Berker 8536 52 00 User manual

ech30%
angle α
α
α
Description
Detection zone
Installation
Adjustments
Shutters
Angle fixing support 8590 02 00
Optimal installation height is 2.5m.
The detection zone shall remain free of obstacle.
m 8 m 16
h
h
h
2,5 m
2,5 m
ech40%
2,5 m
8 m
0,5 m 16 m
m 2,5
m 0,5
m 16
m 4
LED A LED B
Delay
(lighting time)
Brightness
level
Sensitivity
(change
of range)
1
2
IP55
IP55
+ 90°/- 30°
+/-80°
IP55
+ 90°/- 30°
+/-80°
Wall fixing plate Adjustment potentiometers
Directional detection head
Vertical adjustment
Button J
cfg
cfgcfg
cfg cfg
version à pile version solaire
LED cfg
Button J
Test and validation of detection
zone
Set potentiometer 2to mode "auto test".
OThe test mode is available only once the
product has been configured.
The Test mode is available for 3 minutes time
and does not take brightness level into
account.
Each detected movement turns LED Aon for
2 seconds.
The associated receiver is controlled.
After 3 minutes without detection, the product
is set back to auto mode.
Limitation of detection zone :
You can limit the detection zone using the
shutters supplied or by inclining the head.
Mounting
Projection or ceiling mount :
- Fix the wall plate using the supplied screws.
- Clip the detector onto the wall plate
- Tighten the screws to close.
For angle mounting, the wall fixing plate is
fitted between the accessory and
the detector.
Precautions for installation
For optimum detection conditions, please fol-
low these recommendations :
- Keep the detector protected from bad
weather, as it is sensitive to these conditions.
- Maintain 1m distance between the light
source and the detector and keep the detec-
tor out of the light source.
Product Description and working
principles
This detector allows remotely control of one
or more receivers for a given time when a
movement is detected in its detection zone.
This product can be used in two types of
configuration: one detector controls one/seve-
ral receiver(s); several transmitters control the
receiver(s).
Operation
The receiver(s) is(are) under control as soon
as the brightness level as set by potentiometer
2is considered too low and a movement is
detected.
Upon detection, the time delay is restarted.
If LED Aflashes quickly during configuration,
the position of potentiometer 1is not compa-
tible with the selected function.
Product factory reset is recommended before
any new configuration.
Factory reset
Keep push-button Jdepressed until LED
cfg flashes (>10s), and then release it.
LED cfg is turned o when factory return is
completed.
After factory return, wait 15 s before starting
configuration.
Action Adjustments Potentiometer
Use Auto (factory)
settings to set
automatic lighting
turn-on for
a given time.
Only available when
a detector’s time
delay is set.
Auto Settings
Put the Lux potentiometer on
“auto test”.
The settings are predefined :
Lux = ,
(operating at night only)
time = 3 min,
sensitivity = max
Turn automatic
lighting on for
a given time.
Only available when
a detector’s time
delay is set.
Installer settings
Adjust sensitivity. Allows setting the range
to avoid disturbance.
Configuration (button J)
These detectors can be configured in 3 dierent
ways :
• quicklink&: configuration without tool, directly
on the device via Jbutton and LED (see confi-
guration instructions quicklink&).
• tebis TX: configuration using connection device
from Hager
• ETS3/ETS4 via KNX-RF/TP gateway: database
and description of application software available
from the manufacturer.
Configuration by ETS
Press Jbutton for addressing by means of radio/
KNX gateway.
OProduct factory reset is required to change
the configuration mode.
Order no.
8536 52 00
Operation instructions
KNX-RF controller 220° solar
6LE003100C
zCaution:
- This device must be installed only by
a qualified electrician according to the
installation standards in force in the
country.
Correct Disposal of This product
(Waste Electrical & Electronic
Equipment).
(Applicable in the European Union and other European
countries with separate collection systems).
This marking shown on the product or its literature
indicates that it hould not be disposed with other
household wasted at the end of its working life. To
prevent possible harm to the environment or human
health from uncontrolled waste disposal, please
separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of
material resources.
Household users should contact either the retailer
where they purchased this product, or their local
government oce, for details of where and how they
can take this item for environmentally safe recycling.
Business users should contact their supplier and
check the terms and conditions of the purchase
contract. This product should not be mixed with other
commercial wastes of disposal.
Usable throughout Europe å and in Switzerland
Hager Controls hereby declares that the Operation
instructions 8536 52 00 device complies with the essential
requirements and other relevant provisions of Directive
2014/53/EU.
The CE declaration is available on the:
www.hagergroup.com
01 6LE003100C 02 6LE003100C

Other devices can be added to the installation.
Various configuration options are available
When a detector is associated with a receiver,
only 2 functions are available, depending on
potentiometer’s position :
Setting detector’s delay Setting receiver’s delay
TU4xx
1 detector 8536 52 00
+
1 receiver
Recommended configuration :
1. Set the potentiometer to a value dierent
from
2. Configure ON/OFF switch function (see
configuration instructions quicklink&)
1. Set the potentiometer to position
2. Configure the "timer"
(see configuration instructions quicklink&)
TU4xx
1 detector 8536 52 00
+
several receivers
1. Set the potentiometer to a value dierent
from
2. Configure the ON/OFF switch function (see
configuration instructions quicklink&)
on each receiver
In order to have a dierent delay on each recei-
ver :
1. Set the potentiometer to position
2. Configure the "timer" function
(see configuration instructions quicklink&)
TU4xx
Several detectors
8536 52 00
+
1 or several
receivers
Not recommended (conflict of delays) 1. Set the potentiometer to position on both
detectors.
2. Configure the "timer" function
(see configuration instructions quicklink&)
on each receiver
TU4xx
1 detector 8536 52 00
+
1 or several
transmitters
other than detectors
+
1 or several
receivers
Timer function being not used on the other
transmitter(s) :
1. Set the potentiometer to a value dierent
from
2. Configure the other transmitter(s)
(see configuration instructions quicklink&)
with a function other than timer.
Timer function used on the other transmitters :
1. Set the potentiometer to position
2. Configure the "timer" function
(see configuration instructions quicklink&)
on each receiver for each transmitter involved
Note : During configuration of a detector, Step 2 of the configuration instructions quicklink& shall be ignored.
TROUBLESHOOTING...
Problem Causes solutions
Unwanted lamp
switch on.
- Permanent heat source is active in the detection area (trees, bushes
shook by wind or presence of dogs, cats in the detection area).
- The detector is located on top a ventilation grill.
- Limit detector’s range by adjusting its inclination or by fitting shut-
tering blades to the lens, or by lowering sensitivity using the
adjustment knob.
- Move the detector to another location.
The range of
the detector is
too narrow.
- Detector’s installation height is not suitable (too high or too low).
- Sloppy ground.
- Modify installation height (2.5 m is optimal).
- Adjust detector’s direction.
Moving vehicle or
person is not
detected.
- Vehicle’s motor is not enough yet (heat radiation is too weak).
- People move forwards in front of detector.
- Detector energy too low.
- Install the detector in such a way that objects move within the area
in transverse direction.
- Place detector in a suitable location with solar cell directed towar-
ds the sun.
Technical specifications
Electrical specifications
Power Supply :Solar
Operational characteristics
Dimensions (L x w x h) : 153 x 91 x 130 mm
Luminosity threshold : 5 … 1000 Lux
Fixed time : 30 s … 15 min
Sensitivity : min. 20%, max. 100%
Limiting the detection zone : adjustable shutters
supplied
Transmission frequency : 868-868.6 MHz
Power émission : 25mW
Receiver category : 2
RF KNX Communication Media : RF1.R
Configuration mode : Quicklink, Easy link Controller,
ETS via media coupler
Range : 100 m on open field
Fixing accessories : corner support
(sold separately) Order no. 8590 02 00
Environment
Operating temperature : -20 … +55 °C
Storage temperature : -20 … +60 °C
IK : 04
Protection class : IP55
Resistance to fire : 750 °C
- (Red/Green LED) or timer (Red flashing LED)
according to the case
- Delete (LED is OFF)
The receiver will oer only the function set by the
potentiometer.
When a product is factory reset,
pre-configuration is removed.
It should then be configured again.
6LE003100C - 10/2021
03 Berker GmbH & Co. KG - Zum Gunterstal - 66440 Blieskastel/Germany - Tel.: [phone] - Fax: [phone] - E-Mail: [e-mail] - www.berker.com