Assa Abloy Rixson Smok-Chek VI Quick guide

Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9372-0100-015 (02-14)
ASSA ABLOY
RIXSON®
1
Requirements:
Units are handed. Hand of unit and hand of door must be the same.
All dimensions shown in inches (mm).
Door must be hung on ball bearing butt hinges or 3/4" (19) offset pivots.
Door thickness must be 1-3/4" (44) to 2-1/4" (64).
Door must swing freely through the entire opening and closing cycle before beginning the installation procedure.
Frame face must be a minimum of 2" (51).
Ceiling clearance must be a minimum of 3 -1/2" (89) for push side application or 4" (102) for pull side application. See pages
2 and 7 for templates.
Power input to unit must be of the same voltage as that stated on the unit.
Unit to be mounted on interior of building in dry environment, maximum humidity of 95%.
See NFPA70 for wiring requirements and NFPA72 for alarm system requirements.
Pull Side Applications with Slide Track
(4 Pull, 6 Pull)
(see page 7 for template)
Push Side Applications with Double Lever Arms
(4 Push, 6 Push)
(see page 2 for template)
Item No. Description
1 Track (Pull Side)
2 Cover
3 Track Arm (Pull Side)
4 Double Lever Arm (Push Side)
• Allen wrench set (inch)
• Flat blade screwdriver (potentiometer &
terminal size)
• Screwdriver (Phillips size 2)
• Tape ruler
• Power drill
• Center punch
• Wire stripper
Tools required:
Use screw pack and hardware provided to mount operator.
312
4
Table of Contents:
Push Side Template....................2
Push Side Installation..............2-4
Closer Adjustments.....................5
Hold Open Position Adj...............6
Pull Side Template......................7
Pull Side Installation.................7-9
Closer Adjustments...................10
Hold Open Position Adj.............11
Non-Detectored Electrical.........12
Detectored Electrical.................13
RF Unit Electrical.................14-15
Troubleshooting.........................15
General Information..................16
ASSA ABLOY
RIXSON®Smok-Chek® VI
Installation and Instruction Manual
ASS
A ABL
O
Y
RIXSON®
ASSA ABL
OY
RIXSON®

Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9372-0100-015 (02-14)
ASSA ABLOY
RIXSON®
2
Double Lever Arm (Push Side)
Closer Mounting
2
Prepare Frame
Ceiling Line
2
(51)
3-1/2
(89)
Min
Min
Use of an auxiliary door stop, by
others, is required for these applications.
Hinge
Edge
Of
Door
DOOR OPENING
ANGLE
Dim “A”
Inches (mm)
To 100°
100° to 180°
5-7/8
3-1/8
149.2
79.4
Hinge or Pivot
Drill #7; Tap 1/4-20 UNC 19-3/4
1-3/4
(44.5)
C
4
(101.6)
11-1/4
(285.8)
(501.7)
For Concealed
Wiring Only
7/8
(22.2) DIA THRU
A
Left hand door shown, right hand opposite.
All dimensions shown in inches (mm).
Install two screws in
the key slot locations
leaving 1/8" gap
between screw head
and frame face as
shown (a).
C
1/8"
B
Dim “B”
Inches (mm)
13-3/8
10-5/8
339.7
269.9
1
Top of
Door
Frame
Soffit
1-3/4
(44.5)
7/8
(22.2)
Frame Rabbet
11/16
(17.5)
5/16
(7.9)
1-5/8
(41.3)
RH - Right Hand
LHR - Left Hand Reverse
LH - Left Hand
RHR - Right Hand Reverse
a

Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9372-0100-015 (02-14)
ASSA ABLOY
RIXSON®
3
Operator Mounting
3
c
Hang closer body
by key hole slots (b)
and slide closer
toward hinge to
capture screw
heads (c).
Warning: Do not
allow pedestrian
traffic through
opening until all
mounting screws
are tightened.
Closer Mounting
4
Install remaining
mounting screws
through back plate and
tighten all four screws
(d). Pull wiring through
holes (if concealed
wired).
Arm Shoe Mounting
5
Mount closer arm shoe to
door face as shown.
For Concealed Wired Only
(If surface wired, see page 13-15)
!
d
C
C
b
C

Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9372-0100-015 (02-14)
ASSA ABLOY
RIXSON®
4
Attach Arm
36
Preload Closer Spring
37
Arm Screw
(7/16” Drive)
Main
Arm F
Closer Spring Adjustment
38
11/16"
Wrench
+
Closing Force
Weaker
Stronger
Slowly increase closer power
until door closes consistently. A
closer set to the ADA required 5
lbs opening force may not be
strong enough to close the door
due to latching hardware, air
pressure, or frame issues.
F
L
R
Y
S
Z
Pinion
Flat
Arm
Mark
Align the pinion flat with
the letter "S".
!
90°
With the door closed and
latched, rotate main arm until
secondary arm is perpendicular
to the door frame, then tighten
adjustment screw as shown with
7/16” wrench.

Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9372-0100-015 (02-14)
ASSA ABLOY
RIXSON®
5
Closer Adjustments
39
+
-
1/8"
Hex
Key
"B"
Backcheck
75°
"L"
Latch
0°
5°
1/8"
Hex
Key
"P"
Backcheck
Position
75°
90°
"S"
Sweep
5°
!
Never Close
backcheck valve
completely
!
Do not remove valves
from closer. Hydraulic
oil will escape.
1/8"
Hex
Key
1/8"
Hex
Key
w
o
e
l
r
S
F
r
a
s
t
e
w
o
e
l
r
S
F
r
a
s
t
e
Weaker
Stronger
Closing Speed Controls
• Valve "S" Controls Sweep Range from
full open to 5°.
• Valve "L" Controls Latch Range from 5°
to closed.
Opening Cycle
• Valve "B" controls the strength of
cushioning in Backcheck Range.
NEVER close this valve completely – it
is not to provide a positive stop.
• Valve "P" adjusts the angle that back-
check is felt in the open cycle.
Electrical Connections
3
See Page 13 for Non-Detectored Units
See Page 14 for Detectored Units
See Page 15 for RF Units
10

Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9372-0100-015 (02-14)
ASSA ABLOY
RIXSON®
6
Attach Cover
312
Attach cover using screws provided.
Selective Hold Open Cam Adjustment
3
11
Setting Hold Open Angle
• Make all required electrical connections
and turn power switch to on for non-
detectored units (detectored units
cannot be turned off at the closer). (See
previous step)
• Open door to desired hold open angle.
• Loosen cam screw and rotate cam until
switch closes and door holds open.
• Rotate cam until it touches the switch.
• Tighten cam screw but do not over
torque as this will cause damage to
cam.
• Force door out of hold open by closing
the door, then test hold open by
opening to hold open angle again.
a
5/32” hex
wrench
b
c
5/32” hex
wrench
e
d
Right hand pull-side shown.
Switch shown in hold open position (closed).
Backplate
SHO switch in
open position.
Closer not in
hold open.
SHO switch in
closed position.
Closer in hold
open.
Un-used pin

Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9372-0100-015 (02-14)
ASSA ABLOY
RIXSON®
7
Track Mount (Pull Side)
Closer Mounting
2
Prepare Frame
Left Hand Door - LH
Right Hand Reverse - RHR
RH - Right Hand Door
LHR - Left Hand Reverse
Ceiling Line
2
(51)
4
(102)
Min
Min
Right hand door shown, left
hand opposite.
All dimensions shown in
inches (mm).
Install two screws in
the key slot locations
leaving 1/8" gap
between screw head
and frame as shown
(a).
a
C
1/8"
1
Track Mount Unit
6
(152.4)
19-1/8
(485.8)
CHinge or Pivot
3-1/4
(82.6)
3/4
(19)
For Concealed
Wiring Only
7/8
(22.2) DIA THRU
1-3/8
(34.9)
1-1/16
(27)
23
14-1/2
(368.3)
(584.2)
Prepare holes for mounting per instructions on page 2. *Track screws are
self tapping and are smaller than closer mounting screws*
1-1/4 (31.8)
Standard Arm
Double Egress Arm
Series Dim "A"
5/8 (15.9)
1/8 gap
(3.2)
Top of
Door
Frame
Soffit
A
(44.5)
1-3/4
7/8
(22.2)
*9/64 (3.6) Holes
for track screws*

Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9372-0100-015 (02-14)
ASSA ABLOY
RIXSON®
8
Closer Mounting
3
Closer Mounting
4
Arm Mounting
5
c
Install remaining
mounting screws
through back plate
and tighten all four
screws (d). Pull
wiring through holes
(if concealed wired). d
Fully close Latch & Sweep
Valves with 1/8" wrench
provided.
Mount closer arm to pinion square as shown.
Use main arm to rotate pinion
until flat is visible.
RE-INSTALL
HERE
LEFT
HAND
RIGHT
HAND
Attach with provided
screw and washer.
Tighten arm screw with
5/32" hex wrench.
Attach Arm
36
PINION
FLAT
LEFT
HAND
RIGHT
HAND
Align the pinion flat as
shown.
!
*All views from floor looking upward*
C
C
Hang closer body
by key hole slots (b)
and slide closer toward
hinge to capture screw
heads (c).
Warning: Do not allow
pedestrian traffic
through opening until
all mounting screws
are tightened.
*For Connected Free Swing Arm
see Instructions 80-9372-0101-000*
For Concealed Wired Only
(If surface wired, see page 13-15)
!
b

Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9372-0100-015 (02-14)
ASSA ABLOY
RIXSON®
9
A) Insert slider into track.
B) For openings 125°or less, insert spring
cushion stop on hinge side of track .
For openings greater than 125°, omit
spring stop.
C) Insert end caps (both ends).
D) Secure track to door using screws
provided.
E) Snap on cover.
Set Screws
toward hinge
!
If opening angle greater than 125°, spring cushion stop cannot be used and an auxiliary stop
by others is required.
Mount Track
37
Connect Arm to Track
38
Open door to maximum desired swing
minus 5° and hold. Slide spring
cushion stop assembly against slider
assembly and secure to track using
5/64" or 2mm wrench.
HINGE
Secure arm to slider
assembly using 3/16"
wrench. Turn wrench
counter clock wise to
tighten.
Open Latch & Sweep Valves
with 1/8" wrench provided.
A
B
C
D
E
Closer Spring Adjustment
39
11/16"
Wrench
+
Closing Force
Weaker
Stronger
Slowly increase closer power
until door closes consistently. A
closer set to the ADA required 5
lbs opening force may not be
strong enough to close the door
due to latching hardware, air
pressure, or frame issues.

Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9372-0100-015 (02-14)
ASSA ABLOY
RIXSON®
10
Closer Adjustments
3
10
+
-
1/8"
Hex
Key
"B"
Backcheck
75°
1/8"
Hex
Key
"P"
Backcheck
Position
75°
90°
"S"
Sweep
5°
!
Never Close
backcheck valve
completely
!
Do not remove valves
from closer. Hydraulic
oil will escape.
1/8"
Hex
Key
w
o
e
l
r
S
F
r
a
s
t
e
Weaker
Stronger
Closing Speed Controls
• Valve "S" Controls Sweep Range from
full open to 5°.
• Valve "L" Controls Latch Range from 5°
to closed.
Opening Cycle
• Valve "B" controls the strength of
cushioning in Backcheck Range.
NEVER close this valve completely – it
is not to provide a positive stop.
• Valve "P" adjusts the angle that back-
check is felt in the open cycle.
"L"
Latch
0°
5°
1/8"
Hex
Key
w
o
e
l
r
S
F
r
a
s
t
e
Electrical Connections
3
See Page 13 for Non-Detectored Units
See Page 14 for Detectored Units
See Page 15 for RF Units
11