Installation and Technical Information
BEGA
Due to the dynamic nature of lighting products and the associated technologies, luminaire data on this sheet is subject to change at the discretion of BEGA North America. For the most current technical data, please refer to bega-us.com
BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 © copyright BEGA 2020
Figure 1:
Figure 2a:
Figure 3:
Overview:
LED Watts: 5.8W
System Watts: 9.0W
Controllability: 0-10V dimmable
Weight: 2.2 lbs.
Protection Class: IP65
Tools Required:
• T10 torx head screwdriver
• T20 torx head screwdriver
• Flat head screwdriver
Figure 4:
Figure 2b:
Recessed wall luminaire - unshielded 24 215
Dimensions
A: 5-7/8”
B: 5-7/8”
C: 5-1/4”
Maintenance:
Clean regularly with solvent-free cleaner
removing dirt and debris. Do not use high
pressure cleaners.
Replacement Parts
See label inside of xture for LED replacement
part number.
Consult factory for all other replacement
components.
Accessories
Please refer to the appropriate accessory installation
sheet for further instruction when applicable.
Updated: 11/17/20
24 215 1 of 2
A C
B
Notice to Installer:
1. See page 2 for specic product safety warnings.
2. BEGA luminaires may be damaged if connected to conduit systems containing water -
Article 300-5G of National Electric Code requires that “Conduits or raceways through
which moisture may contact energized live parts shall be sealed or plugged at either or
both ends”
3. Luminaire is Non-IC rated. Insulation must be at least 3” from luminaire.
4. Suitable for installation in hollow wall construction or poured concrete construction.
5. Installation housing provided with (6) 1/2” NPT threaded conduit holes.
6. Installation housing must be installed so that the front face is ush with the nished wall.
7. Suitable for wall applications only. (No ceiling or in-grade applications).
BB24215 installation in hollow (stud) wall or masonry construction:
1. Install (2) slotted mounting brackets provided as shown in Figure 1, using the (4) self-
tapping T20 torx head screws provided with the included kit (Kit #93).
2. Adjust the brackets so that the front face of the installation housing will be ush with the
nished wall surface after installation, Figures 2a / 2b.
3. Secure the mounting brackets to wood or metal horizontal blocking using hardware (by
others) as shown in Figure 2a OR to masonry unit using hardware (by others) as shown in
Figure 2b.
4. Remove plastic insert.
5. Connect conduit to installation housing and pull wires for electrical connections to be
made later.
6. Replace plastic insert and nish wall.
BB24215 installation in poured concrete construction:
1. Remove plastic insert.
2. Install (4) threaded M4 rods into the installation housing and hand tighten until fully se-
cure, Figure 3.
3. Connect conduit to installation housing and pull wires for electrical connections to be
made later.
4. Replace plastic insert, rods will t through holes in plastic insert.
5. Attach the installation housing to concrete forms by using (8) wing nuts provided. Ensure
that the front face of the installation housing will be ush with the nished surface.
6. Pour concrete. Do not pump or drop concrete directly on top of the installation housing.
Doing so could deform or damage the installation housing.
7. After concrete has cured, remove wing nuts from threaded rods before removing the
forms.
24215 luminaire installation:
1. Remove plastic insert and debris from installation housing
2. Make wiring connection:
MAIN VOLTAGE SUPPLY WIRE TO BLACK DRIVER WIRE
NEUTRAL (COMMON) SUPPLY WIRE TO WHITE DRIVER WIRE
GREEN GROUND WIRE TO GREEN DRIVER WIRE
Dimming (if applicable):
DIMMING CONTROL WIRE (+) TO POSITIVE DRIVER DIM CONTROL WIRE
DIMMING CONTROL WIRE (-) TO NEGATIVE DRIVER DIM CONTROL WIRE
3. Put luminaire into installation housing and secure into place by evenly tightening the (2)
T10 torx head screws on the front of the luminaire to engage the clamping system.
Masonry bracket
Stud bracket
