AXIOMTEK eBOX671-517-FL Series User manual

eBOX671-517-FL Series
Embedded System
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, or any liability arising from such uses.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update any information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in
any forms or by any means, electronic, mechanical, photocopying, recording, among others,
without prior written permissions of Axiomtek Co., Ltd.
Copyright 2019 Axiomtek Co., Ltd.
All Rights Reserved
April 2019, Version A1
Printed in Taiwan

iii
Safety Precautions
Before getting started, please read the following important safety precautions.
1. The eBOX671-517-FL does not come with an operating system which must be loaded
first before installation of any software into the computer.
2. Be sure to ground yourself to prevent static charge when installing any internal
components. Use a wrist grounding strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
3. Disconnect the power cord from the eBOX671-517-FL prior to making any installation.
Be sure both the system and all external devices are turned OFF. Sudden surge of
power could ruin sensitive components. Make sure the eBOX671-517-FL is properly
grounded.
4. Make sure the voltage of the power source is correct before connecting it to any power
outlet.
5. Turn Off system power before cleaning. Clean the system using a cloth only. Do not
spray any liquid cleaner directly onto the screen.
6. Do not leave equipment in an uncontrolled environment where the storage temperature
is below -40℃or above 80℃as it may damage the equipment.
7. Do not open the system’s back cover. If opening the cover for maintenance is a must,
only a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help discharge any static electricity on
human body.
When handling boards and components, wear a wrist grounding strap available from
most electronic component stores.
8. Note!! Caution with touch! eBOX671-517-FL will be hot when it's on.

iv
Classifications
1. Degree of production against electric shock: not classified
2. Degree of protection against ingress of water: IP40
3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air,
oxygen or nitrous oxide.
4. Mode of operation: Continuous

v
General Cleaning Tips
Please keep the following precautions in mind while understanding the details fully before and
during any cleaning of the computer and any components within.
A piece of dry cloth is ideal to clean the device.
1. Be cautious of any tiny removable components when using a vacuum cleaner to absorb
dirt on the floor.
2. Turn the system off before clean up the computer or any components within.
3. Avoid dropping any components inside the computer or getting circuit board damp or wet.
4. For cleaning, be cautious of all kinds of cleaning solvents or chemicals which may cause
allergy to certain individuals.
5. Keep foods, drinks or cigarettes away from the computer.
Cleaning Tools:
Although many companies have created products to help improve the process of cleaning
computer and peripherals, users can also use house hold items accordingly for cleaning.
Listed below are items available for cleaning computer or computer peripherals.
Pay special attention to components requiring designated products for cleaning as
mentioned below.
Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although
paper towels or tissues can be used on most hardware as well, it is recommended to use
a piece of cloth.
Water or rubbing alcohol: A piece of cloth may be somewhat moistened with water or
rubbing alcohol before being rubbed on the computer. Unknown solvents may be harmful
to plastic parts.
Absorb dust, dirt, hair, cigarette and other particles outside of a computer can be one of
the best methods of cleaning a computer. Over time these items may restrict the airflow
in a computer and cause circuitry to corrode.
Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are applicable to
reach areas in keyboard, mouse and other areas.
Foam swabs: If possible, it is better to use lint free swabs such as foam swabs.
.
【Note】: It is strongly recommended that customer should shut down the system before
start to clean any single components.
Please follow the steps below:
1. Close all application programs;
2. Close operating software;
3. Turn off power switch;
4. Remove all devices;
5. Pull out power cable.

vi
Scrap Computer Recycling
Please inform the nearest Axiomtek distributor as soon as possible for suitable solutions in
case computers require maintenance or repair; or for recycling in case computers are out of
order.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines
Corporation. Intel®and Pentium®are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and QuickBasic, Windows 10, Windows 8.1, Windows 8,
Windows 7, Windows XPE, Windows XP, Windows CE embedded, Linux are
trademarks of Microsoft Corporation.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

vii
Table of Contents
Disclaimers.............................................................................................................ii
Safety Precautions................................................................................................iii
Classifications.......................................................................................................iv
General Cleaning Tips ........................................................................................... v
Scrap Computer Recycling................................................................................... vi
SECTION 1 INTRODUCTION ........................................................................1
1.1 General Descriptions.........................................................................1
1.2 System Specifications.......................................................................2
1.2.1 CPU ...................................................................................................................2
1.2.2 I/O System ........................................................................................................3
1.2.3 System Specifications.....................................................................................4
1.2.4 Driver CD Contents..........................................................................................4
1.3 Dimensions ........................................................................................5
1.3.1 System Dimensions.........................................................................................5
1.3.2 Wall-mount Bracket Dimensions....................................................................6
1.4 I/O Outlets ..........................................................................................7
1.5Packing List........................................................................................8
1.6Model List........................................................................................... 8
SECTION 2 HARDWARE INSTALLATION....................................................9
2.1Installation of CPU............................................................................9
2.2Installation of 2.5" SATA Device.................................................... 12
2.3 Installation of SO-DIMM................................................................... 14
2.4Installation of Mini PCIe Module (Full-size) ................................... 15
2.5Installation of Flexible I/O Modules................................................ 17
SECTION 3 JUMPER & CONNECTOR SETTINGS ....................................19
3.1 Locations of Jumpers & Connectors............................................. 19
3.2 Summary of Jumper Settings ........................................................ 21
3.3 Connectors ..................................................................................... 22
3.2.1 DC-in Phoenix Power Connector .................................................................22
3.2.2 HDMI Connector.............................................................................................23
3.2.3 DVI-D ...............................................................................................................24
3.2.4 VGA .................................................................................................................24
3.2.5 Serial Port Connector(COM1~COM2) ..........................................................25
3.2.6 Ethernet Connector (LAN1~LAN8) ...............................................................25
3.2.7 USB 3.0 Connector ........................................................................................26
3.2.8 USB 2.0 Connector ........................................................................................26
3.2.9 Audio Connector............................................................................................27
3.2.10 Isolated Digital I/O .........................................................................................27
3.2.11 ATX Power On/OFF .......................................................................................27
3.2.12 Reset Button ..................................................................................................27
3.2.13 SATA Connector (SATA 1~2).........................................................................28
3.2.14 SATA Power Connector (CN18, CN19) .........................................................28
3.2.15 SIM Card Slots (S1~S2).................................................................................28

viii
3.2.16 Full-Size PCI Express Mini Card Slot (CN10 & CN12)................................29
3.2.17 Half-Size Mini Card Slot (CN15 & CN16)......................................................31
SECTION 4 BIOS SETUP UTILITY..............................................................33
4.1 Starting............................................................................................. 33
4.2 Navigation Keys............................................................................... 33
4.3 Main Menu........................................................................................ 34
4.4 Advanced Menu................................................................................35
4.5 Chipset Menu ...................................................................................49
4.6 Boot Menu........................................................................................ 54
4.7Save & Exit Menu............................................................................. 55
APPENDIX A WATCHDOG TIMER..............................................................57
About Watchdog Timer .................................................................................. 57
Sample Program.............................................................................................. 57
APPENDIX B DIGITAL I/O...........................................................................59
APPENDIX C CONFIGURING SATA FOR RAID.........................................63

eBOX671-517-FL Series user’s Manual
Introduction
1
SECTION 1
INTRODUCTION
This section contains general information and detailed specifications of the eBOX671-517-
FL.Section 1 consist of the following sub-sections:
General Descriptions
System Specifications
Dimensions
I/O Outlets
Packing List
Model List
1.1 General Descriptions
A fanless embedded system with 7th / 6th generation Intel® Core™ i7/i5/i3 and Celeron®
processor (formally codename: KabyLake / Skylake) processor with flexible I/O design. To
fulfill different application needs, the flexible embedded system supports WE8S, WES7,
Windows®10 and Linux, and it can be wall-mounted and Din-rail mounted by optional
requests.
The eBOX671-517-FL is built with an IP40-rated heavy-duty aluminum extrusion, enabling
reliable operation in harsh environments. Moreover, 24V DC power input with power protection,
-40°C to +70°C extended temperature*. To highly reduce deployment time, this fanless
embedded PC supports one optional I/O door for customers to easily install additional I/O
output. It is perfectly suitable for any industrial grade applications.
*. Please refer to 1.2.3 to check the operation temperature specification by the
corresponding processor.

eBOX671-517-FL Series user’s Manual
Introduction
2
Features
LGA1151 socket 7th / 6th generation Intel®Core™ i7/i5/i3 & Celeron®
-35/65 watt processor (Kaby Lake / Skylake) with Intel®Q170
Supports 8 channels gigabit PoE ports, IEEE802.3 af compliance
Supports Jumbo Frame (9.5k), WoL, PXE Remote Boot, Teaming
24V DC power input with optional ignition feature supported
Various of flexible I/O kit supported via Flexible I/O Window
Reliable and Stable Design
The embedded system supports 7th / 6th generation Intel®Core™ i7/i5/i3 and
Celeron®35W or 65W processor, high flexibility and multi-functional design is the
best solution for any industrial field applications.
Flexible Connectivity
It comes with rich I/O interfaces including dual RS-232/422/485 ports, four USB 3.0
ports, two USB 2.0 ports, 6-in/2-out isolated digital I/O and eight GbE/PoE LAN ports.
Embedded O.S. Supported
The eBOX671-517-FL with 6th platform supports Win 7/8/10 and Linux; 7th platform can
support Windows®10 64 Bit and Linux only.
Various Storage Supported
In terms of storage, the eBOX671-517-FL supports two 2.5" SATA storage drive bay, and one
mSATA device.
1.2 System Specifications
1.2.1 CPU
CPU
LGA1151 socket 7th / 6th generation Intel®Core™i7/i5/i3 & Celeron®processor, CPU
TDP max. up to 35W/65W
Intel® Core™ I7-6700TE/ 7700T/7700 processor
Intel® Core™ I5-6500TE/ 7500T/7500 processor
Intel® Core™ I3-6100TE/ 7101TE processor
Intel® Celeron®G3900TE / G4400TE processor
Chipset
Intel®Q170
BIOS
American Megatrends Inc. UEFI (Unified Extensible Firmware Interface) BIOS.
System Memory
Two 260-pin unbuffered DDR4-2133 MHz SO-DIMM socket, up to 32 GB at
the maximum for 6th generation Intel® Core™ processor
Two 260-pin unbuffered DDR4-2400 MHz SO-DIMM socket, up to 32 GB at
the maximum for 7th generation Intel® Core™ processor

eBOX671-517-FL Series user’s Manual
Introduction
3
1.2.2 I/O System
Display
1 x HDMI (Resolution:4K/2K@60Hz)
1 x DVI-D (Resolution:4K/2K@60Hz)
1 x VGA (Resolution: 1920X1200@60Hz)
【Note】: If users use HDMI /DVI monitor to install graphic driver, please press "win + P"
to "Clone Displays mode" and from Intel Graphics Control Panel -> Multiple Displays -> select
HDMI or DVI as the main screen.
Ethernet / Power over Ethernet
8 x 10/100/1000 RJ45 Ethernet ports(8 x i211-AT)
IEEE802.3af compliance, max. up to 90W for total 8-CH PoE
USB Ports
4 x USB 3.0
2 x USB 2.0
Serial Ports
2 x RS-232/422/485 (COM1~2)
DIO
Isolated 6 x DI and 2 x DO
Audio
1 x Audio (Mic-in/Line-out)
Mini Card Interface
2 x full-size PCI Express Mini Card Slots (USB + PCI Express)
1 x half-size PCI Express Mini Card Slots(mSATA + USB + PCI Express)
1 x half-size PCI Express Mini Card Slots(USB signal only)
Storage
2 x 2.5" SATA HDD/SSD drive bay
1 x mSATA (enabled in BIOS setting)
Indicator
1 x Green LED as indicator for PWR status
1 x Green LED as indicator for HDD active
2 x Green LED as indicator for programmable LED
Switch
1 x Power switch
1 x Reset switch
SIM & Antenna
2 x Front-access SIM slot
4 x SMA type antenna opening

eBOX671-517-FL Series user’s Manual
Introduction
4
1.2.3 System Specifications
Watchdog Timer
1~255 seconds or minutes; up to 255 levels.
Power Supply
24VDC input by terminal block connector
Operation Temperature
35W Tj=100°C CPU:
-40°C to +70°C (-40°F to +158°F) with W.T. SSD & DRAM
65W Tj=100°C CPU:
-40°C to +55°C (-40°F to +131°F) with W.T. SSD & DRAM
35W Tj=80°C CPU:
-40°C to +50°C (-40°F to +122°F) with W.T. SSD & DRAM
Storage Temperature
-40℃~+85℃(-40 ºF ~ 185ºF)
Humidity
10% ~ 95% (non-condensation)
Vibration Endurance
With SSD: 3Grm (5-500Hz, X, Y, Z directions)
Shock Test
With SSD: 50 G, IEC 60068-2-27, half sine, 11 ms duration
Weight
4.31 kg (9.5 lb) without package
5.1 kg (11.24 lb) with package
Dimension
280 mm (11.02") (W) x 210mm (8.26") (D) x 79.6 mm (3.13") (H)
1.2.4 Driver CD Contents
Ethernet
Chipset
Graphic
Serial Port
USB 3.0
Intel® ME
Audio
User Manual
Quick Manual
【Note】: All specifications and images are subject to change without notice.

eBOX671-517-FL Series user’s Manual
Introduction
5
1.3 Dimensions
The following diagrams show dimensions and outlines of the eBOX671-517-FL.
1.3.1 System Dimensions

eBOX671-517-FL Series user’s Manual
Introduction
6
1.3.2 Wall-mount Bracket Dimensions

eBOX671-517-FL Series user’s Manual
Introduction
7
1.4I/O Outlets
The following figures show I/O outlets on the eBOX671-517-FL.
Front View
Rear View

eBOX671-517-FL Series user’s Manual
Introduction
8
1.5 Packing List
The eBOX671-517-FL comes with the following bundle package:
eBOX671-517-FL System Unit x 1
Quick Installation Guide x 1
DVD x 1 (For Driver and Manual)
DRAM Thermal Pad (3T) x 2
Terminal Block (3P) x 1
DIO Connector x 1
CPU Grease x1
Foot Pad x 4
Screw pack x 1
1.6 Model List
eBOX671-517-FL-DC
Fanless embedded system with LGA1151 socket 7th/6th gen
Intel® Core™ i7/i5/i3 & Celeron® processors, Intel® Q170,
VGA, DVI-D, HDMI, 8-CH PoE, 6 USB and 24 VDC
Please contact Axiomtek’s distributors immediately in case any abovementioned items are
missing.

eBOX671-517-FL Series user’s Manual
Hardware Installation
9
SECTION 2
HARDWARE INSTALLATION
The eBOX671-517-FL is convenient for various hardware configurations, such as 35/65W
CPU, DRAM, HDD (Hard Disk Drive), SSD (Solid State Drive) and PCI Express Mini card
modules. Section 2 contains guidelines for hardware installation.
2.1 Installation of CPU
Step 1 Turn off the system and unplug the power cord.
Step 2 Loosen four screws to remove top cover.
Step 3 Remove the warning label and disengage load lever.
Disengage load lever by rele
Rotate load lever to open position at approximately 135°.
Rotate load plate to open position at approximately 150°.
Note
Apply pressure to corner with right-hand thumb when opening or
closing load lever - otherwise lever will bounce back (as a mouse trap)
causing bent contacts.

eBOX671-517-FL Series user’s Manual
Hardware Installation
10
Step 4 CPU installation steps:
Lift processor package from shipping media by grasping the substrate edges.
Scan the processor package gold pads for any presence of foreign material.
Locate connection 1 indicator on the processor which aligns with connection 1 indicator
chamfer on the socket, and notice processor keying features that line up with posts along
socket walls.
Grasp the processor with thumb and index finger along the top and bottom edges.
The socket will have cutouts for your fingers to fit into.
Carefully place the processor into the socket body vertically.
Caution
Never touch fragile socket contacts to avoid damage and do not touch processor
sensitive contacts at any time during installation.

eBOX671-517-FL Series user’s Manual
Hardware Installation
11
Step 5 Align pins of the CPU with pin holes of the socket. Be careful of the
CPU’s orientation that user’s need to align the arrow mark on the CPU
with the arrow key on the socket.
Step 6 And apply the thermal grease evenly on top of the processor.
Step 7 Put the top cover and fasten four screws back onto the system.

eBOX671-517-FL Series user’s Manual
Hardware Installation
12
2.2 Installation of 2.5" SATA Device
Step 1 Turn off the system and unplug the power cord.
Step 2 Turn the system upside down to locate seven screws at the bottom and
then loosen all screws.
Step 3 Open the bottom cover.
Step 4Locate SSD/HDD within the red line as marked.
Please notice the direction of connector for HDD.