BLK BOX BLACKOUT User manual

OWNERS MANUAL & QUICK START GUIDE
BLACKOUT SQUAT STAND - 2.2M
NOTE : PLEASE READ ALL THE INSTRUCTIONS
CAREFULLY BEFORE ASSEMBLING THIS PRODUCT.
BLK BOX
21-0113-0E
#MADEINBELFAST
1112mm x 1320mm x 2266mm
2312mm x 2820mm x 3076mm
55kg
PRODUCT SPECIFICATION
PRODUCT WEIGHT
MAX USER WEIGHT
MAX USER
MAX TRAINING WEIGHT
DIMENSIONS
SAFE WORKING ZONE
-125kg
350kg
-
-
-
-
1
-

WARNING
SPIRIT LEVEL
10MM MASONRY
DRILL BIT
TOOLS REQUIRED
17MM SPANNER X2
13MM SPANNER
HAMMER
HAMMER DRILL VACUUM STEP LADDER
PARTS & ATTACHMENTS
No. Name SKU QTY
1 UPRGIHT 2.2M 21-0573 2
2 BASE FRAME - SA 21-0572 2
3 1.2 SINGLE BAR 21-0015 1
4 BACK CM 21-0602 1
5 FOOT PLATE 20-0412 2
6 BRACE PLATE 20-0472 4
7 M10X90 HEX HEAD BOLT 10-0008 20
8 M10 WAHER 10-0019 42
9 M10 NYLOCK NUT 10-0024 20
10 J-HOOK (PAIR) 16-0001 1
11 SLEEVE ANCHOR 10-0031 2
1
2
3
7
89
10
SERIOUS OR FATAL INJURIES MAY OCCUR FROM INCORRECTLY ASSEMBLED EQUIPMENT. ALWAYS ENSURE
BOLTS ARE TIGHTENED CORRECTLY AND ALL PARTS ARE LEVEL AND PLUMB. TO FURTHER REDUCE RISK OF
INJURIES OR DEATH PLEASE USE OUR SUGGESTED TOOLS AND PERSONAL PROTECTIVE EQUIPMENT (PPE).
WE SUGGEST THAT A MINIMUM OF THREE PEOPLE ARE INVOLVED IN THE ASSEMBLY OF THIS PRODUCT.
EACH PERSON SHOULD BE EQUIPPED WITH SAFETY GLASSES, STEEL TOE CAP BOOTS AND EAR PLUGS.
PLEASE BE AWARE OF THIS SYMBOL AS AN INDICATION TO CHECK THAT A PART IS LEVEL
OR PLUMB.
THIS SYMBOL IS AN INDICATION OF THE RECOMMENDED TORQUE EACH
BOLT SHOULD BE TIGHTENED TO. THIS VALUE WILL BE DEPENDENT ON
THE BOLT TYPE. PLEASE HAND TIGHTEN ALL BOLTS UNTIL YOU SEE THIS SYMBOL.
#MADEINBELFAST
4
5
6
11

ASSEMBLY
1
BOLT 1QTY BACK CM (21-0602) AND 2QTY BASE FRAME (21-0572) WITH BOLTS ASSEMBLY
AS SHOWN.
10.0008
10.0019 x2
10.0024
#MADEINBELFAST
2
INSERT 1QTY UPRIGHT (21-0573) INTO SLOT ON BASE FRAME (21-0572) AND ATTACH US-
ING 2QTY BRACE PLATE (20-0472) AND BOLT ASSEMBLIES AS SHOWN. ATTACH 1 QTY FOOT
PLATE (20-0412) USING BOLT ASSEMBLIES AS SHOWN. REPEAT FOR OPPOSITE SIDE.
10.0008
10.0019 x2
10.0024

3
PLACE 1QTY 1.2 SINGLE BAR (21-0015) AT PREFERRED HEIGHT ATTACH WITH BOLT ASSEM-
BLIES AS SHOWN.
FOLLOW GUIDE BELOW FOR FLOOR MOUNTING.
TIGHTEN ALL BOLT ASSEMBLIES TO 30NM.
#MADEINBELFAST
30
Nm
30
Nm
DRILL HOLE VACUUM
90MM
HAMMER IN
BOLT
TIGHTEN
-DRILL 10MM HOLE, 90MM DEEP
USING PLATE AS A GUIDE.
-VACUUM OUT THE DUST.
-HAMMER SLEEVE ANCHOR INTO
THE HOLE.
-TIGHTEN SLEEVE ANCHOR TO
SPECIFIED TORQUE
USING 13MM SPANNER.
SLEEVE ANCHOR BOLT FITTING