Anova D1147 User manual

anovafurnishings.com
888.535.5005 tel
ASSEMBLY INSTRUCTIONS
D1147 Round Picnic Table
F1146 Square Picnic Table
F1147 Round Picnic Table
TOOLS NEEDED:
Ratchet with 1/2” Socket•
1/2” Open End or Box End Wrench•
Phillips Screwdriver•
Rubber Mallet•
8 x
Plug
8 x
5/16 X 1.25” Hex Hd Bolt
ASSEMBLY:
The assembly is a two-person operation.
1. Inspect the shipping container contents for damage and to determine that all components and hardware are present.
2. Assemble the Table over the shipping packaging or padded work area to avoid scratching the product.
NOTE: Before assembling the Nuts to the Bolts, it is recommended that a light oil or petroleum jelly be applied to the screw threads.
TABLE COMPONENTS:
1 x Cross Brace
4 x Table Top Support
1 x Table Top
ASSEMBLY HARDWARE:
24x
5/16” Flat Washer
F1147 model shown
Table Top shape may vary
12 x
5/16” Flanged Nut
4 x
5/16 X 2.50” Screw
Table Top
Flanged Nut
Flat Washer
1.25” Long Bolt
Flat Washer
Table Top Support
3. Place the Table Top upside down on the shipping cardboard or other so surface.
4. Position one of the Table Top Supports next to the mounting ange of the Table Top. Align the mounting holes in the Support with
the mounting holes in the ange. Install a Flat Washer on one of the 1.25” long Hex Head Bolts and insert the Bolt through one of
Shipping cardboard or
other so surface
Table Top Support
Table Top Flange
the mounting holes in the Table Top mounting
ange and into the mounting hole in the Table Top
Support. Place a Flat Washer and Flanged Nut on
the end of the Bolt and tighten nger tight.
5. Install another 1.25” Bolt with Flat Washer through
the other set of mounting holes and secure it with a
Flat Washer and Flanged Nut.
Leave the hardware nger tight so adjustments can
be made during assembly.

Do not drag the assembled unit across any surface.•
This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to•
remove surface dirt. Do not clean with a solvent or petroleum based products.
Furniture must not be used other than for its intended purpose and should be inspected regularly for loose,•
missing, or broken hardware, and general instability.
Furniture that is damaged or appears to be unstable must be removed from service and be repaired or replaced.•
Repairs must be made using only factory authorized parts and methods.•
WARNING
CARE AND
MAINTENANCE
211 North Lindbergh Blvd.
St. Louis, MO 63141
tel: [phone]
web: anovafurnishings.com
10/2012
6. Install the remaining Table Top Supports in the same manner.
Flanged Nut
Flat Washer
Flat Washer
1.25” Bolt
Flanged Nut
Flat Washer
2.50” Long
Screw
Flat Washer
Cross Brace
Install Rubber Feet in
the two outside holes
Table Top
Support
Flanged Nut
Flat Washer
2.50” Long Screw
Flat Washer
7. Locate the Rubber Feet and install one
in each of the two outside holes on
the bottom of each of the Table Top
Supports.
Use the Rubber Mallet to set them if
necessary.
8. Locate the Cross Brace and position it in the center of the Table Top Supports so that the mounting holes in the Brace line up
with the mounting holes in the Supports.
Place a Flat Washer on the end of one of the 2.50” long Screws and insert the Screw through the Table Top Support mounting
hole and through the matching hole in the Cross Brace.
Fasten the Screw using a Flat
Washer and Flanged Nut. Leave the
Nut nger tight.
Repeat this for the remaining Cross
Brace mounting holes.
9. Turn the table Right side up.
10. Level the Table Top while tightening all of the hardware.
11. Move the Table to the location where it will be used.
12. Aer two weeks, retighten all hardware.