Assa Abloy Yale Assure Lock Lever Technical specifications

P/N YRL-LPBINSTL-FUL Rev C
1
® ®
Yale Assure Lock Lever Push Button
Installation and Programming Instructions
(YRL216)
#7 wood & #8-32
machine x 20mm
Combination screws
x4
M4 x 22mm
Pan head machine
screws
x2
#8-32 x 5/16"
Machine screws
x2
Optional
Network Module
Battery Cover
Key
AA Alkaline
Batteries
Latch
Strike Plate
Interior Mounting Plate
Interior Lock
Battery Cover
Template
Keys
Levers
Cylinder
®
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DAMAGE TO THE PRODUCT AND VOID THE FACTORY WARRANTY
Before you begin
for step-by-step installation
instructions & to register
your product
DOWNLOAD
THE BILT APP
WARNING
This product can expose you to lead which is known to the state of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65warnings.ca.gov.

P/N YRL-LPBINSTL-FUL Rev C
2
Preparing to Install
Utility Knife
Drill Wood Mortise
Chisel
Pencil Tape
Measure
Level
Tools necessary only for new
doors or adjusting existing prep.
Template
Tools Needed
Standard
Phillips Head
Screwdriver
2-3/8" through bolt posts
2-3/4" through bolt posts
Note: Adjustment based on
backset
O
optional
default
PULL
*Backset
*2-3/8" (60mm) or 2-3/4" (70mm)

P/N YRL-LPBINSTL-FUL Rev C
3
Checking Measurements
See
Door Prep
Template
2-3/8" or 2-3/4"
(60mm or 70mm)
Backset
2-1/8" (54mm)
Diameter
1-3/8" or 1-3/4"
(35mm or 44.5mm)
Door Thickness

P/N YRL-LPBINSTL-FUL Rev C
4
?Determining Door Handing
Left Hand Right Hand
Face a door swinging open
away from you.
If it swings open to the right,
it is a right hand door. If it
swings open to the left, it is a
left hand door.
Exterior
Inswinging Door
Interior Left Hand
Reverse
Right Hand
Reverse
Face a door swinging open
toward you.
If it swings open to the right, it
is a right hand reverse door. If it
swings opens to the left, it is a
left hand reverse door.
Exterior
Outswinging Door
Interior
Curve of latchbolt must contact strike plate first.
Frame
Door
Latchbolt Curve
Strike
Plate
Exterior
Interior
Outside of Door

P/N YRL-LPBINSTL-FUL Rev C
5
Preparing Door & Frame
Necessary for new doors or adjusting existing prep.
1" (25mm)
Deep
!
Drill holes 1/2 way
through door then
complete from other side
to prevent splitting.
2-1/8"
(54mm)
Dia.
2-3/8" (60mm)
or
2-3/4" (70mm)
Backset
1"
(25mm)
Dia.
See
Door Prep
Template
Inside
of Door
Frame
Frame

P/N YRL-LPBINSTL-FUL Rev C
6
x4
1Installing Latch & Strike Plate
Right Hand Installation Shown
Outside of Door
Frame

P/N YRL-LPBINSTL-FUL Rev C
7
2
Outside of
Right Hand Door
Inside of
Right Hand Door
Installing Push Button
Right Hand Installation Shown
!
!
“TOP” mark must be
on top surface and tailpiece
in vertical position.
Incorrect orientation will
cause lock to fail.

P/N YRL-LPBINSTL-FUL Rev C
8
x2
3Installing Interior Mounting Plate
Right Hand Installation Shown
Inside of
Right Hand Door
Inside of
Right Hand Door

9
4
P/N YRL-LPBINSTL-FUL Rev C
Attaching the Cable Assembly
Right Hand Installation Shown
Inside of
Right Hand Door

P/N YRL-LPBINSTL-FUL Rev C
10
5
X2
Installing Interior Lock
Right Hand Installation Shown
X
Inside of
Right Hand
Door
“Click”