
them while digging the hole for the concrete base.
Model D1005 shown.
Tabletop shape and pattern may vary.
Seat shape and pattern may vary.
ASSEMBLY HARDWARE:
BENCH COMPONENTS:
F1192 46” Round Table
F1193 46” Round Table
F2121 46” Octagon Table
R1111I 46” Square Table
R1113I 46” Round Table
6 — 1/2-13 x 1.5”
Hex Head Bolt
14 — 1/2-13”
Nylon Insert Nut
28 — 1.375” O.D.
Washer
8 — 1/2 x 5.5”
Hex Head Bolt
1 — Tabletop
Round, Square, or Octagon
2, 3, or 4 — Seat Supports
1 — Tabletop Adapter
20 — 5/16”
Flanged Hex Nut
.562” ID Washer
Nylon Insert Nut
1.5” Long Bolt
.562” ID Washer
Tabletop Adapter
Inground Support
Tabletop Adapter
Inground Support
Packaging cardboard or
other so work surface
anovafurnishings.com
888.535.5005 tel

5. The walls of the concrete base should be vertical and smooth
to minimize the eects of frost upheaval. This can be achieved
with the use of concrete forms, such as Sonotube. Consider
extending the concrete base below the frost line. Consult a
professional for loose or unusual soil conditions.
6. Create a temporary structure that will be used to support the
Adapter/Support Assembly, at the desired height and level,
while the concrete is curing. The depth to install the Inground
Support is dependant on the application: 26.06” depth for
non-ADA installations and tables with 4 seats; 22.94” depth for
ADA compliance (for tables with less than 4 seats) to achieve
the required table clearance.
7. Fill forms with concrete and insert supports, centered in
concrete, until the Adapter/Support Assembly is supported
by the temporary structure. Allow the interior of the Inground
Support to ll with concrete up to the Drain Hole. Crown the
concrete cap to optimize drainage. Allow the concrete to cure
before attaching the Seat Support assemblies.
10/2012
8. Place one of the seats upside down on the packing cardboard or other so
work surface. Position one of the Seat Supports so the mounting holes in
the Seat Support line up with the mounting holes on the Seat Frame.
Place one of the 5/16” Washers on one of the 1.25” long Bolts and insert
the Bolt through the Seat Support and Seat Frame mounting holes. Apply a
5/16” Washer and 5/16” Nut to the end of the Bolt and tighten nger tight.
Repeat for the other three mounting holes. Aer all Bolts are installed, use
the Ratchet with 1/2” Socket and 1/2” wrench to tighten the Nuts.
Attach the remaining Seats to the remaining Seat Supports in the same
manner. Tables may have 2, 3, or 4 seats depending on the model.
Ground Level
26.06”
OR
22.94 ADA*
16.00”
30.00”
Temporary Structure
to hold the Adjuster/
Support assembly vertical
and at correct height for
application
Drain Hole
* Use the 26.06” depth
for non-ADA installations
and tables with four seats.
For tables with less than
four seats, to achieve the
required table clearance
for ADA compliance, use
the 22.94” installation
depth.
9. Aer the concrete has cured and the installation hole is backlled, position
two of the Seat Support assemblies on opposite sides of the Inground
Support. Place a 1.375” O.D. Washer onto one of the 5.5” Long Bolts and insert
the Bolt through the mounting holes of the Inground Support and both Seat
Supports. Add a 1.375” O.D. Washer and Nylon Insert Nut to the end of the
Bolt and tighten the Nut nger tight.
Repeat for the other three mounting holes in the Seat Support assemblies.
Aer all bolts are installed, use the Ratchet with 3/4” Socket and 3/4” Wrench
to tighten the Nuts. Check with a Level and adjust the seat as needed while
tightening. Install any remaining Seat Support assemblies in the same manner.
1.25” long Bolt
5/16” Washer
5/16” Washer
5/16” Nut
Cardboard
or other so
work surface
10. Position the Table top on the Table top Adapter so that the mounting
holes in the Frame of the Table top align with the mounting holes in the
Table top Adapter. Place one of the 5/16” Washers on one of the 1.25”
Long Bolts and insert the Bolt through the Table top Frame and the Table
top Adapter mounting holes. Apply a 5/16” Washer and 5/16” Nut to the
end of the Bolt and tighten nger tight.
Repeat for the other three mounting holes in the Table top and the Table
top Adapter. Aer all Bolts are installed, use the Ratchet with 1/2” Socket
and 1/2” Wrench to tighten the Nuts . Use a Level while tightening the
hardware and adjust the Table top as needed while tightening.
1.375” OD Washer
Nylon Insert Nut
5.5” Long Bolt
1.375” OD Washer
5/16” Washer
5/16” Nut
1.25” Long Bolt
5/16” Washer
Do not drag the assembled unit across any surface.•
This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to•
remove surface dirt. Do not clean with a solvent or petroleum based products.
Furniture must not be used other than for its intended purpose and should be inspected regularly for loose,•
missing, or broken hardware, and general instability.
Furniture that is damaged or appears to be unstable must be removed from service and be repaired or replaced.•
Repairs must be made using only factory authorized parts and methods.•
WARNING
CARE AND
MAINTENANCE
211 North Lindbergh Blvd.
St. Louis, MO 63141
tel: [phone]
web: anovafurnishings.com
ASI 145