Anova F3118 User manual

ASSEMBLY INSTRUCTIONS
F3118 4  Flat Bench
F3022 6  Flat Bench
F3025 8  Flat Bench
F3031 6  Flat Bench
F3034 8  Flat Bench
F3037 4  Flat Bench
F3039 6  Flat Bench
F3042 8  Flat Bench
D3022 6  Flat Bench
D3025 8  Flat Bench
D3039 6  Flat Bench
TOOLS NEEDED:
1/2” Open-end or Box-end Wrench•
Ratchet with 1/2” Socket•
Level•
8 x
5/16”
Washer
4 x
5/16”
Flanged Hex Nut
4 x
5/16” X 1.25”
Hex Head Bolt
ASSEMBLY:
NOTE: Before assembling the Nuts to the Bolts, it is recommended that a light oil or petroleum jelly be applied to the
Bolt threads.
1. Inspect the shipping container contents for damage and to determine that all components and hardware are present.
2. Place the Bench Seat upside down on the shipping packaging or other so surface to avoid scratching the product.
ASI 126J HRD5 S409
Locate one of the Bench Supports and position it
near the end of the Seat.
3. Align the mounting holes in the Bench Support
Bracket with the mounting holes in the end of
the Bench Seat Frame. Install a Washer onto one
of the provided Bolts and insert the Bolt through
both parts, with the Bolt head on the outside
surface of the Bench Seat. Install a Washer and
Flanged Nut on the inside end of the Bolt.
NOTE: Installing the Bolt in this direction reduces the
risk of scratching during use.
Leave the hardware nger tight so that
adjustments can be made during assembly and
leveling.
Install a Bolt and Washer through the other set
of mounting holes in that end of the Bench Seat
Frame and Bench Support Bracket and install
a Washer and Flanged Nut. Again, leave the
hardware nger tight.
ASSEMBLY HARDWARE:
BENCH COMPONENTS:
1 x
Bench Seat
2 x
Bench Support
Support
Bracket
Seat Frame
Washer
5/16” Flanged Nut
Washer
5/16” Bolt
packaging cardboard or
other so surface
Washer
Flanged Nut
Washer
Bolt
model F3118 shown
seat length and pattern
may vary
OR
anovafurnishings.com
888.535.5005 tel

10/2012
4. Attach the other Bench Support to the Bench Seat in the
same manner, installing the Bolts from the outside inward.
Leave the hardware nger tight.
5. Turn the Bench upright. Tighten all hardware while
checking with a Level.
6. Move the assembled Bench to the desired location.
NOTE: The foot of each Bench Support features an 8” square
plate with four .5” diameter mounting holes. Mounting
hardware, appropriate to the surface the bench will be
mounted to, must be purchased by the user. Follow any
directions provided with the mounting hardeware.
7. Retighten hardware two weeks aer initial assembly.
Washer
and Bolt Washer and
Flanged Nut
Do not drag the assembled unit across any surface.•
This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to•
remove surface dirt. Do not clean with a solvent or petroleum based products.
Furniture must not be used other than for its intended purpose and should be inspected regularly for loose,•
missing, or broken hardware, and general instability.
Furniture that is damaged or appears to be unstable must be removed from service and be repaired or replaced.•
Repairs must be made using only factory authorized parts and methods.•
WARNING
CARE AND
MAINTENANCE
211 North Lindbergh Blvd.
St. Louis, MO 63141
tel: [phone]
web: anovafurnishings.com