Assa Abloy SARGENT 5300 Series User manual

Installation Instructions
1-800-727-5477 • www.sargentlock.com A8255A 08/19
Copyright © 2019, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited.
WARNING
This product can expose you to lead
which is known to the state of California
to cause cancer and birth defects or other
reproductive harm. For more information
go to www.P65warnings.ca.gov.
5300 Series
Alarmed Exit Devices
ATTENTION INSTALLER
Disconnect all input power before beginning installation
to prevent electrical shock and equipment damage.

2
5300 Series
Installation Instructions
Alarmed Exit Devices
A8255A 08/191-800-727-5477 • www.sargentlock.com
Copyright © 2019, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited.
TOC Table of Contents
1 General Description .............................................................3
2 Contents ........................................................................3
a Package Contents ...............................................................3
b Miscellaneous Parts .............................................................4
3 Dip Switch (SW-2, 6-position) ...................................................4
4 AL - Circuit Board ................................................................5
5 Installation Instructions .........................................................6
6 Apply Rail Assembly .............................................................7
7 Cylinder Installation .............................................................7
a Door Preparation................................................................7
b Add or Remove Cylinder.........................................................8
c Installation and Orientation of Cylinder ..........................................8
8 Alarmed Exit (5300) Standard Operating Instructions ...........................9
a Arm Alarm ......................................................................9
b Security/Tamper Violation .......................................................9
c Low Battery Alert ...............................................................9
9 Optional Features ............................................................. 10

3
5300 Series
Installation Instructions
Alarmed Exit Devices
A8255A 08/191-800-727-5477 • www.sargentlock.com
Copyright © 2019, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited.
1 General Description
The SARGENT Alarmed Exit is designed for areas that require an alarm to sound upon exiting. Once armed,
any push rail movement will activate the horn in the push rail. The horn will continue to sound for two (2)
minutes and shut off automatically. The LED will flash, indicating a violation has occurred.
Alarmed Exit
Circuitry Figure1
Manual dogging is provided standard
on non fire rated devices
2 Contents
a Package Contents
1
2
6
3
4
5
Figure2
Figure 2 Description
1 Mounting Rail, Wilde Stile
2 Chassis Assembly (Wide)
3 5300 Cover, Chassis
4 End Cap Bracket
5 End Cap
6 Pull (Sold Separately)

4
5300 Series
Installation Instructions
Alarmed Exit Devices
A8255A 08/191-800-727-5477 • www.sargentlock.com
Copyright © 2019, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited.
2 Contents (cont.)
b Miscellaneous Parts
Endcap
Mounting Plate
Exit device
chassis and rail
assembly shown
Chassis
Assembly
Cover Mounting rail insert
Figure3
3 Dip Switch (SW-2, 6-position)
Factory settings shown.
1. DS-1 = OFF, DS-2 = OFF - REX / Passage Delay
(set to 7 seconds).
2. DS-3 = OFF, DS-4 = OFF - Automatic Alarm
Reset (set to 2 minutes).
3. DS-5 = ON - Selects LED color (Armed = Green,
Violation = Red, Passage = Yellow).
4. DS-6 = ON - Monitor Relay is enabled (will
activate when rail is violated).

5
5300 Series
Installation Instructions
Alarmed Exit Devices
A8255A 08/191-800-727-5477 • www.sargentlock.com
Copyright © 2019, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited.
4 AL - Circuit Board
Printed Circuit Board:
Figure4
Note
SW-1, Arm/Disarm Switch shown in ON (armed) position.
Insert with circuit board:
Battery
Figure5
OFF
ON
1
J3
J4
J2
J1
1
1
1
SW-2 6-position
dip switch
SW-1
Arm/Disarm
switch
6 5 4 3 2 1
Figure6

6
5300 Series
Installation Instructions
Alarmed Exit Devices
A8255A 08/191-800-727-5477 • www.sargentlock.com
Copyright © 2019, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited.
5 Installation Instructions
• These instructions are for the 5300 Series exit device, which is designed for areas requiring field
selectable time delay and automatic alarm reset options.
• Verify hand and bevel of door. Exit devices are always reverse bevel and are mounted on inside of
door.
Left Hand Reverse Bevel Hinges
Left. Open Outward LHRB
Inside View Outside View Inside View Outside View
Right Hand Reverse Bevel Hinges
Left. Open Outward RHRB
LHRB Shown RHRB Shown
Figure7
5. Installation must be performed by a trained and experienced service person.
6. 9V battery operated.
7. No external wires.
Note:
For retrofit applications, refer to retrofit instructions.
Figure8

7
5300 Series
Installation Instructions
Alarmed Exit Devices
A8255A 08/191-800-727-5477 • www.sargentlock.com
Copyright © 2019, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited.
6 Apply Rail Assembly
1. Depress lift arm into rail assembly and slide rail onto chassis.
2. Attach rail assembly to chassis with two (2) #8 truss head machine screws. Do not tighten screws
(Figure9).
3. Secure chassis to door with four (4) #10 flat head screws. (Figure8)
4. Level rail.
5. Place mounting plate tight against rail and attach to door with two (2) #10 round head screws.
6. Tighten all screws securely (Figure10).
Figure9
Lift Arm Level Mounting Plate
Rail Assembly
Rail Mounting Screw (2 Places)
(#8-32 x 3/8 PH. Truss HD. Machine Screw)
Mounting Plate
Mounting Plate Screws
(#10-24 x 3/4"PH. RD. HD. Machine Screw)
Figure10
Chassis Mounting Screws
(1/4-20 x5/8 PH. FL. HD.
Machine Screws)
Four (4) places
Figure11
7 Cylinder Installation
a Door Preparation
1. Prepare door according to template.
2. Verify size 41 cylinder is installed in rail insert with collar prior to installing exit device on door.
NOTE: Use caution not to damage wires when installing cylinder nut.
Collar
Cylinder nut
Side View. Battery holder
not shown.
Use caution not to dam-
age wires when installing
cylinder nut.
Figure12

8
5300 Series
Installation Instructions
Alarmed Exit Devices
A8255A 08/191-800-727-5477 • www.sargentlock.com
Copyright © 2019, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited.
7 Cylinder Installation (cont.)
b Add or Remove Cylinder
3. Remove insert assembly from rail by sliding toward rail end.
Figure13
c Installation and Orientation of Cylinder
1. Slide cylinder through collar into insert as shown.
2. Note orientation of cylinder.
3. Secure cylinder with cylinder nut, tightening firmly.
4. Operate cylinder and verify cam is operating switch properly.
Figure14
Figure15

9
5300 Series
Installation Instructions
Alarmed Exit Devices
A8255A 08/191-800-727-5477 • www.sargentlock.com
Copyright © 2019, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited.
8 Alarmed Exit (5300) Standard Operating Instructions
a Arm Alarm
Turn key clockwise. Yellow PASSAGE LED will flash for
15 seconds (default), then a quick chirp and ARMED
green LED will flash and repeat every 30 seconds.
Signal above cylinder indicates unit is armed.
NOTE: Unit is automatically armed 15 seconds after
it is turned on. Field selectable settings listed at
bottom of page.
b Security/Tamper Violation
When ARMED, depressing the push rail will activate alarm.
Horn will sound and red violation LED will flash. The horn
will continue to sound for two (2) minutes (default).
After two (2) minutes, unit will reset on its own and red
LED will flash every 30 seconds until rearmed using the
key. Turn key counter-clockwise to deactivate alarm.
Turn key clockwise to rearm alarm.
c Low Battery Alert
Horn chirps intermittently to indicate low battery
condition. Replace 9-volt alkaline battery.
Figure16
Figure17
Figure18

10
5300 Series
Installation Instructions
Alarmed Exit Devices
A8255A 08/191-800-727-5477 • www.sargentlock.com
Copyright © 2019, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited.
9 Optional Features
Once power is connected, turn key clockwise to activate alarm. A time delay of 7, 10, 15 or 20 seconds
initiates prior to rail going into an armed state. This allows individualized alarm setting. LED will flash
yellow during this time.
Horn will chirp one (1) time. LED will flash green and repeat every 30 seconds to indicate unit is armed.
Once armed, depress push bar to sound alarm. Rail alarm will sound until disarmed using one (1) of the
following methods:
1. Rail cylinder key
2. Automatic reset (after optional field settable time delay of 2, 5 or 10 minutes)
LED will flash red every 30 seconds to indicate rail has been violated and will continue to flash red until
unit is reset manually. If battery powered and low battery voltage is detected, horn chirps quickly and
repeats every 10 seconds until battery is replaced.
These field selectable switches can change the following functions:
Auto Alarm Reset Request to Exit/Passage Time Delay
DS3 DS4 Timer Reset DS1 DS2 Timer Reset
Off Off 2 minutes Off Off 7 seconds
Off On 5 minutes Off On 10 seconds
On Off 10 minutes On Off 15 seconds
On On Continuous On On 20 seconds