Avtech AVH364 User manual

h364_336_manual_V1.0
36CH / 64CH HD NVR
SERIES
Operation Guide
Please read instructions thoroughly before operation and retain it for future reference.
Online manual download: www.surveillance-download.com/user/h364.swf

IMPORTANT SAFEGUARD
All lead-free products offered by the company comply with the requirements of the
European law on the Restriction of Hazardous Substances (RoHS) directive, which means
our manufacture processes and products are strictly “lead-free” and without the hazardous
substances cited in the directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product
must be collected separately at the product end-of-life. This applies to your product and
any peripherals marked with this symbol. Do not dispose of these products as unsorted
municipal waste. Contact your local dealer for procedures for recycling this equipment.
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at
his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device mat not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Disclaimer
iPad and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a
service mark of Apple Inc.
IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.
Google Play and Android are trademarks of Google Inc
We reserve the right to revise or remove any content in this manual at any time. We do not warrant or assume
any legal liability or responsibility for the accuracy, completeness, or usefulness of this manual. The content of
this manual is subject to change without notice.
This product doesn’t have a standby / off mode.

MPEG4 Licensing
THIS PRODUCT IS LICENSED UNDER THE MPEG4 VISUAL PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING VIDEO IN
COMPLIANCE WITH THE MPEG4 VISUAL STANDARD (“MPEG-4 VIDEO”) AND/OR (ii) DECODING
MPEG4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND
NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY
MPEG LA TO PROVIDE MPEG4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY
OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL INTERNAL
AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE
HTTP://WWW.MPEGLA.COM.
GPL Licensing
This product contains codes which are developed by Third-Party-Companies and which
are subject to the GNU General Public License (“GPL”) or the GNU Lesser Public License
(“LGPL”).
The GPL Code used in this product is released without warranty and is subject to the
copyright of the corresponding author.
Further source codes which are subject to the GPL-licenses are available upon request.
We are pleased to provide our modifications to the Linux Kernel, as well as a few new
commands, and some tools to get you into the code. The codes are provided on the FTP
site, and please download them from the following site or you can refer to your distributor:
http://download.dvrtw.com.tw/GPL/NVR/T-Series/linux.tar.gz

TABLE OF CONTENTS
1. HARDWARE OVERVIEW ................................................................................................................... 1
1.1 Front Panel................................................................................................................................................ 1
1.2 Rear Panel ................................................................................................................................................ 1
2. CONNECTION.................................................................................................................................... 2
2.1 Hard Disk Installation ................................................................................................................................ 2
2.1 Connection ................................................................................................................................................ 4
3. FOR INITIAL USE ............................................................................................................................... 5
3.1 Setup Wizard............................................................................................................................................. 5
3.2 Clear Hard Disk ......................................................................................................................................... 7
3.3 Change User Name and Password........................................................................................................... 8
4. CAMERA SETUP................................................................................................................................ 9
4.1 Camera IP Configurations by LAN ............................................................................................................ 9
4.2 Manual Connection Setup....................................................................................................................... 10
5. USER INTERFACE............................................................................................................................11
5.1 Local Access ........................................................................................................................................... 11
5.2 Local........................................................................................................................................................ 11
5.2.1 Device Status .................................................................................................................................................11
5.2.2 Channel Status ...............................................................................................................................................12
5.2.3 Quick Operation .............................................................................................................................................12
5.2.4 Main Menu......................................................................................................................................................12
5.2.5 Playback Panel...............................................................................................................................................13
6. FREQUENTLY-USED FUNCTIONS ................................................................................................. 14
6.1 Key Lock / Unlock.................................................................................................................................... 14
6.2 IP Device Search..................................................................................................................................... 14
6.3 User Level Creation................................................................................................................................. 15
6.4 PTZ Control............................................................................................................................................. 17
6.5 Event Search........................................................................................................................................... 19
6.6 Video Backup .......................................................................................................................................... 20
6.7 Video Playback on PC............................................................................................................................. 21
6.7.1 Convert the file format to AVI .........................................................................................................................21
7. MAIN MENU ..................................................................................................................................... 22
7.1 QUICK START ........................................................................................................................................ 22
7.1.1 GENERAL ......................................................................................................................................................22
7.1.2 TIME SETUP..................................................................................................................................................24
7.1.3 SIMULATION..................................................................................................................................................25
7.2 SYSTEM.................................................................................................................................................. 26
7.2.1 ACCOUNT......................................................................................................................................................26
7.2.2 TOOLS ...........................................................................................................................................................26
7.2.3 SYSTEM INFO ...............................................................................................................................................27
7.2.4 BACKUP SCHEDULE ....................................................................................................................................28
5.2.5 ONLINE ..........................................................................................................................................................29
7.3 EVENT INFORMATION .......................................................................................................................... 29
7.3.1 QUICK SEARCH............................................................................................................................................29
7.3.2 EVENT SEARCH ...........................................................................................................................................30
7.3.3 HDD INFO ......................................................................................................................................................30
7.3.4 EVENT LOG...................................................................................................................................................30

7.4 ADVANCED CONFIG.............................................................................................................................. 31
7.4.1 CONNECTION ...............................................................................................................................................31
7.4.2 CAMERA ........................................................................................................................................................32
7.4.3 DETECTION...................................................................................................................................................33
7.4.4 ALERT ............................................................................................................................................................35
7.4.5 NETWORK .....................................................................................................................................................36
7.4.6 DISPLAY ........................................................................................................................................................39
7.4.7 RECORD........................................................................................................................................................40
7.4.8 NOTIFY ..........................................................................................................................................................41
7.4.9 MULTICASTING.............................................................................................................................................45
7.4.10 JOYSTICK....................................................................................................................................................46
7.5 SCHEDULE SETTING ............................................................................................................................ 47
7.5.1 RECORD / EVENT / BUZZER .......................................................................................................................47
7.5.2 REGULAR REPORT......................................................................................................................................47
7.5.3 REGULAR REBOOT......................................................................................................................................48
8. REMOTE OPERATION..................................................................................................................... 49
8.1 Web Browser........................................................................................................................................... 49
8.2 Mobile Devices........................................................................................................................................ 50
8.3.1 Prerequisites ..................................................................................................................................................50
8.3.2 Where to download ........................................................................................................................................50
8.3.3 Setup ..............................................................................................................................................................50
APPENDIX 1 COMPATIBLE USB FLASH DRIVE LIST ........................................................................ 52
APPENDIX 2 COMPATIBLE HARD DISK LIST .................................................................................... 53
APPENDIX 3 BATTERY REPLACEMENT............................................................................................ 54
APPENDIX 4 SPECIFICATIONS .......................................................................................................... 55
APPENDIX 5 MENU TREE................................................................................................................... 57
APPENDIX 6 EAZY NETWORKING..................................................................................................... 59
A6.1 Via EagleEyes on iOS / Android Device .........................................................................................................59
A6.2 Via Internet Explorer on PC / Laptop ..............................................................................................................64
A8.3 Cloud Icons .....................................................................................................................................................69
APPENDIX 7 PUSH VIDEO CONFIGURATION ................................................................................... 70
A7.1 Alarm Sensor Connection ..................................................................................................................... 70
A7.2 Configuration......................................................................................................................................... 70

HARDWARE OVERVIEW
1
1. HARDWARE OVERVIEW
This NVR has divided all channels into four groups for live display and recording, and videos in each group are
recorded to specific hard disks as indicated below. The first two groups have three hard disks to record, and the last
two groups have two hard disks to record.
If such storage allocation is not sufficient, AVX993, the disk array, could be used to connect to this NVR to expand the
storage of each group to five hard disks, as indicated below.
1.1 Front Panel
1) LED indicators
Internet The device is connected to Internet.
LAN The device is connected to LAN.
Alarm An alarm event occurs.
Mini SAS An external disk array is connected.
Error Any of the adapter, power and fan is abnormal.
2) Power ( )
Press to power on the device; press and hold for 3 seconds to power off the device.
3) Mouse port ( )
Insert a mouse for function operation.
4) USB port ( )
Insert a compatible USB flash drive for video backup.
Note: For the compatible list of USB flash drives, please refer to “APPENDIX 1 COMPATIBLE USB FLASH
DRIVE LIST” at page 52.

HARDWARE OVERVIEW
1
5) HDD Indicators
Check the HDD indicator for each installed hard disk to ensure the hard disks work normally.
Color Status Meaning
-- No light No hard disk is installed, or the installed hard disk is not detected. Please install a hard disk
or replace the installed hard disk, and try again.
Green Always on The installed hard disk is detected well.
Green Flashing Data reading / writing.
Red Always on The installed hard disk is failed. Please replace the installed hard disk, and try again.
Red Flashing Data building or recovering.
1.2 Rear Panel
1) HDMI
This port is used to connect the monitor, which supports HDMI interface.
Note: Direct connection to the monitor, which supports VGA or composite interface, is not supported.
Please prepare a converter in advance.
2) INTERNET
This port is used to connect your device to Internet.
3) LAN
This port is used to connect IP cameras to this device with a hub (if necessary) locally.
4) MINI SAS
This port is used to connect to the disk array which supports MINI SAS port, such as AVX993.
5) EXTERNAL I/O
Insert the supplied external I/O block, and users are able to connect external devices.
6) DC19.5V Jack
Connect the device to power with the regulated adapters. For initial use, the device will be powered on
immediately when the adapter is connected.
7) LED indicators for adapters, fans, and power modules
There are indicators for FAN, ADAPTER, and power modules (3.3V / 5V / 12V) for users to diagnosis the
status of fans, adapters and power modules.
When any of the indicators is red, the ERROR indicator on the front panel will turn red to warm the users,
and you’ll see “ ” on the live view.
Color Meaning
Green OK
Red 1. No use.
2. Something's wrong with any of the fans, adapters, or power
modules. Please check with your installer or distributor for repair if
necessary.

CONNECTION
2
2. CONNECTION
2.1 Hard Disk Installation
Note: It’s necessary to install a hard disk first before firmware upgrade to ensure the upgrade process
works properly.
Step1: Remove the cover by loosening the left side of the cover’s screws.
HDD2HDD3HDD4HDD5HDD6HDD7HDD8HDD9HDD10
HDD
12345678910
HDD2HDD3HDD4HDD5HDD6HDD7HDD8HDD9HDD10
Step2: Find the hard disk connector and HDD tray in the device. Press the button of the HDD tray as indicated
below and remove it.
HDD Tray: Press to remove
Step3: Get a compatible hard disk. With the PCB side facing the internal of the HDD tray and the hard disk‘s
connector facing the outside.
Then, find the HDD screws supplied in the sales package. Align the hard disk’s screw holes with the HDD
tray’s holes and fasten the screws.
HDD

CONNECTION
3
Step4: Place the HDD tray to the device, and push it to the end till you feel the hard disk is inserted to the hard disk
connector.
Then, lock the HDD tray as shown below.
You’ll see 4 different colors of labels on the drive bays. They’re corresponding to the drive bays of AVX993
(the disk array), and each color will have five drive bays in total when AVX993 is connected to this NVR.
GROUP HDD COLOR
LABEL
HDD NUMBERING
NVR AVX993
1 Blue 1 ~ 3 9 ~ 10
2 Orange 4 ~ 6 7 ~ 8
3 Pink 7 ~ 8 4 ~ 6
4 Green 9 ~ 10 1 ~ 3
Step6: Replace the front cover and fasten the screws you loosened in Step1.
HDD2HDD3HDD4HDD5HDD6H
DD7HDD8HDD9

CONNECTION
4
2.1 Connection
Connect a monitor, IP cameras, adapters, a mouse, and other devices necessary to this recorder as illustrated below.
Then, power on the whole system and wait till the system initialization is done.
Note: When AVX993, the disk array, is connected to this NVR, please power on AVX993 first. Otherwise,
the NVR might not detect AVX993 properly.
Wait till the HDD indicators turn green. For details, please refer to “1.1 Front Panel” at page 1.

FOR INITIAL USE
5
3. FOR INITIAL USE
This NVR has divided all 64 channels into four groups for live display and recording. To control this NVR, you need to
first access the group within which includes the control you want to make.
To switch to one of the group:
For the first time to power on this device, you might be prompted to:
Go through the setup wizard
Clear hard disk
Change default user name and password
3.1 Setup Wizard
The setup wizard is prompted to guide you finishing the most common settings you might need to do.
Note: It’s okay to skip the wizard. You can configure the following settings later in their respective
menus.
SETUP WIZARD
ENGLISH
WELCOME TO THE SETUP WIZARD.
PLEASE FOLLOW THE WIZARD TO FINISH BASIC CONFIGURATIONS.
SKIP EaZy NEXT
Choose “EaZy” (EaZy Networking) to directly go to the EaZy Networking setting page, and refer to “APPENDIX 6
EAZY NETWORKING” at page 59 for details.
Note: To configure network setup by using EaZy Networking later, please go to QUICK START EaZy.
Or select “NEXT” to go to the next step.
SETUP WIZARD
PLEASE INPUT THIS MACHINE NAME
SKIP PREV NEXT

FOR INITIAL USE
6
Name the device. If you don’t want to name the device, just skip to the next step.
Note: To name the device later, please go to SYSTEM SYSTEM INFO.
SETUP WIZARD
USER NAME office_hd
PASSWORD office145
CONFIRM PASSWORD office145
PLEASE INPUT THE ADMINISTRATOR’S USER NAME AND PASSWORD.
SKIP PREV NEXT
Change the default user name and password. If you don’t change the user name and password here, you’re not able to
go to the next step. This step is compulsory.
Note: To change or edit user name and passwords, please go to SYSTEM ACCOUNT.
SETUP WIZARD
DATE 2015/MAR/05
TIME 14:33:46
FORMAT Y/M/D
GMT GMT+08:00
SKIP PREV NEXT
Set the date and time.
If you don’t want to set the date and time now, just skip to the next step. However, it’s necessary to keep the date and
time right to ensure the accuracy of the recorded data.
Note: To set the date and time later, please go to QUICK START TIME SETUP. When the date and
time are changed, you’ll be prompted to clear the hard disk(s). Select “YES” to erase the previous
recorded data, or there might be data disorder and you wouldn’t find the footage you need.
SETUP WIZARD
NTP SERVER Pool.ntp.org
SYNC PERIOD OFF
SKIP PREV NEXT
Configure if you want to connect this device to an NTP server to get the right time online.
Note: To set the date and time later, please go to QUICK START TIME SETUP.
SETUP WIZARD
NETWORK TYPE STATIC
IP 192.168.1.10
GATEWAY 192.168.1.1
NETMASK 255.255.255.0
PRIMARY DNS 8.8.8.8
SECONDARY DNS 168.95.1.1
PORT 80
SKIP PREV NEXT

FOR INITIAL USE
7
Configure network setup by using the traditional method. For details, please download
www.surveillance-download.com/user/network_setup/network_setup_recorder.pdf.
Note: To configure network setup by using the traditional method later, please go to ADVANCED
CONFIG NETWORK.
SETUP WIZARD
SMTP SERVER Smtp.gmail.com
PORT 465
MAIL FROM [e-mail]
SSL ENCRYPTION ON
VERIFY PASSWORD ON
USER NAME [e-mail]
PASSWORD ●●●●●●
SKIP PREV NEXT
Configure event notifications by email.
Note: To configure email notifications later, please go to ADVANCED CONFIG NETWORK -> EMAIL.
SETUP WIZARD
DDNS ON
SYSTEM NAME Eagleeyes
HOST NAME MAC000E533A3D
E-MAIL
CURRENT HOST ADDRESS
MAC000E533A3D4A.ddns.eagleeyes.tw
SKIP PREV NEXT
Enable DDNS if needed. For details, please download
www.surveillance-download.com/user/network_setup/network_setup_recorder.pdf.
Note: To enable the DDNS later, please go to ADVANCED CONFIG NETWORK DDNS.
3.2 Clear Hard Disk
When this device is powered on, hard disk detection will be on, and you’ll be prompted to clear the hard disk(s):
CLEAR HDD
CLEAR HDD HDD0
YES NO
Please choose YES to clear the connected hard disk(s), or this device will not detect hard disks properly for video
recording.
It might take some time to clear the connected hard disk(s). When it’s done, you’ll see the remaining hard disk capacity
on the top right corner of the screen.
Note: It’s necessary to clear hard disks in order to format the connected disks to the right format to save
video data. The format used for this device can NOT be read directly on a PC. Please do not install
the hard disk directly to a PC and try to copy the video data saved in the hard disk. The video data
might be impaired.

FOR INITIAL USE
8
To change later, right click to show the main menu, and select (SYSTEM) SYSTEM INFO CLEAR HDD.
The NVR will reboot when hard disk data are cleared.
SYSTEM
ACCOUN
T
AUTO KEY LOCK(S) NEVER
T
OOLS CLEAR HDD HDD-0
SYSTEM INFO RESET DEFAULT SUBMIT
BACKUP SCHEDULE REMOTE CONTROL ID 000
ONLINE DEVICE TITLE OFFICE
MCU VERSION 1001
VERSION 1016-1007-1011-1003
EXIT
3.3 Change User Name and Password
It’s highly recommended to change the user name and password of this device to keep your account safe. Otherwise,
any person could access this device if he knows the default user name and password.
If you didn’t go through the setting wizard at the first place, you’ll be prompted to change the user name and password:
WARNING
PLEASE BE ADVISED TO MODIFY THE DEFAULT
ACCOUNT TO ENSURE YOUR INFORMATION
SECUIRTY.
MODIFY
OREMIND ME LATER
ODON’T REMIND ME ANYMORE
CONFIRM
Choose MODIFY to start the change immediately.
To change later, right click to show the main menu, and select (SYSTEM) ACCOUNT to change the default
user name and password of SUPERVISOR.
SYSTEM
ACCOUNT USER LIST
TOOLS USER NAME LEVEL
SYSTEM INFO admin SUPERVISOR
BACKUP SCHEDULE
ONLINE
EXI
T
ADD EDIT DEL

CAMERA SETUP
9
4. CAMERA SETUP
4.1 Camera IP Configurations by LAN
Auto mode is to simplify the complicated network settings within three minutes. The connection mode of the LAN
port is AUTO by default. This mode is suitable when the LAN port of the device is connected to a hub.
Note: SETTING Path: (ADVANCED CONFIG) NETWORK LAN MODE.
Note: For access this recorder remotely with your mobile device or laptop, you need to connect this
recorder to Internet. For details, please get the setup manual from the supplied CD or from
www.surveillance-download.com/user/network_setup/network_setup_recorder.pdf.
The device will automatically configure the IP address of a camera connected by LAN if:
The connected IP camera is our brand’s IP camera.
Reset the IP camera to default value (the default IP configuration method of the camera is DHCP).
The camera is powered on before the device is powered on.
If the device doesn’t configure the IP address of your camera automatically as described above, your IP
camera might NOT be:
Our brand’s IP camera.
Set to DHCP as its default IP configuration method.
To solve this, use our brand’s IP camera, and reconfigure its IP address to 10.1.1.xx (xx ranges from 11 ~
253), in the same network segment as the device.
a) Move your mouse to the left side of the screen to show the quick bar, and select “ ”. You’ll see the list of
every connected IP camera with its connection status to this device and MAC address.
b) Select the IP address which is not used, and select SETUP.
IP SEARCH
IP PORT MAC TYPE PROTOCOL STATUS
10.1.1.12 88 00:0e:53:e5:9a:f1 IP CAMERA AVTECH CONNECTED TO CH1
10.1.1.12 88 UNKNOWN IP CAMERA ONVIF CONNECTED TO CH1
10.1.1.13 88 00:0e:53:a6:91:18 IP CAMERA AVTECH CONNECTED TO CH2
10.1.1.13 88 UNKNOWN IP CAMERA ONVIF CONNECTED TO CH2
10.1.2.14 88 00:0e:53:a5:9f:a2 SWITCH AVTECH UNUSED
10.1.2.14 88 00:0e:53:a5:9f:a2 SWITCH AVTECH UNUSED
10.1.1.15 88 00:0e:53:e1:4e:k5 IP CAMERA AVTECH CONNECTED TO CH3
10.1.1.15 88 UNKNOWN IP CAMERA ONVIF CONNECTED TO CH3
10.1.1.16 88 00:0e:53:s5:3e:h6 IP CAMERA AVTECH CONNECTED TO CH4
10.1.1.16 88 UNKNOWN IP CAMERA ONVIF CONNECTED TO CH4
10.1.1.17 88 00:0e:53:e6:4b:26 IP CAMERA AVTECH CONNECTED TO CH5
10.1.1.17 88 UNKNOWN IP CAMERA ONVIF CONNECTED TO CH5
 CONNECT SETUP EXIT
c) Select DHCP in NETWORK TYPE.

USER INTERFACE
10
d) Click APPLY and EXIT to save your changes.
SETUP
NETWORK TYPE DHCP
IP 10.1.1.14
PORT 88
USER NAME admin
PASSWORD *****
NETMASK 255.0.0.0
GATEWAY 10.1.1.10
PRIMARY DNS 168.95.1.1
APPLY EXIT
e) The device will then detect the IP camera and display images soon.
4.2 Manual Connection Setup
Note: SETTING Path: (ADVANCED CONFIG) CONNECTION.
To manually assign the address of your camera connected locally, click URI to modify.
ADVANCED CONFIG
CONNECTION CHANNE
L
UR
I
CONFIG
CAMERA CH1 AVTECH://ip_office.ddns.eagleeyes.tw:80 SETUP
DETECTION CH2 ONVIF://10.1.1.14:88 SETUP
ALER
T
CH3 AVTECH://10.1.1.30:88 SETUP
NETWORK CH4 AVTECH://10.1.1.12:88 SETUP
DISPLA
Y
RECORD
NOTIF
Y
MULTICASTING
JOYSTICK
EXI
T
Note: To configure this recorder to access other IP camera connected remotely for live viewing or video
backup, you need to connect this recorder to Internet first. For details, please get the setup
manual from the supplied CD or from
www.surveillance-download.com/user/network_setup/network_setup_recorder.pdf.

USER INTERFACE
11
5. USER INTERFACE
This NVR has divided all 64 channels into four groups for live display and recording. To control this NVR, you need to
first access the group within which includes the control you want to make.
To switch to one of the group:
5.1 Local Access
Connect your USB mouse to one of the USB ports on the front panel, and check if there’s a mouse icon ( ) on the
screen, indicating the USB mouse is detected properly.
Move your mouse to enter the password with the password keypad. The default user name and password are both
“admin”. The status will be changed from (key lock) to (unlock).
Note: You may configure four different user levels to have different access privileges in SYSTEM ACCOUNT.
For details, please refer to “6.3 User Level Creation” at page 15.
Password Input
5.2 Local
5.2.1 Device Status
Note: The functions shown may vary based on the model or the access user level you use.
Key lock Key unlock
Channel lock Channel unlock
USB flash drive / device connected No USB device connected
Timer record on Timer record off
Overwrite on Overwrite off
Sequence mode on Sequence mode off
PTZ mode on PTZ mode off
Backup event queued and USB flash drive needed USB flash drive full
CPU loading Error on fans, adapters or power module
Network Status:
(WAN) Internet connected (WAN) Internet disconnected
(WAN) Local connection
(LAN) Auto mode –Mbit/s (LAN) Auto mode – Gbit/s
(LAN) DHCP / Static IP mode (LAN) Camera disconnected

FREQUENTLY-USED FUNCTIONS
12
5.2.2 Channel Status
Note: The functions shown may vary based on the model or the access user level you use.
Auto search on Auto search off Original size Fit to screen
Live audio on Audio off Audio playback on Audio playback off
Recording PTZ control Alarm event Motion event
Live information Playback information Digital zoom Channel Playback
Quick camera control
5.2.3 Quick Operation
Move to the arrow mark to extend the quick menu bar and show the four functions as follows:
Note: When the 6CH display layout is changed to 3x2, the menu icons and layout will also be changed.
For details, please refer to “7.4.6 DISPLAY” at page 38.
6CH Display Layout Description
1x5 (default) 3x2
Click to show the channel switch panel and select the channel mode you want.
The 6CH display layout could be changed in ADVANCED CONFIG DISPLAY DISPLAY
LAYOUT FOR SIX CHANNELS. For details, please refer to “7.4.6 DISPLAY” at page 39.
-- Click to display the playback control panel, and click to play the latest recorded video clip, or click
to enter the search list.
Click to open the IP search window and check the current connection status of each channel.
Click to show the power off panel to either halt or reboot the system.
5.2.4 Main Menu
Right-click anywhere on the screen to show the main menu as follows, and right-click again to exit.
6CH Display Layout Description
1x5 (default) 3x2
QUICK START Click to set the status display, image settings, and date & time.
SYSTEM Click to set the system configurations.
EVENT
INFORMATION Click to enter the event search menu.
ADVANCED
CONFIG
Click to set CONNECTION, CAMERA, DETECTION, ALERT, NETWORK,
DISPLAY, RECORD, NOTIFY, MULTICASTING and JOYSTICK.
SCHEDULE
SETTING
Click to set timer for record, motion detection, Push Video, buzzer, auto backup,
and regular reboot.

FREQUENTLY-USED FUNCTIONS
13
5.2.5 Playback Panel
Fast Forward Increase the speed for fast forward.
Fast Rewind Increase the speed for fast rewind.
/
Play / Pause Click to play the latest recorded video clip immediately, and click again to pause.
In the pause mode, click once to get one frame forward, and click to get one frame rewind.
Stop Click to stop the video playback.
Slow Playback Click once to get 1/4X speed playback, and click twice to get 1/8X speed playback.
/ Previous /
Next Hour
Click to jump to the next / previous time interval in an hour, for example, 11:00 ~ 12:00 or
14:00 ~ 15:00, and start playing the earliest event video clip recorded during this whole hour.
Quick Search Click to enter the quick search menu for specific record data search.
Repeat Click to set point A and point B in a video clip, and the system will play only the specified range in
that clip.
Backup Click to open the backup menu for video backup.

REMOTE OPERATION
14
6. FREQUENTLY-USED FUNCTIONS
6.1 Key Lock / Unlock
To lock or unlock local operation, click (unlock) or (lock) on the device status bar to change the status
to (lock) or (unlock).
To unlock local operation, you’ll be prompted to enter the user name and password to access.
Note: The default user name and password are both “admin”, which is the highest user level
Note: Different user level has different access privilege for certain functions. For details, please refer to
“6.3 User Level Creation” at page 15.
6.2 IP Device Search
Note: This function is available only for “SUPERVISOR”. To know more details, please refer to “6.3 User
Level Creation” at page 15.
Click (IP Search) to start searching IP camera(s) connected in the same network segment as the recorder
(i.e. 10.1.1.xx by default).
You’ll see the list of every connected IP camera with its connection status to this recorder and MAC address.
IP SEARCH
IP PORT MAC TYPE PROTOCOL STATUS
10.1.1.12 88 00:0e:53:e5:9a:f1 IP CAMERA AVTECH CONNECTED TO CH1
10.1.1.12 88 UNKNOWN IP CAMERA ONVIF CONNECTED TO CH1
10.1.1.13 88 00:0e:53:a6:91:18 IP CAMERA AVTECH CONNECTED TO CH2
10.1.1.13 88 UNKNOWN IP CAMERA ONVIF CONNECTED TO CH2
10.1.2.14 88 00:0e:53:a5:9f:a2 SWITCH AVTECH UNUSED
10.1.2.14 88 00:0e:53:a5:9f:a2 SWITCH AVTECH UNUSED
10.1.1.15 88 00:0e:53:e1:4e:k5 IP CAMERA AVTECH CONNECTED TO CH3
10.1.1.15 88 UNKNOWN IP CAMERA ONVIF CONNECTED TO CH3
10.1.1.16 88 00:0e:53:s5:3e:h6 IP CAMERA AVTECH CONNECTED TO CH4
10.1.1.16 88 UNKNOWN IP CAMERA ONVIF CONNECTED TO CH4
10.1.1.17 88 00:0e:53:e6:4b:26 IP CAMERA AVTECH CONNECTED TO CH5
10.1.1.17 88 UNKNOWN IP CAMERA ONVIF CONNECTED TO CH5
 CONNECT SETUP EXIT
To fix the camera IP address, or allow the recorder to assign an IP address to your IP camera, select SETUP,
and select STATIC IP or DHCP for NETWORK TYPE.
Click APPLY and EXIT to save your changes.
SETUP
NETWORK TYPE DHCP
IP 10.1.1.14
PORT 80
USER NAME admin
PASSWORD *****
NETMASK 255.0.0.0
GATEWAY 10.1.1.10
PRIMARY DNS 168.95.1.1
EXIT