Assa Abloy Sargent Profile G1 Series User manual

Installation Instructions For
Profile Series v.G1 Cylindrical Lock
A7755A
Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
FOR ASSISTANCE, CONTACT SARGENT AT 800-727-5477 or www.sargentlock.com
A7755A.indd 1 11/9/18 12:05 PM

800-810-WIRE (9473) • www.sargentlock.com • A7755A
Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Table of Contents
Warning
General Description............................................................ 1
Specifications ..................................................................... 1
Features ............................................................................. 1
Parts Breakdown ...............................................................2-3
Installation Instructions......................................................4-9
Operational Check............................................................. 10
Installation of RF Technology Lock (G1-TU, G1-TA, G1-TP)
10
Page
1
2
3
4
5
6
7
8
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorientorrelocatethereceivingantenna
• Increasetheseparationbetweentheequipmentandreceiver
• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected
• ConsultthedealeroranexperiencedTVtechnicianforhelp
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme avec la norme NMB-003 du Canada.
Warning
1Warning:Changesormodificationstothisunitnotexpresslyapprovedbytheparty
responsible for compliance could void the user’s authority to operate the equipment.
Warning
!To comply with “Fire Listed” doors, the batteries must be replaced with alkaline batteries only.
A7755A.indd 2 11/9/18 12:05 PM

1
800-810-WIRE (9473) • www.sargentlock.com • A7755A
Profile Series v.G1 Cylindrical Lock
Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
General Description
2
Specifications
Features
3
4
•Latch – 1/2” standard
3/4” throw fire-rated double doors
  (optional)(41-prefix)
•Deadlocking latch
•Outside lever controlled by keypad,
or key retracts latch
•Inside lever retracts latch
•Locks furnished for 1-3/4” doors only
•U.L. Listed
The SARGENT Keypad Cylindrical Lock is designed for areas which require stand alone authorized entry. It is
a self-contained microprocessor-controlled keypad with non-volatile memory. The keypad will hold a total of
100(LK)/2000 (G1-LU, G1-PK, G1-PA, G1-TU, G1-TP, G1-TA) different user codes. User codes “01” & “02” are
utilized for Master Code and Supervisory Code, respectively.
Thisproductisoperatedbysix(6)“AA”alkalinebatteries.
• Nonvolatilememory
• Motordriven,batteryoperated
• Batteryoperatedwith6“AA”Alkaline
• Lowbatteryalert–4chirpsaftercodeentry
• Externalremote“requesttoenter”
• Master,EmergencyorSupervisorycodewillunlock 
 doorwhenlowbatteryhasexpired
•100(LK)or2000(G1-LU,G1-PK,G1-PA,G1-TU,
G1-TP, G1-TA) users
•ProgrammingdoneatkeypadorwithaPDAusing 
SofLink™ Plus software and a PC (G1-TA & G1-TP
require software)
• RFFobandProximityCard,Tag,Fobareoptional
• Operatesutilizinganytwotosixdigitspercode.Digits
may be repeated and codes may start with zero
• Cylinderoverride
• EntryofthreewrongUserCodesdisablesallcodes 
for ten seconds. Yellow LED on solid
• Piezohorncanbeheardwitheachkeystrokeor 
turned off by Master or Supervisory Code
• Last15transactionscanbeoutputtoportable 
print via infrared link (LK Only)
• Last2000(ExceptLK)transactionscanbeoutputto 
PC via SofLink™ Plus Software
A7755A.indd 1 11/9/18 12:05 PM

2800-810-WIRE (9473) • www.sargentlock.com • A7755A
Profile Series v.G1 Cylindrical Lock
Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
1
17
21
Optional
21
21
10
11
13
15
6
2
7
12
18, 24
16
9
14
7
21
3
25
23
5
24
19 4
5Parts Breakdown
A7755A.indd 2 11/9/18 12:05 PM

3
800-810-WIRE (9473) • www.sargentlock.com • A7755A
Profile Series v.G1 Cylindrical Lock
Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
5Parts Breakdown (Continued)
ITEM PART No. DESCRIPTION REQ’D
1 10-2000 2-3/4” Backset Latch (Standard) 1
10-2053 3-3/4” Backset Latch (23 Prefix) 1
10-2058 5” Backset Latch (25 Prefix) 1
10-2634 3/4” Throw (41 Prefix) 1
2 10-3026 Outside Escutcheon Key Pad, Key Pad/Prox (LK) 1
10-3130 Outside Escutcheon Key Pad, Key Pad/Prox (G1-LU, G1-PK, G1-TU, G1-TP) 1
10-3131 Outside Escutcheon Prox Only (G1-PA, G1-TA) 1
10-3016 Outside Escutcheon Housing Only 1
52-2432 Keypad/Proximity Bezel Assembly w/ Harness (LK) 1
52-2704 Key Pad/Proximity Bezel Assembly w/ Harness (G1-LU, G1-PK, G1-TU, G1-TP) 1
52-2706 Prox Only Bezel Assembly w/ Harness/(G1-PA, G1-TA) 1
3 10-3020 Inside Escutcheon and 100 User Controller (LK) 1
10-3126 Inside Escutcheon and 2000 User Controller (G1-LU) 1
10-3127 Inside Escutcheon and Key Pad/Prox or Prox Only Controller (G1-PA, G1-PK) 1
10-3015 Inside Escutcheon Housing Only 1
52-2439 100 User (LK) Key Pad Controller Assembly 1
52-2733 2000 User (G1-LU) Key Pad Controller Assembly 1
52-2734 2000 User (G1-PA, G1-PK) Prox Only or Prox Key Pad Controller Assy. 1
52-2736 2000 User (G1-TA, G1-TP) Prox Only or Prox/Keypad Controller Assembly w/ RF Technology
52-2735 2000 User (G1-TU) Keypad Controller Assembly w/ RF Technology
4 10-0523 “B” Inside Lever/Passage 1
10-2204 “J” Inside Lever/Passage NOTE: Coastal Levers & Cylinders other than Standard— See 10 Line Parts Pages
1
10-0501 “L” Inside Lever/Passage 1
10-0545 “P” Inside Lever/Passage 1
10-0534 “B” Inside Lever (75- Handicap Warning) 1
10-2245 “J” Inside Lever (75- Handicap Warning) 1
10-0512 “L” Inside Lever (75- Handicap Warning) 1
10-0556 “P” Inside Lever (75- Handicap Warning) 1
5 52-2437 Battery Cover Only 1
52-2509 Battery Cover RF Technology (G1-TU, G1-TP, G1-TA)
6 10-0019 Cylinder Spacer 1
7 10-0792 Spacer Bushing 2
9 10-3048 Inside Rose Spring Assembly 2
10 10-0524 “B” Outside Lever Standard Cylinder 1
10-2205 “J” Outside Lever Standard Cylinder 1
10-0502 “L” Outside Lever Standard Cylinder 1
10-0546 “P” Outside Lever Standard Cylinder 1
10-0525 “B” OutsideLever (30- To Accept Schlage Cylinder) 1
10-2206 “J” Outside Lever (30- To Accept Schlage Cylinder) 1
10-0503 “L” Outside Lever (30- To Accept Schlage Cylinder) 1
10-0547 “P” Outside Lever (30- To Accept Schlage Cylinder) 1
10-1535 “B” Outside Lever Standard Cylinder (76- Handicap Warning) 1
10-2246 “J” Outside Lever Standard Cylinder (76- Handicap Warning) 1
10-0513 “L” Outside Lever Standard Cylinder (76- Handicap Warning) 1
10-0557 “P” Outside Lever Standard Cylinder (76- Handicap Warning) 1
11 Key (Provided with Cylinder)
12 10-3049 Outside Rose Spring Assembly 1
13 13-3266 Cylinder (Standard) 1
13-3613 Schlage (SC) Cylinder (95-(SC)) 1
13-3614 Schlage (SE) Cylinder (95-(SE)) 1
10-0019 Schlage (SC, SE & Signature) Cylinder Spacer 1
13-3491 Cylinder (22-Construction) 1
13-3713 Cylinder (10-Signature) 1
13-3871 Cylinder (10-21 Signature Construction) 1
13-3944 Cylinder (21-Cylinder) 1
18-4020 Cylinder (VA-ASSA V10) 1
18-4063 Cylinder (VS-ASSA V10) 1
14 01-9170 Screws for Through-Bolts (#10-32 x 1-3/4”) 1
15 10-0312 Cylinder Retainer - All Cylinders except Removeable and Interchangeable core 1
10-0313 Cylinder Retainer - Removeable Core or Interchangeable Core 1
16 10-2642 77 Lock Body (Std, 10, 21, 23, 30, SC, SE, VA & VS Prefixes only) 1
10-2643 77 Lockbody (60, 63, 64 Prefixes only) 1
10-2644 77 Lockbody (70, 72, 65-73, 65-73P Lockbody) 1
17 08-0312 #800 Strike 1
08-0066 #808 Strike (28-Prefix) 1
18 52-0033 Fire Stop Plate and Screws (2) 1
19 45-1340 Flat Head Screw (Security) 1
 20 52-2300 ScrewPack(includesitem#’s18, 19, 24, 25) 1
01-0297 1/8” Security Socket Allen Wrench (item 24) 1
21 10-2052 Screw Pack – Specify Finish (Strike Screws, Latch Screws, Push Pin Tool, Strike Box) 1
23 52-0253 Battery Keeper 1
52-0344 Battery Keeper – RF Technology (G1-TU, G1-TP, G1-TA)
24 See Item # 20 Screw Pack
25 See Item # 20 Screw Pack
NOTE: Coastal Levers & Cylinders other
than Standard See 10 Line Parts Pages
A7755A.indd 3 11/9/18 12:05 PM

4800-810-WIRE (9473) • www.sargentlock.com • A7755A
Profile Series v.G1 Cylindrical Lock
Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Left Hand
Hinges Left.
Open inward.
“LH”
Left Hand
Reverse Bevel
Hinges Left.
Open Outward
“LHRB”
Right Hand
Hinges Right
Open Inward.
“RH”
Right Hand
Reverse Bevel
Hinges Right.
Open Outward.
“RHRB”
View lock body from top and from the outside (as shown above)
Bevel
Latchbolt Right Hand Right Hand
Reverse Bevel
Left Hand
Reverse Bevel
Lock Body
Verify hand and bevel of door
Connector and Wires
Deadbolt
Guardbolt
Latchbolt
Front
Top
Lock w/cylinder
Override
(Shown)
End Cap
Installation Instructions
6
1. Verify Hand and Bevel of Door
2. Door Preparation
Prepare door according to appropriate template
(see website www.sargentlock.com):
•For metal door template, see 4531 and 4532
•Forwooddoortemplate,seeA7456andA6719D
•Prior to installation, all holes must be free of burrs, debris
and sharp edges
• IfdoorsarenotproperlyreinforcedperANSI115.2,  
commercially available reinforcements
should be installed
Stand on outside/locked side of the door when determining the door hand
Wood Door Preparation
1-1/2"
(2) 1/8" Dia. holes x 1/4" Deep
required
7/8"
Through-bolt
hole (2)
C
L of
1-1/2" Dia.
1-1/2"
(2) 1/8" Dia. holes
required
7/8"
Fire
stop plate
Through-bolt
hole (2)
(2) Self tapping
screws #8 x 1/2"
long for wood
& metal doors
Slot
C
L of
1-1/2" Dia.
Lockbody
hole
Latchbolt
door prep
Pre-drill
and/or tap
holes (2)
Inside
of door Outside
of door
Hole for ribbon
cable from keypad
to controller
A7755A.indd 4 11/9/18 12:05 PM

5
800-810-WIRE (9473) • www.sargentlock.com • A7755A
Profile Series v.G1 Cylindrical Lock
Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
3. Frame Preparation for Strike
Non Fire Rated Exterior Doors–
Install Weather Conduit (P/N 52-2847)
as shown below
4. Latchbolt and Fire Stop Plate Installation
1. Install latch with beveled bolt facing the strike.
2. Attach with two screws but DO NOT tighten completely at this time.
3. Attach Fire Stop Plate with two screws.
Note: Required for all Fire Rated doors
Centerline of
latch front and
strike
Screws (2)
#8-32x3/4”
1-1/2"
(2) 1/8" Dia. holes x 1/4" Deep
required
7/8"
Through-bolt
hole (2)
C
L of
1-1/2" Dia.
1-1/2"
(2) 1/8" Dia. holes
required
7/8"
Fire
stop plate
Through-bolt
hole (2)
(2) Self tapping
screws #8 x 1/2"
long for wood
& metal doors
Slot
C
L of
1-1/2" Dia.
Lockbody
hole
Latchbolt
door prep
Pre-drill
and/or tap
holes (2)
Inside
of door Outside
of door
Hole for ribbon
cable from keypad
to controller
Lockbody
hole
Latchbolt
door prep
Pre-drilled
and/or tapped
holes 2 places
Inside
of door
Hole for ribbon
cable from keypad
to controller
Fire Rated Doors– Install Fire
Stop Plate (P/N 52-0033)
as shown below
IMPORTANT: Latch bevel must match door bevel and
deadlocking latch must stop on strike when door is closed
Strike
A7755A.indd 5 11/9/18 12:05 PM

6800-810-WIRE (9473) • www.sargentlock.com • A7755A
Profile Series v.G1 Cylindrical Lock
Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
For wood
door only
Screws partially
tightened
Plate
Tab
Lock
body
For wood
door only
Screws partially
tightened
“Long-mark”
(13/4" door)
should line up
with edge
of lockbody
Slot
(2 Sides)
Outside of
door
Inside of
door
Plastic
hex wrench
(provided)
Lock Preset to:
• Through-boltlocation–12&6o’clock
• Doorthickness–1-3/4”thick-seebelowforotherdoorconditions
Adjustment for different through-bolt and door thickness:
• Through-boltlocation–rotateoutsiderosetomatchdoor
• Doorthickness–rotateoutsiderosetoaligndoorthicknessmarkingwithlockbodyedge
• Spacerbushing–removeandrealigntofitintobackoflever
5. Lock Installation
IMPORTANT:
Door must remain open
during installation.
Use door stop.
IMPORTANT
Lockbody
must be
centered
in the door
3
1-3/4" thick door
2" thick door
Through-bolt
holes
Rotate to match
through-bolt holes in door
Spacer bushing
1. Feed wires into the lock body hole, from outside of door.
2. Lock body into cross-bore hole from outside of the door (locked side).
3. Lock body must engage both the latch unit prongs and tail piece, as shown.
A7755A.indd 6 11/9/18 12:05 PM

7
800-810-WIRE (9473) • www.sargentlock.com • A7755A
Profile Series v.G1 Cylindrical Lock
Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
1. Insert key, rotate 45° clockwise and hold
2. Depress lever retainer with push pin tool (provided).
7. Remove Outside Lever Only
1. With outside lever in hand- use standard
pliers, pull out cylinder retainer.
2. Remove key and cylinder from lever.
3. Insert new cylinder.*
4. Secure by pressing cylinder retainer
flush with self.*
* NOT SHOWN
How to Change Cylinder
(if required)
45º
Feed wires and
connector in
routed channel
Routed channel for
wood door only
Screws
partially
tightened
Inside of
door
Outside of
door
Feed wires and
connector if
wood door Routed channel for
wood door only
Inside nut
Inside plate
Screws
partially
tightened
1A. If wood door, feed wires up through
the routed channel as shown.
1B. If metal door, feed wire and connector
through inside of door and out hole on
outside of door. *
2. Attach inside rose assembly and
spacer bushing and secure with
screws shown
6. Securing the Lock to Door
Washers
(only 30- prefix)
Cylinder
Retainer
Cylinder
Outside
Lever
Key
A7755A.indd 7 11/9/18 12:05 PM

Outside of
door
Ground
wire
Inside lever
Inside
of door
Inside rose
8-32 Flat head
screw
Weather
Seal
Gasket
(C) Lockbody
harness
(E) Keypad
harness
(A)
Ground
wire
Latch
screws
(F) Controller
connector
Latch
screws
Cylinder
spacer
Ribbon
cable with
connector
Outside
Escutcheon
Fire stop
plate
Weather
seal gasket
8800-810-WIRE (9473) • www.sargentlock.com • A7755A
Profile Series v.G1 Cylindrical Lock
Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
NOTE: For exterior applications, use weather seal gasket part
# (10-0649) between escutcheon and outside door surface
1A. For fire rated doors only feed ribbon cable connector and
ground wire from outside of door through weather seal gasket
(if used) then fire stop plate.
1B. For non-fire rated doors only, feed ribbon cable connector
and ground wire from outside of door through weather seal
gasket (if used), then conduit sleeve in door (not shown).*
2. Slide the outside escutcheon over the lock, and hold
the escutcheon to the door surface
3. Verifywhiteplasticcylinderspacerisinsertedintohorizontal
slot of lockbody.*
4. Slide the outside lever onto tube with key horizontal
(toward latch). Rotate key 45 degress clockwise.
5. Push lever until lever catch is engaged
Outside of
door
Ground
wire
Inside lever
Inside
of door
Inside rose
8-32 Flat head
screw
Weather
Seal
Gasket
(C) Lockbody
harness
(E) Keypad
harness
(A)
Ground
wire
Latch
screws
(F) Controller
connector
Latch
screws
Cylinder
spacer
Ribbon
cable with
connector
Outside
Escutcheon
Fire stop
plate
Weather
seal gasket
8. Installation of Outside Escutcheon and Lever
9. Inside Escutcheon and Lever
1. Remove black battery cover from the escutcheon with security wrench (provided).
2. Connect ground wire to terminal E3 (Fig. 1), connect keypad harness (Fig. 2) to controller, and connect lock
body motor harness (Fig. 3) to motor connector.
3. Feedallexcesswirethroughinsidedoorholeand/intooutsideescutcheoncavity,beingcarefulnottopinch
wires.
NOTE: Connectors go on only one way, do not offset connector and be sure they are completely sealed.
4. Insert two #8-32 screws (Fig. 2) through top and bottom of inside escutcheon and thread into outside escutcheon.
Straighten escutcheons and tighten securely, being careful to avoid pinching wires.
NOTE: For RF Technology versions (G1-TU, G1-TP, G1-TA), refer to Section 8 to install through-bolt screws.
5. Slide the Inside Lever onto the tube.
6. Tightentwolatchscrewscompletely.
Figure 1
Figure 3
Figure 2
* NOT SHOWN
A7755A.indd 8 11/9/18 12:05 PM

9
800-810-WIRE (9473) • www.sargentlock.com • A7755A
Profile Series v.G1 Cylindrical Lock
Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Security
screw
Security tool
01-0297 included
Inside of
door
Battery
cover
Battery
keeper
4. Install battery keeper clip by
inserting tabs into top slots.
Push bottom in and snap into
place. Then tighten screw (Fig. 3).
5. Attach battery cover to inside
escutcheon making sure to line
up tabs with retaining slots in
battery cover. Secure with
security screw (Ref. Fig. 4).
-
+
-
+
-
+
-
+
+
-
+
-
Security
screw
Security tool
01-0297 included
Outside of
door
•
Front plate
(2) Flat head screws
3. Place (6) “AA” batteries into the
compartment being careful to
align polarity properly
(Ref. Fig. 2).
Inside of
door
Battery
cover
Battery
keeper
Lockbody screws
- Polarity
+ Polarity
Top tab
Tabs
Retaining
slots
Note: For RF Technology
version refer to Section 8
to install battery
keeper.
11. Battery Installation Fig. 1
Fig. 3
Fig. 2 Fig. 4
2-FRONT
Screws (2)
10-32 x 1-1/4"
Screws (2)
#6 x 3/4"
Scalp to be removed with flat
bladed screwdriver at notch
Test
for proper
operation
before
closing
door
For RF Technology
version, see Section
8 to install Battery
Keeper
A7755A.indd 9 11/9/18 12:05 PM

10 800-810-WIRE (9473) • www.sargentlock.com • A7755A
Profile Series v.G1 Cylindrical Lock
Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Operational Check
7
Installation of RF Technology Lock
8
For devices with cylinders:
1. Insert key into cylinder and rotate.
2. The key will retract the latch. Key should rotate freely
3. Inside lever retracts latch and deadbolt (if provided)
4. Enter 1234* to unlock outside lever handle and retract
latch and deadbolt (if provided)
5. Iflockisproxonly(G1-PA)orRFTechnologywithProx
(G1-TA) - refer to Keypad programming instruction
manual(A7716)
Outside of
door
The RF Technology Lock (G1-TU, G1-TA, G1-TP) is installed as described in
sections1-7withthefollowingexceptions:
• Installation of the top through-bolt screw
• Removal process for the battery keeper
The antenna board must be carefully moved to access the upper
through-bolt screw. Care should be taken to prevent damage to
the antenna retaining tabs during this process.
Press the two tabs away from the antenna board and lift the
board off the mounting posts. Insert the flat head through-bolt
and secure the escutcheon in place. After tightening the top
through-bolt, replace the antenna board by placing it on the
mounting posts and pressing into the retaining tabs.
A. Installation of the top through-bolt screw:
To remove the battery keeper, a flat bladed screwdriver or similar tool must be used.
Insert the screwdriver into the slot at the top of the battery keeper, lift up and pull the top of the keeper away from
the batteries.
To install, insert the tabs on the bottom of the keeper into the battery compartment slots and press the keeper
tightly against batteries.
B. Removal procedure for the Battery Keeper:
Flathead through-bolt
Antenna
Board
Retaining
Tabs
Mounting
Posts
Controller
Assembly
Insert screwdriver tip
and lift up
Battery
keeper
Tip out
Keeper tabs
A7755A.indd 10 11/9/18 12:05 PM