BLK BOX SAMSON 21-0155 User manual

OWNERS MANUAL & QUICK START GUIDE
SAMSON HALF RACK
NOTE : PLEASE READ ALL THE INSTRUCTIONS
CAREFULLY BEFORE ASSEMBLING THIS PRODUCT.
BLK BOX
PRODUCT SPECIFICATION
PRODUCT WEIGHT
MAX USER WEIGHT
MAX TRAINING WEIGHT
DIMENSIONS
SAFE WORKING ZONE
-175kg
150kg
450kg
1900mm x 800mm x 2550mm
-
-
-
21-0155
-2900mm x 1800mm x 3000mm
#MADEINBELFAST

WARNING
xx
Nm
SPIRIT LEVEL
10MM MASONRY
DRILL BIT
TOOLS REQUIRED
17MM SPANNER X2
13MM SPANNER
HAMMER
HAMMER DRILL VACUUM STEP LADDER
PARTS & ATTACHMENTS
No. Name SKU QTY
1 UPRIGHT WITH FEET DNA80 21-0058 2
2 WESTSIDE UPRIHT WITH
FEET DNA80
21-0059
21-0060
1
1
3 1.2 BRANDING BOX CM
DNA80
21-0047 1
4 1.2 BOX CM DNA80 21-0045 2
5 0.4 BOX CM DNA80 21-0043 4
6 MULTIGRIPS DNA80 21-0165 1
7 J-HOOKS PAIR 16-0002 1
8 M20X120 BOLT 10-0010 54
9 M10X80 SLEEVE ANCHOR 10-0031 12
10 M20 FLAT WASHER 10-0023 108
11 M20 NYLOCK NUT 10-0028 54
12 UTILITY PEG DNA80 21-0234 8
13 M10 WASHER 10-0019 12
1
2
3
4
6
7
SERIOUS OR FATAL INJURIES MAY OCCUR FROM INCORRECTLY ASSEMBLED EQUIPMENT. ALWAYS ENSURE
BOLTS ARE TIGHTENED CORRECTLY AND ALL PARTS ARE LEVEL AND PLUMB. TO FURTHER REDUCE RISK OF
INJURIES OR DEATH PLEASE USE OUR SUGGESTED TOOLS AND PERSONAL PROTECTIVE EQUIPMENT (PPE).
WE SUGGEST THAT A MINIMUM OF THREE PEOPLE ARE INVOLVED IN THE ASSEMBLY OF THIS PRODUCT.
EACH PERSON SHOULD BE EQUIPPED WITH SAFETY GLASSES, STEEL TOE CAP BOOTS AND EAR PLUGS.
PLEASE BE AWARE OF THIS SYMBOL AS AN INDICATION TO CHECK THAT A PART IS LEVEL
OR PLUMB.
THIS SYMBOL IS AN INDICATION OF THE RECOMMENDED TORQUE EACH
BOLT SHOULD BE TIGHTENED TO. THIS VALUE WILL BE DEPENDENT ON
THE BOLT TYPE. PLEASE HAND TIGHTEN ALL BOLTS UNTIL YOU SEE THIS SYMBOL.
#MADEINBELFAST
5
9
8
11
10 12
13

x
8
x
4
ASSEMBLY
1
BOLT 1QTY BRANDING BOX ( 21-0047 ] AND 1QTY 1.2 BOX ( 21-0045 ) BETWEEN 2QTY UPRIGHTS
( 21-0058 ) WITH BOLT ASSEMBLY AS SHOWN. ENSURE LOGO ON BRANDING BOX IS FACING
FORWARD, LOGOS ON UPRIGHTS ARE FACING OUT AND ALL BOLTS FACING INWARDS.
10.0010
10.0023 x2
10.0028
10.0010
10.0023 x2
10.0028
#MADEINBELFAST

2
BOLT 1QTY MULTIGRIP ( 21-0165 ) TO 1QTY 1.2 BOX ( 21-0045 ) AND ATTACH BETWEEN 2QTY WESTSIDE
UPRIGHTS ( 21-0059 & 21-0060 ). CONNECT TO EXISTING ASSEMBLY USING 4QTY 0.4 BOX ( 21-0043 )
WITH BOLT ASSEMBLY AS SHOWN. ENSURE LOGO ON UPRIGHTS ARE FACING OUT
AND BOLTS ARE FACING INWARD.
#MADEINBELFAST
x
4
x
4
x
4
x
8
x
6
10.0010
10.0023 x2
10.0028
10.0010
10.0023 x2
10.0028
10.0010
10.0023 x2
10.0028
10.0010
10.0023 x2
10.0028
10.0010
10.0023 x2
10.0028

80
Nm
x 1
2
x26
3
TIGHTEN ALL BOLT ASSEMBLIES WITHIN THE CIRCLE TO SPECIFIED TORQUE. ENSURE
ALL UPRIGHTS ARE PLUMB. DRILL AND SECURE THE MIDDLE HOLE ON EACH UPRIGHT AS
SHOWN IN GUIDE. REMOVE ALL BOTTOM CROSSMEMBERS, DRILL AND SECURE REMAINING
HOLES ON UPRIGHTS AS SHOWN IN GUIDE. REATTACH THE BOTTOM CROSSMEMBERS.
#MADEINBELFAST
30
Nm
-DRILL 10MM HOLE
THROUGH FLOOR
COVERING, 90MM
DEEP USING PLATE
AS A GUIDE.
-VACUUM OUT THE
DUST.
-HAMMERSLEEVE
ANCHOR DOWN
INTO THE HOLE.
-TIGHTEN SLEEVE
ANCHOR TO
SPECIFIED TORQUE
USING 13MM
SPANNER.
DRILL
HOLE
VACUUM
HAMMER
IN BOLT
TIGHTEN
90MM

4
BOLT 8QTY UTILITY PEGS ( 21-0234 ) TO UPRIGHTS ( 21-0058 ) WITH BOLT ASSEMBLY AS
SHOWN TIGHTEN TO 80Nm.
#MADEINBELFAST
10.0010
10.0023 x2
10.0028

1:1 SCALE FASTENERS
FOR TERMS AND CONDITIONS VISIT OUR WEBSITE AT
www.blkboxfitness.com/pages/terms-conditions
GET IN TOUCH
TEL: [phone]
EMAIL: [e-mail]
DISCOVER MORE AT:
www.blkboxfitness.com
M10x80 SLEEVE ANCHOR
10-0031
M20x120 BOLT
NYLOCK NUT
10-0024
M10 FLAT WASHER
10-0019
#MADEINBELFAST