BEMIS bioBidet DIB Special Edition User manual

1
OWNER’S MANUAL
DIB
Special Edition

2 3
PRODUCT INFORMATION
Safety Precautions...................................................4
Product Features.......................................................8
Unit & Parts..................................................................10
Dimensions...................................................................12
Remote Control.........................................................13
PRODUCT INSTALLATION
Installation....................................................................14
Remote Control Installation.................................16
Trial Operation............................................................18
Product Disassembly...............................................19
Operation.....................................................................22
TROUBLESHOOTING
Settings........................................................................30
Maintenance & Cleaning......................................34
Specifications............................................................36
Troubleshooting.......................................................37
Warranty.......................................................................38
TABLE OF CONTENTS

4 5
SAFETY PRECAUTIONS
THIS UNIT WAS MANUFACTURED FOR HOUSEHOLD USE ONLY.
READ ALL OPERATING INSTRUCTIONS BEFORE INSTALLATION.
•This product should be installed according to this manual.
•Please read this manual carefully and install properly.
•Please save this manual and place in easily accessible location.
•Do not attempt to service this appliance yourself.
Doing so will void warranty.
IMPORTANT SAFETY GUARDS
•In the case 120V 60 Hz: Power supply must be a 15 Amp GFCI outlet.
•The electrical cord must be connected to a GFCI outlet.
•The GFCL outlet should be 1ft. above the floor.
•Install only in well-ventilated areas to avoid excess humidity.
•Do not install in narrow toilet stalls or in shower stalls.
•Install only where direct contact with water is minimized.
•Do not install near any heat source.
•Avoid using extension cords if possible. Consult with a certified
electrician where extension cords are necessary.
DANGER - TO REDUCE THE RISK OF ELECTROCUTION
•Do not use while bathing.
•Do not place or store product where it can fall
or be pulled into a tub or sink
•Do not place in or drop into water or other liquid.
•Do not reach for a product that has fallen into water. Unplug immediately.
WARNING - TO REDUCE THE RISK OF BURNS,
ELECTROCUTION, FIRE, OR INJURY TO PERSONS
•Close supervision is necessary when this product is used
by, on, or near children or invalids.
•Use this product only for its intended use as described in this manual.
Do not use attachments not recommended by the manufacturer.
•Never operate this product if it has a damaged cord or plug, if it is not
working properly, has been dropped or damaged, or dipped into water.
Return the product to a service center for examination and repair.
•Keep the cord away from heated surfaces.
•Never drop or insert any objects into any opening or hose.
•Do not use outdoors or operate where aerosol (spray) products are
being used or where oxygen is being administered.
•Connect this product to a properly grounded outlet only.
See grounding instructions.
•Unplug this product before filling. Fill (reservoir) with water only.
SAVE THESE INSTRUCTIONS

6 7
SAFETY PRECAUTIONS (CONT.)
GROUNDING INSTRUCTIONS
DANGER - IMPROPER USE OF THE GROUNDING PLUG CAN
RESULT IN A RISK OR ELECTRIC SHOCK
This product has a three-prong grounding plug, which must be plugged into
an outlet that is properly installed and rounded. In the event of an electrical
short circuit, grounding reduces the risk of electric shock by providing an
escape wire for the electric current. If repair or replacement of the cord or
plug is necessary, do not connect the grounding wire to either flat blade
terminal. The wire with insulation having an outer surface that is green with or
without yellow stripes is the grounding wire. Check with a qualified electrician
or service person if the grounding instructions are not completely understood,
or if in doubt as to whether the product is properly grounded.
This product is for use on a nominal 120V circuit, and has a grounding plug
that looks like the plug illustrated in sketch A in Figure 1. A temporary adapter,
which looks like he adapter illustrated in sketches Band C, may be used to
connect this plug to a 2-pole receptacle as shown in sketch B if a properly
grounded outlet is not available.
The temporary adapter should be used only until a properly grounded outlet
(sketch A) can be installed by a qualified electrician. The green colored
rigid ear, lug, or the like extending from the adapter must be connected to a
permanent ground such as a properly grounded outlet box cover. Whenever
the adapter is used, it must be held place by the screw.
OPTIONAL GROUNDING INSTRUCTIONS

8 9
PRODUCT FEATURES
DIB Bidet has the following characteristics:
Continuous Warm Water Supply
Enjoy continuous warm water throughout
the wash cycle.
Bubble Wash
Aerated water wash adds cleaning comfort.
Pulse & Oscillate
Pulsating wash repeatedly cycles from weak
to strong. Nozzle moves back and forth for
massage effect.
Energy Saving Function
When activated, Energy Saving Mode will set
the heaters to a lower temperature to reduce
energy consumption.
Touch Panel Remote Control
Convenient touch screen remote control
provides easy user interface.
Vortex Wash
Soft but powerful water wash for added
cleansing benefit.
Stainless Steel Nozzle
For better hygiene, a stainless steel
nozzle is applied.
Deodorization Function
Deodorizing filter eliminates odors efficiently.
Child Settings
Optimized nozzle position and
water pressure for children.
User Preset
User can preset and store the
memory for control settings.

10 11
UNIT & PARTS
Cone
packingBolt guides
Mounting bolt
s
Remo
te control AAA 4 batteries
Remote control
bracket
Mounting
bracket
Water supply hose
(for toilet) Water supply hose (for bidet)

12 13
REMOTE CONTROLDIMENSIONS
Elongated Round

14 15
INSTALLATION
1. Toilet Seat Removal 2. Turn Off Shut-Off Valve
3. Connect T-Valve 4. Water Supply Hose
•Lift hinge covers and use a
screwdriver to remove the
mounting bolts.
•Remove the toilet seat. Steps
may vary by type of seat.
•Connect T-Valve to water
supply line and toilet tank.
•Remove existing water
supply hose.
•Connect water supply
hose for toilet.
•Turn shut-off
valve completely.
•Flush toilet and hold
down handle to completely
empty tank.
5. Install Mounting Bracket 6. Slide Seat onto Plate
7. Connect Bidet hose 8. Insert Deodorizing
Cartridge
•Place adjustable mounting
plate over mounting holes
on toilet, flat side down,
rubber side off mounting
plate should be closet to
the toilet tank.
•Connect bidet hose,
making sure the hose is
firmly connected.
•Do not twist bidet hose,
excessively bend it, or strip
the plastic screw threads.
•Slide seat onto plate until it is
secure and “clicks” into place.

16 17
REMOTE CONTROL INSTALLATION
•Remove the adhesive
protection to attach the
remote control bracket to
the wall or other surfaces.
•Turn remove over and open
the battery compartment.
Inset four “AAA” type
batteries (included) as
indicated inside battery
compartment and replace
battery cover.
•Identify a location in the
bathroom for the remote
control that is visible and
reachable from the toilet and
mount remote using double
stick tape (included).
•Clean the area thoroughly
before attaching the bracket.
1. Remove Adhesive 2. Clean Area
3. Batteries 4. Mount Remote (Optional)
5. Battery Life 6. Unplug If Unit Does
Not Work
•When the batteries have
reached the end of service
life, all LEDs will blink.
Replace the batteries with
new AAA size (4pcs).
•CAUTION - Do not use old
and new batteries together.
This could cause damage or
failure of the remote control.
•If the unit does not work
after replacing the batteries,
unplug and wait for 3
seconds. Plug in again.
•After replacing the batteries,
ID of the unit will be
initialized as “00” and its
ID will be equalized ID of
the remote control that
reaches the unit first. This
ID assigning function will
be needed to prevent signal
interruption if more than 2
units are used at one place.
In case of using one unit only,
no setting is needed.

18 19
TRIAL OPERATION
•Open the water supply
valve by turning it
counterclockwise.
•Be sure that the nozzle
comes out and retracts
when powered on.
•Don’t plug the power cord
with wet hands. Risk of
electric shock.
•Place your hand on the
occupied sensor of the seat.
The unit will fill with water.
Check if water comes out
from drain hold next to the
nozzle for 1-2 seconds.
•Check that there are no leaks
around the hose connection.
1. Open Water Supply 2. Check For Leaks
3. Nozzle 4. Test
PRODUCT DISASSEMBLY
1. Unplug Power 2. Close Water Supply Valve
3. Drain Water 4. Release & Remove
•Unplug the power
plug from the outlet.
•Press and release/drain
button on the side of bidet.
Completely drain the water
out of the main body. While
pressing the button, pull the
main body forward and then
remove it from the toilet.
•Release the nuts, and then
remove the brackets from
the toilet.
•Close the water supply valve
by turning it clockwise.
Completely drain out the
toilet water tank, release the
nuts at bidet body of the
bidet hose, and then remove
them from the main body.

20 21
•Open the water
supply valve by turning
it counterclockwise.
•Attach the toilet seat and
cover that were removed
when the bidet was installed.
•Remove the bidet hose,
toilet hose and T-Valve.
•Connect the water supply
hose that was removed when
the bidet was installed.
5. Remove Bidet Hose 6. Connect Water
Supply Hose
7. Open Water Supply Valve 8. Attach Toilet Seat
PRODUCT DISASSEMBLY (CONT.)

22 23
OPERATION
1. Sit On Toilet Seat 2. Press Posterior, Feminine,
and Vortex Wash Buttons
3. Press Dry Button 4. Press STOP Button
•Deodorization function
starts automatically.
•Dryer temperature is
adjustable. (5 levels)
•Selected function may be
used for up to 3 minutes.
•Dryer effect will be improved
if you wipe the moisture
lightly before operating the
drying function.
•Selected functions stop.
•Press STOP on the side
control panel for 3 seconds
to turn off the unit.
•Selected function can be
used as described. When
selecting VORTEX WASH
function, Oscillate function
cannot be used). When
selecting Child function,
VORTEX WASH function
may not operate).
•Dib’s specialized water spray
in VORTEX WASH function
enters into rectum, and then
helps relieve constipation and
fecal stasis.
•Unless STOP button is
pressed after Posterior and
Feminine function, the dryer
will start automatically.

24 25
5. Wide Clean (Oscillation) 6. Massage (Pulse) 7. Water Pressure Control 8. Nozzle Position Control
•When pressing the Wide
Clean button during the
operation of Posterior and
Feminine, nozzle will move
back and forth to wash a
wider range.
•When pressing the Child
button during the operation
of Wide Clean, the nozzle
position can be adjusted
in 5 positions.
•Wide Clean function will not
operate during the operation
of Vortex wash.
•When pressing Massage
button during operation
of Posterior, Feminine, and
Vortex wash, water pressure
will repeat high and low for
smooth pulsating wash.
•Adjust Water Pressure. •During the operation of
Posterior, Feminine, and
Vortex wash, nozzle position
can be adjusted by
pressing < or >.
OPERATION (CONT.)

26 27
11. Water Temperature Control 12. Energy Saving Modes
•Temperature of water can
be adjusted to the desired
level by pressing Seat
temp. Button.
•Room temp
Low - Middle - High
Automatic Energy Save Mode
•This mode will be activated
by pressing the Energy
Saving button until yellow
LED lamp lights on.
•Seat will be kept at 32C.
Smart Energy Save Mode
•This mode will be activated
by pressing the Energy
Saving button until green
LED lights on.
•Seat temperature will be
kept at 32C when it is not
occupied and raised back
to preset level according to
memorized time of use.
•It may take 5-7 days to
let the unit memorize the
usage pattern.
Cancel Energy Save Mode
•Press the Energy Saving
Button until LED is off
to release the energy
save modes.
This unit adopts the instant
heating technology for water
heating and does not consume
energy for water heating when
it is in stand by mode.
OPERATION (CONT.)
9. Child Function 10. Seat Temperature Control
•Press the Child
button to activate.
•Nozzle position will be
one level move forward
than normal.
•Water pressure will be one
level weaker than normal.
•Seat temperature will be one
level lower than normal.
•Vortex wash will not
operate while Child
mode is activating.
•Temperature of seat can
be adjusted to the desired
level by pressing Seat
temp. button.
•Room temp
Low - Middle - High

28 29
13. Deodorizing Function 14. Low Temperature
Burn Protection
15. User Preset
•When sitting on the
seat, deodorizing function
starts automatically.
•Speed of deodorizing fan can
be controlled. (Refer to the
User setting facilities).
•After leaving the seat,
the deodorizing function
will operate for 1
additional minute.
•To reduce the chance of
low temperature buns, the
seat has a seat heater auto
adjustment function which
turns on low temperature
(32C, 90F) when
user sits on the seat
for more than 15
minutes consecutively.
•Nozzle position, water pressure,
dry/water/seat temperature can
be present and stored for
2 different users.
How to Preset
1. Adjust nozzle position, water pressure,
dry/water/seat temperature to
your preference.
2. Press the STOP button or wait. Red
activating indicator will blink for 5
seconds when setting is completed.
Using the Preset Feature
1. Press selected preset button
2. Preset nozzle position, water pressure,
and temperatures will be activated.
OPERATION (CONT.)

30 31
SETTINGS
Function Seat
Status
Switch
Operation Description Initial Status
1On/Off
Automatic
Deodorizer
Fan
Press the “Stop”
and “Energy Saving”
for 3 seconds. Then
adjust the fan speed
by pressing “-” or “+”
button. Leave the
remote control alone
for 5 seconds to
complete
the setting.
High Speed in
Both Modes
2
Setting the
ID of
Remote
Control
Press the “Wide
Clean” button for
3 seconds. Then
set the ID 0-3 by
pressing “-” or “+”.
Leave the remote
control alone for
5 seconds to set
the ID.
ID “0”
3On/Off
Night Light
Press “+” button
for seconds.
Night light can be turned on and off by
pressing “+” button on the remote.
Night Light
is turned on
Level
Fan Speed Display of
activating
indicator
Energy
saving
(blinking)
Occu. Unocc.
default High High Blinking Red
0 Off Off Blinking Off
1Low Low Blinking Blue
2Low High Blinking Purple
3 High High Blinking Red
Level Display of
activating
indicator
Display of Seat
temperature (blinking)
default - -
0 Blinking Off
1 Blinking Blue
2 Blinking Purple
3 Blinking Red
Seat Switch ‘Off’ Status
Seat Switch ‘On’ Status
Regardless of On/Off
User Setting With Remote Control

32 33
Using Inline Carbon Filter
Use of external water filter is only recommended in areas with known hard
water issues. If a filter is used, it must be replaced every 3 months. This
product is designed and intended for use exclusively with Bio Bidet DIB water
filters. The purchase or use of any other water filter is not the responsibility of
BBC Innovation LLC. As such, any use of non DIB water filters is prohibited
and will void the warranty for those Bio Bidet products. Bio Bidet will not
be responsible for any resulting damages or claims related to the misuse or
distribution of non Bio Bidet DIB filters.
Function Seat
Status
Switch
Operation
Description
1Manual
Nozzle
Cleaning
Press “Posterior”
for longer than
3 second
Nozzle will
move forward
for cleaning
2 Power Off Press “STOP”
Nozzle will
retract and
clean itself
3 Factory
Default
Setting
Press “STOP” for
longer than 5
seconds
Press one
of “Stop”,
“Posterior”,
or“Feminine”
to power on
4 Selecting/
Canceling
Silent
Mode
Press “Feminine”
for longer than 3
seconds
To on/off the
chime sound.
Seat Switch ‘Off’ Status
Seat Switch ‘On’ Status
Regardless of On/Off
Extra Functions With Side Control Panel
SETTINGS (CONT.)

34 35
MAINTENANCE & CLEANING
Manual Nozzle Cleaning Cleaning of Bidet Body Drain Remaining Water Maintenance During Winter
1. Press Posterior for longer
than 3 seconds, and then
nozzle will extract and stop
(for 2 minutes).
2. Clean the nozzle with an
unused toothbrush, etc., and
press STOP. Nozzle
will retract.
1. Remove the power plug
from the outlet.
2. Close the water feed valve by
turning it counterclockwise.
3. Press the button on the side
of the main body to drain
the water.
1. Insert the power plug into
the outlet and be sure if the
power is supplied.
2. When the dib will not be
used for a long time (more
than a few days), close the
water shut off valve and drain
the water from the bidet.
1. Exterior surface of bidet is
made of plastic material,
which may be damaged by
scrubber, chemicals, etc.
2. Wipe the surface with a soft
damp cloth. Do not spray
water directly onto surface.
3. Clean the body after
removing the power plug
from the outlet. Be sure
no water plashes onto
the power plug or outlet.
4. Do not touch the power
outlet with wet hands.
Risk of electric shock.

3736
SPECIFICATIONS
ITEM DIB-850
Rated Voltage AC 120V, 60Hz
Max. Consumption Power 1270W
Power Cord Length 4ft.
Water Feed Method Directly Connected to Water Pipe
Water Pressure 9.9 - 106.6 psi
Wash
Feeding
Volume
Posterior 0.16 gal/min
Feminine 0.16 gal/min
Vortex 0.16 gal/min
Water Pressure Control 5-Step Control
Temp. Control Room Temp. ~ 100F
Heat Capacity 1200 W
Safety Device Temp. Fuse, Thermo Switch
Heated Seat
Temp. Control Room Temp. ~ 107F
Heater Capacity 55W
Safety Device Temp. Fuse
Dry
Temp. Control Room Temp. ~ 122F
Heater Capacity 250W
Safety Device Temp. Fuse, Bi-metal
Deodorization Catalytic Deodorization
Product
Dimension
inch (mm)
Elongated 15.9” (406) x 20.8” (528) x 6.5”
(165)
Round 15.9” (406) x 19.5” (496) x 6.5”
(165)
Product
Weight/
Gross Weight
lb (kg)
Elongated 10.8 (4.9 kg)/17.4 (7.9 kg)
Round 10.6 (4.9 kg)/17.2 (7.8 kg)
TROUBLESHOOTING
Problem Check List
The bidet is
not working
Check if the power plug is not connected.
Check for power failure.
Water does
not spray
Check if the water supply is suspended.
Check if the water supply is suspended.
Check if the nozzle is locked by foreign materials.
Check if connection hose is bent.
Water
pressure is
low
Check if the water pressure is set at too low level
Water is not
warm enough
Check if its temperature is set at ‘off’ or ‘low’
Check if energy save mode is on.
Seat is not
warm enough
Check if its temperature is set at ‘off’ or ‘low’
Check if energy save mode is on.
Vortex wash
is not
operated
Check if it is set on CHILD mode.
Check if energy save mode is on.
Please check the following points before
requesting the repair of the product.

38 39
1 YEAR WARRANTY
Bio Bidet warrants its products to be free from manufacturing defects under
normal use and service for a period of 1 year from the date of purchase. This
warranty is extended only to the original purchaser.
For full warranty details, visit www.biobidet.com
Contact Bio Bidet customer support with any questions you may have.
847.458.2334
[email protected]om
www.biobidet.com
WARRANTY