3.4.2. Transferring an call to another handset
You can transfer an internal or external call to another handset.
Answer the call.
Press INT/OK key and then a handset No.
Hang up the handset to disconnect the call and transfer the call to the called handset
The call has now been transferred.
3.5. Changing the speaker volume
The volume of the speaker or handset receiver can be changed via the volume control keys during
conversation.
The volume can be changed in 9 levels.
3.6. Deactivating the microphone (Mute)
It is possible to deactivate the microphone during a conversation:
Press Clear key to mute the microphone.
Press Clear key again to activate the microphone.
3.7. Last number redial
The unit saves the three last dialed telephone numbers in the redial memory.
You can enter the Redial list bypushing REDIAL key in the stand-by mode.
Scroll through the Redial memory by pushing REDIAL key.
When the desired number appears on the display, lift the handset.
The number will be dialed automatically.
Press Clear key for 2 seconds to escape the redial list if you don’t want to make a call from the
list.
3.8. Calling a number out of the Caller List
The unit saves the telephone numbers of the last 10 missed calls in the caller list.
This feature is only available if the telephone number of the incoming call has been sent via the
network service.
Press UP/DOWN key when the unit is in standby mode.
Select CALLER ID by using the UP and DOWN keys and press INT/OK key
Scroll through the Caller List by using the UP and DOWN keys.
When the desired number appears on the display, lift the handset.
The number will be dialed automatically.
3.9. Memory dial M1~ M6
There are six memory dial (speed dial) available.
Press UP/DOWN key when the unit is in standby mode..
Select MEMORY DIAL by using the UP and DOWN keys.
Press INT/OK key toconfirm.
Select MEMORY DIAL No. by using the UP and DOWN keys.
Press INT/OK key to confirm.
Enter number and pressINT/OK key to confirm.
During adding, press Clear key for 2 seconds to abort.
Repeat above to program other memory dial no.
3.10. Call Duration Display
When the External/Internal call is finished, the call duration will be visible for 3 seconds. The time is
displayed in the following format :{mm : ss}(minutes : seconds)
3.11. Out of Range
When the unit is out of the working range of the base unit or when it’s not subscribed to the base unit,
it will display “Searching…”.
4. Call Transfer, On Hold, Toggle and Three Party Conference
4.1. Call on hold (CH)
To put a call on hold during conversation, pressINT/OK key.
If you want to retrieve the call on hold, pressINT/OK key again.
4.2. Transfer External call to another handset
Make a call or after receiving incoming call, pressINT/OK key.’
Enter the internal handset No. and hang up handset to transfer the external call.
You will be disconnected but both other callers can talk together.
4.3. Brokers Call (Toggling between an internal call and an external call)
If you place an external call on hold, you can make a call to another internal handset. You can then
toggle between the first and the second call.
Put the external call on hold by pressing INT/OK key.
Enter the called internal handset No., when the call is connected, pressINT/OK key (Toggle) to switch
between both calls. One call will be placed on hold and you can talk to the other caller.
Note: If you hang up, your call will be disconnected and the other handset talking to the external caller along.
4.4. Three party conference call (Conf)
You can establish three partyconference with the other internal caller and an external caller.
Put the external call on hold by pressing INT/OK key.
Enter the called internal handset No., when the call is connected, press “#” button for 2 sec to establish
three party conference. Both handsets will start counting talking time.
Note: If during conference call you want to talk to internal caller, pressINT/OK key. External
call will be placed on hold. You can Toggle or restart conference at any time.
