Anviz T5 User manual

Relaystates
J8
J9
P2
PIN Description
Function
Power
1
2
DC12V
GND
Trigger Input
Trigger Input
Door Sensor
GND
Relay
Exit Button
1
2
3
4
5
6
7
8NO
NC
COM
GND
Wiegand
Output
1
2
3
4
5
6
GND
GND
Wiegand DATA0 Output
Wiegand DATA1 Output
RS485
RS485A
RS485B
Function PIN Description
Function PIN Description
Please carefully follow this wiring diagram, If the reader gets damaged by incorrect wiring
then your warranty will be void.
3. Wiring Instruction
2. Installation Diagram
1. Package list
The interface marked with for specific models,
Please according to the practical device to wire.
J8
J9
P
2
RJ45(TCP/IP)
J8 J9 P2 RJ45 USB
Relay State
12V
12V COM
COM
Port
PIN 12 6 5 4 32 1
Function
Connector +12V GND GND GND D1 D0
Mark +12V GND
Wiegand Output
J9J8
Power Supply
GND D1 D 0 Mark
Switch Power Access control
Port
PIN 1 2 8 7 6 5 4 3 2 1
Function GND
Connector
+12V GND NO NC COM GND OPEN DOOR
Power Supply Output Controller
J8 P2
Access Control Power Supply
Switch Power Supply
Port
PIN 12 8 7 6 5 4 3 2 1
GND
+12V GND NO NC COM GND OPEN DOOR
Power Supply
P2J8
5. Access Control Reader & Controller 6. Communicate with PC
RS485B RS485A
RS485
Exit
Button
Door
sensor
Power off to unlock
Relay State
Function
Connector
Output Controller
Exit
Button
Door
sensor
4. Access Control Reader & Power Supply
Mini-USB
（Note: Please verify master card to
enable the USB communication function)
TCP/IP
Mark
Door Sensor
Power on
to unlock
+12V PUSH NO GND NCGND
+
+
+
Mark
Power on
to unlock
Door Sensor
Diode
Diode
Power off
to unlock
+12V GND
+
+
+
T5 Pro/T5
Professional Access Control Reader
Quick Guide V2.0
Anviz brand and product are trademarked and
protected under law of the United States.
Unauthorized use is prohibited.
For more information, please visit www.anviz.com, or send email to [email protected] for more help.
©2018 Anviz Global Inc. All Rights Reserved.
Reader Instruction Package Accessory Package Connector Jack
Quick
Guide
Installation Steps:
Drill holes in the wall and follow the hole position
on back panel.
Install and fix back panel, connect related cables.
Fix access control reader.
①
②
③
Important Notice
· 1 · · 2 ·
12V COM
12V COM
Relay
6
7
NO
NC
COM
8
Select either
12 volt out on
COM or voltage
free contact.
P2
P2
6
7
NO
(DC12V)
(DC12V)
NC
Relay
8
COM
RS485

Screw Hole
Power the device by DC 12V and blue LED flashes fast and Fingerprint Sensor lights with beeps.
There are 4 cards in the package: Enroll Card Delete Card User Card * 2
Delete fingerprint only: (Operation Steps show as figure 1.4)
Delete Card / Card+Fingerprint: (Operation Steps show as figure 1.5)
After registing you can continue register another user or swipe
Enroll Card save and exit.
After deleting you can continue delete another user or swipe
Delete Card save and exit.
After deleting you can continue delete another user or swipe
Delete Card save and exit.
After registered you can continue register another user
or swipe enroll card save and exit.
After registered you can continue register another user or swipe
Enroll Card save and exit.
Add Card+Fingerprint: (Operation Steps show as figure 1.3)
When place finger, Red LED flashes with long
beep means the fingerprint does not exist in the device.
When swipe card, Red LED flashes with long beep
means the fingerprint does not exist in the device.
Blue LED
flashes
Swipe Enroll
Card, begin
Swipe Enroll
Card, end
Continue to register
Swipe
User Card Swipe User Card
again, please
Underneath:
9. Operation Guide
Figure 1.2
Add Fingerprint Only: (Operation Steps show as figure 1.1)
Blue LED
flashes
Place finger Place finger
again, please
Place finger Place finger
again, please
Blue LED flashes fast
and FingerPrint
sensor lights up
Blue LED flashes fast
and FingerPrint
sensor lights up
Green LED lights up
Four short beeps
Registration Successed
Green LED lights up
Four short beeps
Registration Successed
Continue to register
Figure 1.1
Add Card Only: ( Operation Steps show as figure 1.2)
When swipe card, Red LED flashes twice with two long
beeps means the User Card have been registered.
When swipe card, Red LED flashes twice with two long
beeps means the User Card have been registered.
Figure 1.3
Continue to delete
Figure 1.4
Red LED flashes
Red LED flashes fast
Continue to delete
Figure 1.5
8. lllustration for placing finger
LED
Card Reader Area
There are three colours
for device status: Red,
Blue and Green.
Swipe the card here.
Fingerprint Sensor
Place the finger here.
Swipe Enroll
Card, end
Swipe Enroll
Card, begin
Swipe User Card
again, please
Red LED flashes
fast and FingerPrint
sensor lights up
Red LED flashes
fast and FingerPrint
sensor lights up
Green LED lights up
Four short beeps
Delete Successed
Green LED lights up
Four short beeps
Delete Successed
Swipe Delete
Card, end
Swipe Delete
Card, end
Swipe Delete
Card, begin
Swipe Delete
Card, begin Swipe
User Card
37mm
140mm
49mm
Screw Hole
Continue to register
Place finger Place finger
again, please
Blue LED
flashes
Swipe
User Card
Blue LED flashes
fast and
FingerPrint
sensor lights up
Blue LED flashes
fast and
FingerPrint
sensor lights up
Green LED lights up
Four short beeps
Registration
Successed
Swipe Enroll
Card,end
Swipe Enroll
Card, begin
7. Reader Appearance
Correct method:
Incorrect method:
Place finger in the center of
the sensor.
Place finger flatly and smoothly
on the sensor.
Finger not placed on the
center of the sensor.
Finger placed inclined. Use of fingertip.
Power On:
Delete User:
User registration :
When place finger, Red LED flashes with two long beeps
means the finger have been registered.
Notice:
Notice:
Notice:
Notice:
Notice:
10. Function button
The operation will not delete any user data stored in the device.
Press the button until heard beeps, that eliminate Enroll Card and Delete Card information
in the device. After that
MUST register management cards (Enroll Card and Delete Card) to
run the machine.
Figure 1.6
Green LED lights
Four short beeps
In orginal state
Blue LED flashes Red LED lights Green LED lights
Four short beeps
Swipe Enroll
Card Swipe Delete
Card
Function Button
Register Management Cards (Enroll Card and Delete Card)
Notice:
· 3 · · 4 · · 5 ·
Function
Button