BEGA 84 218 Manual

Installation and Technical Information
BEGA
Due to the dynamic nature of lighting products and the associated technologies, luminaire data on this sheet is subject to change at the discretion of BEGA North America. For the most current technical data, please refer to bega-us.com
BEGA 1000 Bega Way, Carpinteria, CA 93013 [phone] © copyright BEGA 2021
Figure 1: Product Diagram
Figure 2:Fixture Installation
Overview:
LED Watts: 4.2W
System Watts: 6.0W
Input Voltage: 12-24V AC
Weight: 7.5 lbs.
Protection Class: IP65
Tools Required:
• 3mm Hex Key
• Digging tool
18 16 14 12 10
40 46 73 116 185 294
30 61 97 155 246 392
20 92 146 232 369 588
15 122 195 309 492 784
10 183 292 464 738 1176
5 366 585 928 1477 2353
WireSize(AWG)
Max.RunLength(ft)PerWireSize:2Voltdrop
Connected
LEDWatts
Garden and pathway bollard – Direct burial anchorage 84 218
Dimensions
A: 4 3/8’’
B: 27 1/2’’
C: 4 3/8’’
Maintenance:
Clean regularly with solvent-free cleaner
removing dirt and debris. Do not use high
pressure cleaners.
Replacement Parts
See label inside of xture for LED replacement
part number.
Consult factory for all other replacement
components.
Accessories
Please refer to the appropriate accessory installation
sheet for further instruction when applicable.
Updated: 03/22/21
84 218 1 of 2
A C
B
D
Notice to Installer:
1. For use with 12-24V AC magnetic landscape transformers only.
2. Voltage must NOT drop below 10V at xture location.
3. Turn main power OFF before start of installation.
4. Luminaires most be installed 10 feet or more from pool, spa or fountain.
5. Wiring connection points must be made in a watertight location.
6. Anchorage tube length 11 3/4’’.
Installation: Luminaire
1. Establish an area for xture placement and prepare the soil for anchorage by digging
a hole (12” maximum depth).
2. Dig a trench from the anchorage hole to the power source. The depth of the trench
will be determined by national, state, and local codes.
3. Install at least 3” of pea gravel or similar in the bottom of the anchorage hole for
drainage.
4. Loosen (2) set screws on the garden bollard to release the anchorage post.
[Figure 1]
5. Bring 12-24V supply wiring into the bottom of the anchorage post and feed through
to the top until 12” of the cable comes up through the top of the anchorage post.
6. Bury supply wiring cable in trench.
7. Place anchorage post into the hole and ll in the hole with packed soil, ensuring that
the post is vertical and secure.
8. Make wire splices from supply wiring coming out of anchorage post to bollard wiring
coming down from bollard shaft. For maximum wire run lengths, see the table below.
9. Push splices into bollard shaft.
10. Mount the bollard onto the anchorage post until the bottom of the bollard hits the
ground. Tighten (2) set screws to secure bollard to anchorage shaft. [Figure 2]
11. Connect supply wiring to main power. Turn on the main power.
Set Screws
Anchorage
Supply Wiring

Installation and Technical Information
BEGA
Due to the dynamic nature of lighting products and the associated technologies, luminaire data on this sheet is subject to change at the discretion of BEGA North America. For the most current technical data, please refer to bega-us.com
BEGA 1000 Bega Way, Carpinteria, CA 93013 [phone] © copyright BEGA 2021
Product Safety Warnings:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
SUITABLE FOR WET LOCATIONS.
MIN 90°C SUPPLY CONDUCTORS.
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT
BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.
CONVIENT AUX EMPLACEMENTS MOUILLÉS.
LES FILS D’ALIMENTATION 90°C MIN.
Updated: 03/22/21
2 of 2
84 218
Garden and pathway bollard – Direct burial anchorage 84 218