Assa Abloy Norton 1600 UniTrol User manual

Non Hold Open (UL Listed)
Hold Open (H) (Not UL Listed)
Copyright © 2016, 2020, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9316-2533-020 Rev 2 02/20
1600 UniTrol®
Non Handed Door Closer
Standard Frame
Deep Reveal
Flush Transom
Sized
(Sizes 3,4)
UNI-1603BC (H)
UNI-1604BC (H)
Adjustable
(Sizes 1-6)
UNI-1601 (H)
Ce produit peut vous exposer au plomb qui, dans l’état de la Californie,
est reconnu pour causer le cancer, des anomalies congénitales ou d’autres
problèmes de reproduction. Pour plus d’informations, visitez:
www.P65warnings.ca.gov.
This product can expose you to lead which is known to the state of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65warnings.ca.gov.
WARNING
Tools Needed
TO DETERMINE
HAND OF
YOUR DOOR:
LEFT
HAND
DOOR
RIGHT
HAND
DOOR
Right Hand
Reverse
Left Hand
Reverse
To Determine Your Hand of Door: To Identify Your Model:
1-6 = 1601
3 = 1603BC
4 = 1604BC
Included Components (See page 2 for mounting hardware and optional components)
Standard Frame
(Reveals 1-7/8" to 4-5/8" - Uses 6190 Bracket)
Deep Reveal
(Reveals Over 4-5/8" - Uses 6191 Reinforcing Kit)
Flush Transom
(Uses 2022 Bracket)
Right Hand Door - RH
Left Hand Reverse - LHR
Left Hand Door - LH
Right Hand Reverse - RHR
Right Hand Door - RH
Left Hand Reverse - LHR
Left Hand Door - LH
Right Hand Reverse - RHR
Right Hand Door - RH
Left Hand Reverse - LHR
Left Hand Door - LH
Right Hand Reverse - RHR
Arm Identication (Stamped on Arm)
Door Width Main Arm Non Hold
Open
Hold
Open
28" - 32"
(0.70 - 0.80m)
9-1/2"
(241mm) 6100-11 6100-1
33" - 41"
(0.85 - 1.00m)
11"
(279mm) 6100-13 6100-3
42" - 48"
(1.05 - 1.20m)
12-1/2"
(318mm) 6100-14 6100-4

Copyright © 2016, 2020, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9316-2533-020 Rev 2 02/20
2
• For special applications, a separate door and frame
preparation template is packed with these instructions. Use
this instruction sheet for installation sequence and closer
adjustments only.
• Doors should be hung on ball bearing or anti-friction hinges.
• Door and frame must be properly reinforced.
Mounting Hardware Door or Frame Drill
Closer, Soft Plate:
1/4-14 x 1-1/2 Oval Flat Head Mach. Screw Wood 3/16" (4.76mm)
Closer, Soft Plate:
1/4-20 x 3/4 Oval Flat Head Mach. Screw Metal Drill #7 (.201 dia. or 5.10mm) Tap 1/4-20
Closer:
Sleeve Nut and Bolt (SNB)
(optional)
Hollow Metal 9/32" (7.00mm) thru
3/8" (9.50mm) door face opposite to closer
Aluminum or Wood 3/8" (9.50mm) thru
Closer:
Thru Bolt and Grommet Nut (TBGN)
(optional)
All
9/32" (7.00mm) thru
3/8" (9.50mm) dia. x 3/8" (9.500mm) deep,
door face opposite to closer
• Always consult door/frame manufacturer for fastener
compatibility.
• Adjust closing time speed between 4 and 7 seconds from
90° to 0°. Use of door by handicapped, elderly or small
children may require greater closing time.
• These door closers should NOT be installed on exposed side
(weather side) of exterior doors.
• Dimensions are given in inches (millimeters).
ATTENTION:
An incorrectly installed or improperly adjusted door closer can
cause property damage or personal injury. These installation
instructions should be followed to avoid the possibility of
misapplication or misadjustment.
1600 UniTrol Arm Closer
Brackets
Door Holder
Reinforcing Kit
2022
Option for Flush Transom
6190
Option for Standard Frame
1688C Drop Plate
For use with optional cover
1688 Drop Plate
For narrow top rail
Drop Plates
Cover
6191
Option for Deep Reveal
1600P

Copyright © 2016, 2020, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9316-2533-020 Rev 2 02/20 3
28" - 32" Wide Doors
Opening A B C
Hold Open Stop
85° 90° 10-1/2"
(267)
8-5/8"
(219)
9-5/8"
(244)
90° 95° 9-3/4"
(248)
8"
(203)
9"
(229)
95° 100° 9-1/4"
(235)
7-1/2"
(191)
8-1/2"
(216)
100° 105° 8-7/8"
(225)
7-1/8"
(181)
8-1/8"
(206)
105° 110° 8-1/2"
(216)
6-3/4"
(171)
7-3/4"
(197)
110° 115° 8-1/8"
(206)
6-3/8"
(162)
7-3/8"
(187)
23" - 41" Wide Doors
Opening A B C
Hold Open Stop
85° 90° 12-5/8"
(321)
11"
(279)
12"
(305)
90° 95° 12"
(305)
10-3/8"
(264)
11-3/8"
(289)
95° 100° 11-3/8"
(289)
9-3/4"
(248)
10-3/4"
(273)
100° 105° 10-7/8"
(276)
9-1/4"
(235)
10-1/4"
(260)
105° 110° 10-3/8"
(264)
8-3/4"
(222)
9-3/4"
(248)
110° 115° 10"
(254)
8-3/8"
(213)
9-3/8"
(238)
42" - 48" Wide Doors
Opening A B C
Hold Open Stop
85° 90° 15"
(381)
13-1/4"
(337)
14-1/4"
(362)
90° 95° 14-1/4"
(362)
12-1/2"
(318)
13-1/2"
(343)
95° 100° 13-5/8"
(346)
11-7/8"
(302)
12-7/8"
(327)
100° 105° 13"
(330)
11-1/4"
(286)
12-1/4"
(311)
105° 110° 12-1/2"
(318)
10-3/4"
(273)
11-3/4"
(298)
110° 115° 12"
(305)
10-1/4"
(260)
11-1/4"
(286)
1600 UniTrol Arm - Templates (Right Hand Shown)
Notes:
1. IMPORTANT: Door template is typical for all
installations. Frame template must be selected
according to frame reveal.
2. If top rail is as narrow as 2-5/8" (67mm) and
prevents closer from being mounted directly to
door surface, use 1688 Drop Plate. Prepare door
and frame accordingly.
1-7/8" - 4-5/8" Standard Frame Reveal (With Door Template)
Hinge
or
Pivot
C
L
3/4
(19.1)
1-3/4
(44)
2022 Bracket
(See Page 2)
1/2
(12.7)
2-1/2
(63.5)
1-1/2
(38.1)
C+ 1/8 (3.2)
Over 4-5/8" Deep Frame Reveal Template
Flush Transom Template

Copyright © 2016, 2020, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9316-2533-020 Rev 2 02/20
4
1600 UniTrol Arm Installation (Right Hand Shown)
2. Close latch and
sweep valves.
3. Install arm to frame.
S
L
5. Rotate closer pinion to align at as shown.
S and L valves
AWAY from hinge
1. Prepare door and frame.
1. Be sure that arm is correct for door width.
See “Components” on page 1.
2. Be sure that correct frame and door template
combination is used to prepare for installation.
See “Templates” on page 3.
3. Using dimensions for hold-open or door stop
angle desired, mark and drill
• Four (4) holes on door for closer (or drop
plate)
• Six (6) holes on frame for soft plate and 6190
bracket (See Figure 1) or
• Four (4) holes on frame for soft plate and
6191 reinforcing kit (See Figure 2) or
• Four (4) holes on frame for 2022 angle bracket
(See Figure 3)
4. UNI1601 ONLY: Set approximate closing power
using “Spring Power Adjustment” chart on page 5.
To ease optional cover
installation, insert cover
screws onto closer
(leaving a slight gap)
before mounting closer.
Figure 1. 1-7/8" - 4-5/8" Standard Frame With 6190 Bracket
Figure 2. Over 4-5/8" Deep Reveal With 6191 Reinforcing Kit
Figure 3. Flush Transom With 2022 Bracket
4. Mount drop plate (if used) and closer.
Standard Frame - 6190 Bracket Deep Reveal - 6191 Kit Flush Transom - 2022 Bracket

Copyright © 2016, 2020, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9316-2533-020 Rev 2 02/20 5
1600 UniTrol Arm Installation (Right Hand Shown)
6. Attach arm to closer. 7. Open latch and sweep valves.
S
L
Do not completely
open valves. Valves
will leak.
You’ve now installed the 1600 UniTrol Arm Closer.
🛑 Continue with closer adjustments and decorative cap or cover installation.
RH: Position at at R
LH: Position at at L
Closer Adjustments
Latch Backcheck
Use provided 1/8" hex wrench to
turn valves.
NEVER force valves out of closer.
NEVER completely close
backcheck valve. Backcheck
is not a positive stop.
Door must be open to adjust
spring closing power. Refer to
chart.
Do not use a power drill.
Warranty will be void. Sweep
Do not over tighten
cap or cover screws
Pinion Cap or Cover
Screw pinion cap onto pinion
shaft by hand or with a Phillips
screwdriver.
OR
Slide cover over closer and secure
mounting screws after installation
is complete.

Norton is a brand associated with ASSA ABLOY Accessories and Door Controls Group, Inc., an ASSA ABLOY Group company.
Copyright © 2016, 2020, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited. 80-9316-2533-020 Rev 2 02/20
Norton Technical Product Support:
Monroe, NC 28112 USA
Phone: [phone] ext: 6030
[e-mail]
nortondoorcontrols.com