Assa Abloy Yale Assure Technical specifications

Assure Lock for Andersen®Patio and Entry Doors
Installation and Programming Instructions
This manual will walk you through all the required steps to add your
new Yale Assure Lock for Andersen patio and entry doors.
Yale Assure Lock is not fully functional on Andersen 200 and 400 Series
hinged patio doors. The patio door hookbolts must be manually locked before
the Yale Assure lock can lock the patio door's deadbolt.
• Remove Existing Door Hardware
• Prepping your Door
• Install your Assure Lock
• Program your Assure Lock
• Add your Assure Lock to your smart home system or August App
Standard Phillips
Head Screwdriver
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DAMAGE TO THE LOCK
P/N YRM276/YRM476-INST-FUL Rev C
Scissors
1/8" 5/16" 3/8"
1/2" 3/4" Drill Bits
Tools needed:
Drill
AW 9184499 BA

2
P/N YRM276/YRM476-INST-FUL Rev C
Inside
Lock
4 AA Batteries
Optional
Network Module
Battery Cover
Cylinder Magnet
Block Magnet
#8x8 PHM
Handle Kit
Mounting
Plate
Battery
Cover Key
Through Bolts
Touchscreen
Spacers
Decorative Screw
What's In The Box
Door Position
Sensor

3
P/N YRM276/YRM476-INST-FUL Rev C
Remove Existing Hardware If Any
Prepping Door
Drill hole from both sides
of door; approximately 1"
deep from one side then
completely through from
other side.
Enlarge existing top hole
with 3/8" to 1/2" drill bit
to accommodate cable.
3/8" to 1/2"

4
P/N YRM276/YRM476-INST-FUL Rev C
3Preparing Inside Lock
Insert battery
removal tool
into hole to
release cover.
A spacer may be required to correctly install lock. There are three (3) options
in your lock kit. See chart to select the correct spacer for your application.
Selecting Correct Spacer
44
Door Type
Spacer Color Spacer
A-Series - Outswing Only N/A None
A-Series Inswing.
E-Series 1.75" In and Outswing
E-Series 2.25" Inswing
400 Series 1.75" Inswing
Black
200 Series 1.75" All
E-Series - 2.25" Outswing Only
Gray
White
E-Series - Architect Entrance Door and
Folding Doors Sold Separately. (Provided
when ordering thick door kit part number
AYRM-270-TDK.)
Look for product ID sticker on door. Consult Andersen for assistance.

5
P/N YRM276/YRM476-INST-FUL Rev C
Spacer Installation
5Insert spacer into hole. Push spacer in for one click.
As you continue installing lock, the spacer will tightened to required position.
Spacer is installed
between door
and mounting
plate gasket.
Do not over tighten.
Do not bend
cables. Insert one
cable through hole
at a time.
Installing Touchscreen
6
Outside
of Door
When touchscreen
is aligned properly
it will be flush
on door.
Inside
of Door

6
P/N YRM276/YRM476-INST-FUL Rev C
3. Install mounting bracket
with though bolts. Ensure
bracket is straight and
tighten bolts.
x2
Through Bolts
Inside of Door
Inside
of Door
Installing Inside Mounting Plate
7
1. Place spindle into lock.
2. Pull cables through
mounting bracket.
Spindle

7
P/N YRM276/YRM476-INST-FUL Rev C
8Installing Optional Door Position Sensor
Attach Door Position
Sensor assembly.
Back of Inside Lock shown
Door Position Sensor is on
latch side of door when
installed correctly.
Remove both tabs from
gasket if installing optional
Door Position Sensor.
Do not remove tabs if
optional Door Position
Sensor is not installed.
This step is optional and only needed when using Door Position Sensor.

8
P/N YRM276/YRM476-INST-FUL Rev C
9Attaching Cable Assemblies
Inside
of Door
Ensure cables are
securely fastened
into connector

9
P/N YRM276/YRM476-INST-FUL Rev C
10 Installing Inside Lock
Top of thumbturn must
face away from latch
x1
Decorative Screw
x2
#8x8 PHM
Store excess
cable in interior
lock cavity.
Tighten
Tighten

10
P/N YRM276/YRM476-INST-FUL Rev C
Inside
of Door
Testing Operation
Ensure thumbturn
moves freely