Aseptico ADU-12DCEB Task Force Deluxe Manual

ADU-12DCEB Task Force Deluxe
Portable P eumatic De tal System
OPERATION a d MAINTENANCE
INSTRUCTION MANUAL

TABLE OF CONTENTS:
Package Contents . . . . . . . . . . . . . . . . . . . .i
Introduction . . . . . . . . . . . . . . . . . . . . . . . . .1
Setting Up the Unit . . . . . . . . . . . . . . . . . . .1
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Maintenance . . . . . . . . . . . . . . . . . . . . . . . .5
Warranty . . . . . . . . . . . . . . . . . . .Back Cover
Size: 12.5” x 17.5” x 7.5”
(32 cm x 44 cm x 19 cm)
Weight: 32.6 lbs (14.8 kg)
Power Source: 115 VAC, 60 z or
230 VAC, 50 z
Current Rating: 6.3A at 115 VAC or
4A at 230 VAC
Fuse: 115V Operation: 6.3A, 125V
Medium Time Delay
230V Operation: 4A, 250V Slo-
Blo Type
Air Source: 1/2 .P. Oil-Free
Compressor/Vacuum Pump
Water Supply Tank: 900 mL (0.95 Quart)
Waste Tank: 946 mL (1 Quart)
Vacuum: 1.35 CFM @ 4.0 In. g.
Environmental Conditions:
Intended for indoor use in an office environment of
10°C - 40°C, 10% - 90% humidity, non-condensing.
SPECIFICATIONS:
#TA-1
TA-1 Syringe Tip #AA-12A
andpiece older
Extension Arm
#AA-12CSB
Case Stand-Off
Bracket
#AA-12 VE
VE Tip Adapter
#AA-26SS
Stainless Steel
Dry Oral Cup
Available Accesso ies:
PACKAGE CONTENTS
ADU-12DCEB System Case/Control Box
ighspeed and Lowspeed andpiece Controls
TA-90D 3-Way Air/Water Syringe with Tip
NWS-8 Water Supply Tank
730068-08 Waste Container
Electric Foot Switch
Saliva Ejector Vacuum System
Remote AC Power Cord
AA-12CSB Case Stand-Off Bracket
Two (2) Extra Fuses
Shoulder Strap
Manual
P.O. Box 1548 • Woodinville, WA 98072
8333 216 th Street S.E. • Woodinville, WA 98072
International [phone] • Toll Free [phone]
www.aseptico.com • [email protected]
i
To prevent injury to people and damage to
property, please heed relevant warnings and
remarks. They are marked as follows:
WA NING: Serious injury or death may result if
ignored.
CAUTION: Damage to property or the
environment may result if ignored.
NOTE: Important additional information
and hints.
WARNING: This device has been tested and found to comp y with
the emissions requirements of IEC 60601-1-2:2001-09. These
requirements provide reasonab e protection against harmfu
e ectromagnetic interference in a typica medica insta ation.
However, high eve s of radio-frequency (RF) emissions from
e ectrica devices, such as ce u ar phones, may disrupt the
performance of this device. To mitigate disruptive e ectromagnetic
interference, position this device away from RF transmitters and
other sources of e ectromagnetic energy.
WA NING:
Device not suitable for use in the presence of
flammable gasses or gasseous oxidizers.

1
Your new Aseptico ADU-12DCEB Task Force Deluxe delivery system is one of the finest
portable pneumatic units available to the dental profession.
The self-contained ADU-12DCEB is designed for portable field use. The system features
a three-way air/water syringe, highspeed and lowspeed handpiece controls, and saliva
ejector vacuum. A pressurized water tank supplies water for handpiece coolant and
syringe. The Task Force Deluxe is powered by a switchable dual voltage oilless air
compressor.
Congratulations!
This system is engineered to provide many years of reliable service. Please read the
instructions provided in this manual to receive the best and longest service from your
Aseptico equipment.
Separate manuals may be provided to cover the operation and maintenance of
handpieces or other accessories for your unit.
SETTING UP THE UNIT:
1. Place the ADU-12DCEB Task Force Deluxe in an
upright position (the carrying handle at the top) on a
flat, stable surface.
2. Unlatch and open the case. Install AA-12CSB
Bracket to hold up case lid. (Figure 1)
3. Verify that the voltage selector insert is configured
properly by checking the voltage indicator on the
voltage selector module (Figure 2). The voltage
module is located behind the sliding panel on the
rear of the ADU-12DCEB (Figure 7, page 2). The
voltage selector insert must be installed in the “120”
position for 110V-120V 60 z operation or in the
“240” position for 220V-250V 50 z operation.
To switch the voltage configuration, disconnect
power cord and insert a small flat screwdriver under
the locking tab in the front of module. Gently
depress tab until the fuse housing releases (Figure
3, page 2). Carefully remove fuse housing to reveal
voltage selector insert (Figure 4). Pull insert out of
housing, turn it around and reinsert into housing
with proper voltage indicator facing out (See Figure
5, page 2).
ALIGN
THEN SLIDE
NOTE: Install
AA-12CSB
Bracket to
prevent hoses
from coming
out of holders
Fig. 1
Fig. 2 Voltage Selector Module
WA NING:
ALWAYS DISCONNECT POWER TO
T E SYSTEM BEFORE OPENING
VOLTAGE SELECTOR MODULE
240V Indicator 120V Indicator

2
SALIVA EJECTOR VACUUM
WATER COOLANT ON/OFF
TOGGLE SWITC
WATER COOLANT
FLOW CONTROL
ANDPIECE SELECTION
TOGGLE SWITC
SETTING UP THE UNIT..Cont’d
IMPO TANT: For 110V-120V use, check that the
fuse in use is a 6.3A medium time delay; for
220V-250V use, check that the fuse is a 4A Slo-
Blo type. User may have to change fuses
before use.
For 220V-250V use, confirm that the power cord
is correct for the country of usage and carries the
proper certifications.
Carefully reinstall fuses into fuse holder and slide
holder back into selector module (Figure 6). Apply
pressure until locking tab snaps back into
position, producing a distinct clicking sound.
WASTE
CONTAINER
CAVITRON WATER
OUTLET
ANDPIECE ON/OFF
TOGGLE SWITC
TANK PRESSURE TOG-
GLE SWITC
FOOT
SWITC
WATER
SUPPLY
TANK
Fig. 5
Fig. 3 Fig. 4
Fig. 6
FUSES LOCA ED
IN VOL AGE
SELEC OR
MODULE
3-WAY
AIR/WATER
SYRINGE
ANDPIECE
CONTROLS
OLDER BAR
AA-12CSB
BRACKET
VOLTAGE
SELECTOR
MODULE
& FUSE
OLDER
LOCATION
SLIDING
PANEL
Fig. 7 (Rear View)

3
OPERATION:
FOOT SWITCH
All Task Force Deluxe system components are
activated by the on/off foot switch. The foot switch
enables the operation of the handpieces, saliva
ejector and the 3-way air/water syringe.
COMP ESSED AI SUPPLY
The ADU-12DCEB contains a 1/2 P compressor/
vacuum pump that powers all functions. The
compressed air supply and vacuum are available
only when the foot switch is depressed.
SETTING UP THE UNIT..Cont’d
4. Place the syringe, highspeed handpiece and
lowspeed handpiece in their proper holders on the
holder bar.
5. Place the foot switch on the floor.
6. Remove the cap from the white plastic water
supply tank and fill with clean water. Reinstall the
cap and place water supply tank into retainer strap
inside Task Force Deluxe case.
7. Attach the saliva ejector hose onto the top of the
waste container by pushing in and rotating 1/4 turn
(Figure 8). Verify that the vacuum line and waste
container are properly installed. ang the saliva
ejector hose in its holder on the holder bar.
Fig. 8
O INS ALL SALIVA EJEC OR HOSE,
URN CONNEC OR 1/4 URN CLOCKWISE
CAUTION:
Releasing and depressing the foot switch within
two seconds may cause the compressor/
vacuum pump to stall and blow the fuses when
the handpiece on/off toggle switch is in the ‘OFF’
position. To prevent this, wait two or more
seconds after releasing footswitch before
depressing it again.
VACUUM LINE
WI H QUICK
DISCONNEC
TH EE-WAY AI /WATE SY INGE
The ADU-12DCEB Task Force Deluxe features a
TA-90D three-way air/water syringe with quick
change autoclavable tips. To remove a tip, press
on the locking collar surrounding the tip socket and
pull the used tip straight out of the socket (see Fig.
9). To insert a new tip, press locking collar and
push tip into socket as far as it will go. Release
collar and gently tug on tip before using to ensure
that tip is securely locked into socket.
Syringe Tip Sterilization:
1) Remove contaminated syringe tip.
2) Remove all visible signs of
contamination before autoclaving.
3) Autoclave tip at 132° C (270° F) for ten
minutes.
4) Sterilize between each patient use.
NOTE: Since only the tips can be autoclaved, it is
recommended that the Air/Water Syringe be bagged
with a disposable, single-use plastic sleeve between
each patient use.
Avoid damage to the syringe by removing the tip when
closing the ADU-12DCEB case for transportation.
NOTE
FIG. 9 DEPRESS
LOCKING COLLAR

4
HANDPIECE CONT OLS
The Aseptico ADU-12DCEB includes a manual
handpiece control system. The system includes
one highspeed control with water coolant and one
lowspeed control. The handpiece selection switch
allows the user to select highspeed or lowspeed
operation, and the handpiece on/off toggle switch
turns the selected handpiece on or off.
TANK P ESSU E TOGGLE SWITCH
Turns the pressure to the water supply tank on or
off. Turn switch off before removing water supply
tank.
WATE COOLANT ON/OFF TOGGLE SWITCH
Turns water coolant to highspeed handpiece on or
off.
WATE COOLANT FLOW CONT OL
Adjusts the flow of water coolant to the highspeed
handpiece control from off to full spray when the
water coolant on/off toggle switch is in the “ON”
position.
CAVIT ON WATE OUTLET
Provides water via standard 1/4” quick disconnect
to independent Cavitron or scaler units requiring a
water supply.
WATER COOLANT
FLOW CONTROL
WATER COOLANT
ON/OFF
TOGGLE SWITC
P ESSU IZED WATE SUPPLY SYSTEM
The Aseptico ADU-12DCEB incorporates a self
contained pressurized water system. This consists
of a 900 mL white plastic tank dispensing water
through the 3-way syringe and highspeed
handpiece control. Before removing the tank for
refilling, it must be depressurized. Turn off the tank
pressure toggle switch to release pressure in the
water system. Then unscrew the cap from tank
and fill tank with water. Screw cap back onto tank.
Sterilization of tank is recommended between
patient use.
SALIVA EJECTO VACUUM SYSTEM
The Saliva Ejector is powered by the
compressor/vacuum pump and is a self contained
oral evacuation system. It is supplied with a plastic
waste container and a saliva ejector hose.
To operate, attach the saliva ejector hose to the
top of the waste container and insert a standard
saliva ejector tip. To activate the saliva ejector,
depress the foot switch.
Waste from the vacuum system will collect in the
clear plastic waste container. When the waste
container is over 1/2 full, it must be emptied to
prevent a back-up in the system. After each use,
the vacuum system should be cleaned by running
clean water or vacuum system cleanser through
the saliva ejector hose and by thoroughly cleaning
the waste container. CAUTION: Use only NON-
foaming cleansers in the vaccum lines. Use a new
saliva ejector tip for each patient.
ANDPIECE
SELECTION
SWITC
ANDPIECE
ON/OFF
TOGGLE SWITC
CAVITRON
WATER OUTLET
TANK PRESSURE
TOGGLE SWITC
T E WATER SUPPLY TANK IS
PRESSURIZED DURING
OPERATION. DEPRESSURIZE
WATER TANK BY TURNING OFF
TANK PRESSURE TOGGLE
SWITC BEFORE REMOVAL.
WA NING:
The waste container has a ball float shutoff to
prevent accidental overflow. If the waste
container becomes full and the ball float
activates, the vacuum motor may not restart,
and could potentially blow the fuse.
Immediately empty waste container to
continue operation.
NOTE:

5
MAINTENANCE:
Because of its simple design, the Aseptico ADU-12DCEB Task Force Deluxe requires very little maintenance. Any
maintenance that is needed can be performed in minutes.
BLEEDING THE SYSTEM
If the unit will not be used for an extended period of time, or the unit might be subjected to freezing conditions, you
should bleed the system. Simply empty the contents of the water supply tank and install the cap back onto the tank.
Operate the air/water syringe and highspeed handpiece with water coolant 'on' until just air comes through the water
lines. Pack unit and store as normal.
HANDPIECE FLUSH
Flush the handpieces for about 5 seconds after every patient, and about 20 seconds at the beginning of each day.
GENE AL CLEANING
The external surfaces of the case should be cleaned using a soft cloth moistened with a mild detergent solution. Any
external surfaces of the unit that are contacted during use should be wiped down with a soft cloth moistened with a
disinfectant at the beginning of each day and between each patient use.
As described in the vacuum section, the saliva ejector vacuum system should be thoroughly cleaned after each use.
WATE LINES
Disinfect the water lines weekly. Prepare a 1:10 bleach solution (1 part household bleach to 10 parts water). Remove
water reservoir and discard residual water. Replace empty water supply tank and air purge all waterlines. Fill water
supply tank with bleach solution. Run bleach solution through all lines. Allow bleach solution to stand in lines for 10
minutes. Remove water supply tank and discard bleach. Flush water supply tank and all lines thoroughly
with clean water. Air purge and leave lines dry until next clinical use.
Problem:
Unit will not start
Unit starts but blows fuse
No water pressure
Insufficient vacuum
Insufficient handpiece operation
Correction:
Check console to power connection.
Depress foot switch for operation.
Check that voltage selector module is set for source voltage.
Check fuse. If blown, replace with 6.3A/125V medium time delay fuse for 110V-120V
operation, or a 4A/250V slo-blo fuse for 220V-250V operation.
Check that voltage selector module is set for source voltage.
Check vacuum waste container. If full, immediately empty to continue operation.
Check vacuum hose assembly for blockage. NEVER install a vacuum valve with a
shut-off control.
Depressurize water supply tank by turning off tank pressure toggle switch.
Check that fuse is correct for source voltage.
Check water supply tank for water level and verify that cap is tight.
Turn tank pressure toggle switch “ON”.
Depress foot switch for 5+ sec. to pressurize supply tank.
Turn water coolant flow knob counterclockwise to open.
Check vacuum waste container. If full, immediately empty to continue operation.
Check vacuum hose assembly for blockage. NEVER install a vacuum valve with a
shut-off control.
Check that waste container lid is properly seated and tightly secured.
Check that handpiece ON/OFF toggle is “ON”.
Check that handpiece “SELECT” toggle is set to desired handpiece.
Check that handpiece tubing is untangled and not crimped.
Check handpiece connection for missing gasket.
TROUBLESHOOTING:

Aseptico warrants its products against defects in material or workmanship for a period of two
(2) years, from date of original invoice. Some handpieces are warranted for one year under
the same conditions. Other handpieces and expendable components, such as air turbines
and light bulbs, are covered by shorter warranty periods, or have no warranty. Aseptico's
sole obligation under product warranty is (at its sole option and discretion) to repair or
replace any defective component or product in part or whole. Aseptico shall be the sole
arbiter of such action.
In the event of alleged defect under warranty, the purchaser is to notify Aseptico's Customer
Service Department promptly. Customer Service will provide instructions, usually directing
that the product be returned for service. Shipment to Aseptico and the cost thereof is always
the responsibility of the purchaser.
Accidental misuse, inappropriate installation, or failure to perform directed maintenance
voids the warranty. Deliberately defacing, modifying, or removing the serial number voids the
warranty.
Aseptico does not assume, under this warranty, any risks or liabilities arising from the clinical
use of its products, whether or not such use involves coincidental utilization of products
manufactured by others.
P/N: 420638
Rev. G
ECO 14073
02/2017
WARRANTY
PRINTED IN
T E U.S.A.
P.O. Box 1548 • Woodinville, WA 98072
8333 216th Street SE • Woodinville, WA 98072
[phone] • [phone]
www.aseptico.com • [email protected]