BluDot Superchoice Collection Quick start guide

Superchoice Collection
DESIGNED IN 2017
ASSEMBLY NOTES | REV 08
NEED A HAND?
Contact us at [email protected] or
844.425.8368 for assistance.
CONTOUR DU JOUR.
Uncomplicated storage for messy times. Beveled relief drawer pulls are set
off by a matte painted finish.

1 | 844.425.8368 SUPERCHOICE COLLECTION
8041
An�-�p Bracket
Case
*The number of feet and anti-tip hardware included may vary depending on the size of the case.
1QTY
8042
An�-�p Strap
PT. 1220
PT. 8041
4*
4*
QTY
QTY
PT. 1221
Foot
4*
6*
QTY
QTY
PT. 8042
2*QTY
Parts & Hardware

[e-mail] |2ASSEMBLY NOTES
Step 01
ATTACH THE FEET.
Attach adjustable feet as shown. After the feet have
been attached have a second person help lift and bring
the case upright to prevent damage to feet.
Note:Adjust the feet to make the case level before use.
Cases that are not level may have drawers and/or doors
that mis-align or rub against other components.
See last page in assembly instructions for adjustment
details if your drawers or doors are rubbing against
other components.

3 | 844.425.8368 SUPERCHOICE COLLECTION
8041
An�-�p Bracket
PT. 8041 x 2PT. 1221 x 4
Side Panel
1” lower than
case top
Align anti-tip brackets
with wall studs
Step 02
ATTACH ANTI-TIP BRACKETS TO THE WALL.
Install anti-tip brackets to wall stud 1-inch
below case top panel height.
Note:Smaller casegoods such as nightstands
may only include one set of anti-tip brackets.
In these instances,attach the anti-tip bracket
near the center.

[e-mail] |4ASSEMBLY NOTES
8041
An�-�p Bracket
PT. 8041 x 2PT. 1220 x 4
Top Panel
Back
Panel
Step 03
INSTALL ANTI-TIP BRACKETS TO CASE.
Brackets must be installed to top panel
of case. In order to prevent damage, it is
recommended that 3/32” pilot holes be
drilled prior to installation.

5 | 844.425.8368 SUPERCHOICE COLLECTION
PT. 8042 X 2
8042
An�-�p Strap
Step 04
SECURE THE CASE.
Install and tighten the straps prior to using the
product.

[e-mail] |6ASSEMBLY NOTES
TO REINSTALL THE DRAWER.
Lower drawer front into place and push closed.
Drawer Removal
TO REMOVE DRAWERS.
Extend the drawer completely. Squeeze both
locks on the underside of the drawer while
pulling the drawer out.

BLU DOT DESIGN & MANUFACTURING, INC. DESIGNED IN MINNEAPOLIS, MN
3
1
2
If door needs adjustment from
SIDE TO SIDE, Use Screw #1
If door needs adjustment from
FRONT TO BACK, Use Screw #2
If door needs adjustment from
TOP TO BOTTOM, Use Screw #3
Drawer Front
UP
DOWN
1
2
3
3
UP
DOWN
Additional Information
CLEAN
Clean with a slightly damp, soft cloth. To remove dirt and fingerprints, use a quality cleaner formulated
for wood furniture. Wipe completely dry with a soft cloth.
Adjusting Drawers and Doors
ADJUSTING DRAWER HEIGHT.
The drawer heights may be adjusted to prevent surfaces
from rubbing against each other. Press down on the blue
tab and rotate as shown to move the drawer up or down.
ADJUSTING DOORS.
Hinges work in pairs. If you adjust one hinge, chances are
you will have to adjust all the hinges.