baby&child ROSELLE CONVERSION CRIB 104857 User manual

CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to
the address above. Include the product model number, color, and a brief description of the part. Call 1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry
cloth. Blot spills immediately and wipe with a clean damp cloth. If the crib is to be stored, store in a cool dry place and
carefully package all original hardware to protect from loss.
TOOLS AND INSTALLATION
Tools
Necessary: Allen Key (included)
NOTE:
It may be easier to assemble product with two people.
NOTE:
When inserting bolts, turn clockwise until tight. Then loosen
12
-
34
of a turn. After crib is
completely assembled, return to each bolt and tighten. Use wax or soap on all bolts to facilitate assembly
Page 1 of 10
Made in Vietnam
Distributed in the U.S.A. by:
Restoration Hardware Baby & Child
11640 Harrel St. Suite B
Mira Loma, CA 91752
www.rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7
WARNING:
Read all
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE.
All Restoration Hardware cribs are designed to meet the highest safety
standards and comply with all U.S. and Canadian cribs and cradles regulations.
Model No. 104857
"ROSELLE CONVERSION CRIB"

IMPORTANT SAFETY INFORMATION FOR CRIBS
WARNING: Infants can suffocate on soft bedding. Never add a pillow or
comforter. Never place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly
instructions could result in serious injury or death.
•Never use plastic shipping bags or other plastic film as mattress covers because they can
cause suffocation.
•Infants can suffocate in gaps between crib sides and a mattress that is too small.
•To reduce the risk of SIDS, pediatricians recommend healthy infants to be placed on
their backs to sleep, unless otherwise approved by your physician.
Strangulation Hazard:
• Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as
hood strings or pacifier cords. DO NOT suspend strings over over a crib or attach strings to toys
•
.
•
To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on
loose fasteners.
• DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
• When a child is able to pull to a standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
• When child is able to climb out or reaches the height of 35 in (89 cm), the crib shall no longer be
used, and the child should be placed in a youth or regular bed.
• Check this product for damaged hardware, loose joints, missing parts or sharp edges before and
after assembly and frequently during use. DO NOT use crib if any parts are missing, damaged or
broken. Contact customer service at 1-800-762-1751 for replacement parts and instructional
literature if needed. DO NOT substitute parts.
•
DO NOT use a water mattress with this crib.
•
If refinishing, use a non-toxic finish specified for children’s products.
•
Follow warnings on all products in a crib.
• Never use plastic shopping bags or other plastic film as mattress covers because they can cause
suffocation.
•
Infants can suffocate in gaps between crib sides and a mattress that is too small.
Page 2 of 10

Page 3 of 10
IMPORTANT SAFETY INFORMATION FOR CRIBS
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST
27-1/4 INCHES BY 51-5/8 INCHES WITH A THICKNESS NOT EXCEEDING 6
INCHES.
WARNING
•DO NOT use this crib if the enclosed or attached instructions cannot be
strictly adhered to. DO NOT use this crib if the child is able to climb out
unaided or is taller than 90 cm. DO NOT place cords, straps or similar
items that could become wound around the child's neck in or near this crib.
Ensure that the sides are properly latched or locked in place when the crib
is occupied. The mattress used with this crib should not be more than 15
cm thick and should be of such length and width that the gap between the
mattress and the sides of the crib is not more than 3 cm when the
mattress is pushed into the corner of the crib.
•Parents should inspect the crib regularly before putting the child in the crib
each day and confirm that every component of the crib is properly and
securely in place.

Page 4 of 10
IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS
WARNING: ENTRAPMENT / STRANGULATION HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes may
strangle a child.
•The mattress intended for use on the bed shall be a full-size crib mattress
having minimum dimensions of 51-5/8 inches (1310mm) in length,
27-1/4 inches (690mm) in width and 4 inches (100 mm) in thickness, not
exceeding 6 inches (152 mm) in thickness.
•If guardrails are used as the mattress containment means, guardrail(s)
provided must be used to avoid the formation of a gap between the
mattress and the bed that could cause an entrapment.
•DO NOT place bed near windows where cords from blinds or drapes may
strangle a child.
•DO NOT place items with a string , cord, or ribbon around a child’s neck,
such as hood strings or pacifier cords.
•DO NOT suspend strings over a toddler bed for any pacifier cords.
•A child using the toddler or day bed shall be at least 15 months of age and
shall not weigh more than 50lbs (22.7kgs).

Page 5 of 10
STATIONARY
FRONT RAIL
END RAIL PANEL
MATTRESS SUPPORT
HEADBOARD
ITEM IDENTIFICATION
For ease of identification, all parts are labeled to correspond to the step number
in which the part is used.
STEP #1 Leg and Headboard assembly
End Rail Panels and Headboard assembly (Page 6 of 10)
STEP # 2 Mattress Support Arm assembly.
Stabilizer Rail assembly
Mattress height adjustment (Page 7 of 10)
STEP #3 Installation of Stabilizer Rail into the End Rail Panel (Page 8 of 10)
STEP #4 Stationary front Rail assembly (Page 9 of 10)
STEP #5 Toddler Rail assembly (Page 10 of 10)

DETAIL B
HARDWARE FOR STEP #1:
(DD) 1/4" x 1-3/4" BOLT = 04 pcs
(AA) 1/4" x 2-1/2" BOLT = 04 pcs
Page 6 of 10
STEP #1
LEG AND HEAD BOARD ASSEMBLY
END RAIL PANELS AND HEADBOARD
ASSEMBLY
STEP #1.1
Gently lay the Headboard and End Rail Panel
on their backs on a flat and nonabrasive
surface.
STEP #1.2
Align and insert the threaded rod of the Leg
into the holes and turn clockwise to tighten.
Please see DETAIL A.
Bring the Headboard and the End Rail Panel in
upright position.
NOTE:
On both ends of the Headboard are holes for
the bolt to pass through which correspond to
the holes located on both ends of the End rail
Panels with pre-installed nuts.
STEP #1.4
Align the hole of the End Rail Panel into the
hole of the Headboard then insert Allen Head
Bolt into hole and turn clockwise to tighten.
Tighten the bolt with Allen Wrench Provided.
Please see DETAIL B.
DETAIL A

Page 7 of 10
11 X 70
OPEN WRENCH
LOCK
WASHER
B
C
STEP #2
MATTRESS SUPPORT ARM ASSEMBLY
STABILIZER RAIL ASSEMBLY
MATTRESS HEIGHT ADJUSTMENT
STEP #2.1
Lay Mattress Support flat with Stabilizer Rail on each
side.
NOTE:
On each end of the arm of the Mattress Support, there
is a hole for the Allen Head Bolt to pass through that
corresponds to the holes located in the frame of the
Mattress Support.
STEP #2.2:
Insert the Allen Head Bolt into the desired hole of the
frame through the hole on the arm support. Fasten the
Allen Head Bolt with Plain Washer, Lock Washers and
Hexagonal Nut provided. Repeat procedure on other
arms of the Mattress Support. Please see DETAIL C.
WARNING:
Set the Mattress Support to the desired height by
adjusting the support arms. The Mattress Support
should be at its highest setting for newborns, and then
adjusted to the lower positions as the child grows and
becomes mobile. Once the child is able to stand, the
Mattress Support should be at its lowest position.
STEP #2.3:
Install the Stabilizer Rail at ends of the arm support as
illustrated on DETAIL D.
DETAIL C
DETAIL D
ALLEN WRENCH
(BB) 1-3/8" x 1/4" Ø Mattress Bolt = 8PCS
(BB) MATTRESS NUT = 8 PCS
(BB)PLAIN WASHER = 8 PCS
(BB)LOCK WASHER = 8 PCS
MATTRESS
NUT
PLAIN
WASHER
MATTRESS
BOLT
ALLEN
WRENCH
MATTRESS
BOLT
MATTRESS
BOLT
MATTRESS
BOLT
MATTRESS
BOLT
ALLEN WRENCH
OPEN WRECH
MATTRESS NUT
LOCK WASHER
PLAIN WASHER
MATTRESS
SUPPORT
STABILIZER RAIL
HARDWARE FOR STEP #2:

Page 8 of 10
STEP #3
STABILIZER RAILS INTO END RAIL PANEL
ASSEMBLY
STEP #3.1
On inside face of both End Rail Panel are
pre-installed metal brackets, designed to hold
the Stabilizer Rails. Set both ends of the
Stabilizer Rails into brackets as illustrated in
DETAIL E.
STEP #3.2
Once the Stabilizer Rails are set, gently tilt
the crib as illustrated in DETAIL F, and then
fasten the Stabilizer Rails with Allen Head
Bolt together with Plain Washer and Lock
Washer provided as illustrated in DETAIL G.
DETAIL E
DETAIL G
DETAIL F
HARDWARE FOR STEP #3:
(CC)Plain Washer (x4 pieces)
(CC)Lock Washer (x4 pieces)
(CC)1/4"Ø x 13/16" bolts (x 4 pieces)

Page 9 of 10
STEP #4
STATIONARY FRONT RAIL ASSEMBLY
Note: At both ends of the Stationary Front Rail
are holes for the bolt to pass through which
correspond with the holes on inside surface of
the End Rail Panel with pre-installed nut.
STEP #4.1
Align the hole of the Stationary Front Rail with
the hole of the End Rail Panel then insert the
Allen Head bolt into hole and turn clockwise
to tighten. Tighten the bolt with Allen Wrench
Provided. Please see DETAIL H.
After assembly re-tighten all bolts to snug fit.
DO NOT OVER TIGHTEN
DETAIL H
Allen Wrench (1 piece)
(DD) Lock washer (4 pieces)
(DD) 1/4"Ø x 1-3/4 inch bolts (x 4 pieces)
HARDWARE FOR STEP #4:

Page 10 of 10
STEP #5
TODDLER RAIL ASSEMBLY
STEP #5.1:
Remove one of the Stationary Front Rail of the crib by
loosening all the bolts installed as well as the Mattress
Support.
STEP #5.2:
Gently tilt the crib and release the bolts underneath the
metal brackets holding the Stabilizer Rails.
NOTE: If Mattress Support is not in the lowest position,
unscrew Mattress Support bolts and move to the lowest
position.
STEP #5.3
On inside face of both End Rail Panels are holes with insert
nut pre-installed and holes for the wooden dowels to pass
through which corresponds to the holes on both ends of
the Toddler Rail and pre-installed wooden dowel. Fasten
the Threaded Rod manually into the insert nut on both End
Rail Panels. Insert the wooden dowels of the Toddler Rail
into the hole of both End Rail Panel as well as the Threaded
Rod of End Rail Panels into the holes of the toddler Rail.
Insert Curved Washer, Lock Washer and engage
Hexagonal Nut. Tighten all the nuts with Wrench provided.
Please see DETAIL I
NOTE: Fill the holes located of the End Rail Panels with
Allen Head Bolt (DD) provided.
STEP #5.4
Repeat step #3. Installation of Stabilizer Rails into the Then
Panel (DETAIL J)
NOTE:
After assembly, re-tighten all bolts to a snug fit.
DD
14 X 90
OPEN WRENCH = 01
THREADED ROD = 4 PCS
CURVED WASHER = 4 PCS HEXAGONAL NUT = 4 PCS LOCK WASHER = 4 PCS (DD) 1/4" X 1/2" BOLT = 2 PCS
ALLEN WRENCH = 1
HARDWARE FOR STEP #5:
DETAIL I
DETAIL J
    
