BLK BOX 21-0730 User manual

OWNERS MANUAL & QUICK START GUIDE
BLACKOUT POWER RACK
NOTE : PLEASE READ ALL THE INSTRUCTIONS
CAREFULLY BEFORE ASSEMBLING THIS PRODUCT.
BLK BOX
21-0730
#MADEINBELFAST
105kg
PRODUCT WEIGHT
MAX USER WEIGHT
MAX USER
MAX TRAINING WEIGHT
DIMENSIONS
SAFE WORKING ZONE
- 125kg
300kg
1320mmx1320mmx2208mm
-
-
-
- 2000mmx2400mmx2700mm
1
-
PRODUCT SPECIFICATION

WARNING
TOOLS REQUIRED PARTS & ATTACHMENTS
Name SKU QTY
1 BLACKOUT POWER RACK UPRIGHT 21-0739 4
2 GOLIATH 1.2 SINGLE BAR CM 21-0015 1
3 1.2 BOX CM 21-0013 5
4 J-HOOK PAIR 16-0001 1
5 M10 SLEEVE ANCHOR BOLT 10-0031 12
6 M10X90 BOLT 10-0008 24
7 M10 FLAT WASHER 10-0019 60
8 M10 NYLOCK NUT 10-0024 24
1
2
3
6
8
5
SERIOUS OR FATAL INJURIES MAY OCCUR FROM INCORRECTLY ASSEMBLED EQUIPMENT. ALWAYS
ENSURE BOLTS ARE TIGHTENED CORRECTLY AND ALL PARTS ARE LEVEL AND PLUMB. TO FURTHER
REDUCE RISK OF INJURIES OR DEATH PLEASE USE OUR SUGGESTED TOOLS AND PERSONAL PRO-
TECTIVE EQUIPMENT (PPE). WE SUGGEST THAT A MINIMUM OF THREE PEOPLE ARE INVOLVED IN
THE ASSEMBLY OF THIS PRODUCT. EACH PERSON SHOULD BE EQUIPPED WITH SAFETY GLASSES,
STEEL TOE CAP BOOTS AND EAR PLUGS.
PLEASE BE AWARE OF THIS SYMBOL AS AN INDICATION TO CHECK THAT A PART IS
LEVEL OR PLUMB.
THIS SYMBOL IS AN INDICATION OF THE RECOMMENDED TORQUE EACH
BOLT SHOULD BE TIGHTENED TO. THIS VALUE WILL BE DEPENDENT ON
THE BOLT TYPE. PLEASE HAND TIGHTEN ALL BOLTS UNTIL YOU SEE THIS SYMBOL.
#MADEINBELFAST
xx
Nm
7
SPIRIT LEVEL
10MM MASONRY
DRILL BIT
17MM SPANNER X2
13MM SPANNER
HAMMER
HAMMER DRILL VACUUM STEP LADDER
4

ASSEMBLY
1
BOLT 2QTY 1.2 BOX CM (21-0013) TO 2QTY POWER RACK UPRIGHT (21-0739) WITH
BOLT ASSEMBLY AS SHOWN.
REPEAT ABOVE STEP.
#MADEINBELFAST
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024

2
BOLT 1QTY 1.2 BOX CM (21-0013) TO 2QTY BACK UPRIGHT (21-0739) WITH BOLT ASSEMBLY
AS SHOWN.
BOLT 1QTY 1.2 SINGLE BAR (21-0015) TO 2QTY FRONT UPRIGHT (21-0740) WITH BOLT
ASSEMBLY AS SHOWN.
ENSURE THAT ALL BLK BOX LOGOS ARE FACING OUTWARDS AND BOLTS ARE FACING IN-
WARDS.
#MADEINBELFAST
10.0008
10.0019 x2
10.0024

3TIGHTEN ALL BOLT ASSEMBLIES TO THE SPECIFIED TORQUE.
ENSURE UPRIGHTS ARE PLUMB AND ALL SINGLE BARS ARE LEVEL.
DRILL AND SECURE UPRIGHTS AS SHOWN IN 4 STEP FLOOR MOUNTING GUIDE BELOW.
#MADEINBELFAST
VACUUM
DRILL HOLE
90MM
1. DRILL 10MM HOLE, 90MM DEEP USING PLATE AS A GUIDE.
2. VACUUM OUT THE DUST.
FLOOR MOUNTING
HAMMER IN
BOLT TIGHTEN
3. HAMMER SLEEVE ANCHOR INTO THE HOLE.
4. TIGHTEN SLEEVE ANCHOR TO SPECIFIED TORQUE
USING13MM SPANNER.
30
Nm
xx
Nm
30
10.0031
10.0019

#MADEINBELFAST
1:1 SCALE FASTENERS
FOR TERMS AND CONDITIONS VISIT OUR WEBSITE AT:
www.blkboxtness.com/pages/terms-conditions
GET IN TOUCH:
TEL: [phone]
EMAIL: info@blkboxtness.com
DISCOVER MORE AT:
www.blkboxtness.com
M10x80 SLEEVE ANCHOR
10-0031
M10x90 BOLT
10-0008
NYLOCK NUT
10-0024
M10 FLAT WASHER
10-0019