Arjo AtmosAir Velaris - Plus Flex User manual

1. Left side bolster
2. Mattress connector
3. Mattress connector cavity
4. Foot bolster
5. Mattress
6. Buckles (four on each side)
7. Right side bolster
8. Cover attachment zip with zip ap
9. Non-Slip strips
10. Cable management loops
11. Handles (two on each bolster)
12. Buckles (four on each bolster)
13. Side bolster retaining straps (two at the head end,
two at the foot end)
QUICK REFERENCE GUIDE - USE
For use with Citadel Plus bed frame
1
2, 3
4
11
6
12
5
7
8
10
13
9
08.AAV.03EN_01 • 2023-11 • Page 1/5
AtmosAir Velaris - Plus Flex

Assemble the Plus Flex
Only use the Plus Flex with a Citadel Plus bed frame.
For active therapy, assemble the Plus Flex with the
AtmosAir Velaris pump.
For reactive therapy, do not connect the pump. If the
mattress is connected to the pump, disconnect the
pump tube-set connector.
1. Place the Plus Flex mattress central on the bed
frame.
2. For active therapy, hang the pump on the foot
board of the bed. For reactive therapy, go to
step 6.
3.
Place the pump power cable in the cable
management loops. If the foot bolster will be used,
leave slack in cable at the foot end of the bed.
4. Secure the cable using the locking clips.
5. Fold down the zip ap over the power cable and
loops.
WARNING
To avoid risks of tripping or strangulation,
always use the cable management for the
power cable.
SkinIQ
AtmosAir Velaris
406080 100130170210250 350 454
kg
6.
Extend the width of the left side of the
Citadel Plus bed frame fully, for instructions see
Citadel Plus IFU.
7. Make sure all mattress buckles, four on each side,
are placed on top of the extended bed frame.
8. Place the left side bolster on the edge of the
mattress, make sure that the foot print is located at
the foot end and that the handles are turned
upwards.
WARNING
To avoid risk of falling or entrapment,
make sure there is a caregiver present
on the open side of the bed frame, when
assembling or removing the bolsters.
08.AAV.03EN_01 • 2023-11 • Page 2/5

9. Align the buckles on the side bolster with the
buckles on the mattress.
10. Attach the four buckles.
11. Fold down the side bolster onto the bed frame.
Make sure the side bolster is rmly tted in the
extension and at level with the mattress.
12. Attach the side bolsters to the mattress, using the
locking clips on the retaining straps. There are two
at the foot end and two at the head end.
13. Repeat steps 6-12 for the right side bolster.
14. Extend the length of the Citadel Plus bed frame
fully.
15. Pull the tube-set connector on the pump through
the foot end gap on the right side of the bed frame.
16. Pull the mattress connector slightly out of its
cavity.
17. Press the connectors together. Make sure that the
pump tube-set connector clicks into place on both
sides (double-click).
18. Push the mattress connector back into the
mattress cavity.
19. Place the foot bolster at the foot end of the
mattress.
20. Fold down the foot bolster onto the bed frame.
Make sure that the connectors are aligned with the
square marking on the top cover of the foot bolster.
21. Reposition the zip ap.
08.AAV.03EN_01 • 2023-11 • Page 3/5

22. Lift up the foot bolster and place the power cable
in the left cavity.
23. For all bolsters, make sure:
• The bolsters are the same height as the
mattress.
• The print on the top cover is visible.
• All handles on the bolsters are on the outside.
• All buckles are securely attached to the
mattress.
• All locking clips are attached, on both the head
and foot end of the mattress.
• All zip aps are folded down, covering the zips.
24.
Place the patient at the centre of the mattress.
25. Make sure all side rails are up.
Transport mode
The side bolsters and/or the foot bolster might need
to be removed and reassembled during transport, for
example to t in an elevator.
Make sure there is a caregiver present at the open
side of the bed at all times and make sure that the
patient’s arms and feet are clear of the bolsters.
Never leave extended sides open. Retract the foot
end or the side of the bed frame once each bolster
has been removed.
Patient leaving bed
When the patient needs to leave the bed, make sure
there is a caregiver present at the open side at all
times.
WARNING
To avoid risk of falling or entrapment, make
sure that the patient is placed at the centre
of the mattress.
WARNING
To avoid risk of falling or entrapment, make
sure there is a caregiver present on the open
side of the bed frame, when assembling or
removing the bolsters.
WARNING
To avoid risk of falling when a patient is
leaving the bed, make sure there is a caregiver
present on the open side of the bed frame.
08.AAV.03EN_01 • 2023-11 • Page 4/5

Disassemble the Plus Flex
Do not leave extended sides open. For instructions on
how to retract the bed frame, see Citadel Plus IFU.
1. Lift out the foot bolster.
2. If applicable, disconnect the pump tube-set
connector.
3. Retract the foot end of the bed frame.
4. Detach the retaining straps on the left side bolster.
5. Lift up the left side bolster onto the mattress.
6. Detach the four buckles.
7. If applicable, detach the cable from the cable
management loops.
8. Retract the left side of the bed frame.
9. Detach the retaining straps on the right side
bolster.
10. Lift up the right side bolster onto the mattress.
11. Detach the four buckles.
12. Retract the right side of the bed frame.
ArjoHuntleigh AB
Hans Michelsensgatan 10
211 20 Malmö, Sweden
www.arjo.com 08.AAV.03EN_01 • 2023-11 • Page 5/5