Bosch B426 Operating instructions

Conettix Ethernet Communication Module
B426
en Installation and Operation Guide (UL)

Table of contents
1Safety 4
2Introduction 5
2.1 About documentation 5
2.2 Bosch Security Systems, Inc. product manufacturing dates 5
3System overview 6
3.1 Overview 8
3.2 Bus address settings 8
4Installation 10
4.1 Mount the module in the enclosure 10
4.2 Mount and wire the tamper switch (optional) 10
4.3 Wire to the control panel 10
5Configuration 13
5.1 Configure for SDI2 control panels 13
5.2 Configure for SDI or option bus control panels 13
5.2.1 Plug and Play configuration 13
5.2.2 Web-based configuration 13
5.3 Determine a module's hostname or IP address 14
5.3.1 Determine a module’s hostname 14
5.3.2 Use an SDI/SDI2 keypad or RPS to discover the IP address of a module 14
5.3.3 Use DHCP to look up the IP address of a network-connected module 14
5.3.4 Use AutoIP with a directly connected module 14
5.4 Use web-based configuration menus 16
5.5 Device Information (home) page 16
5.6 Change and save settings using the web 17
5.7 Basic Network Settings page 17
5.8 Advanced Network Settings page 20
5.9 Panel Address Settings page 21
5.10 Encryption and Security Settings page 22
5.11 Maintenance page 23
5.12 Factory Default page 25
5.13 Firmware Update page 25
5.14 Exiting the web-based configuration pages 26
6Maintenance and troubleshooting LEDs 27
6.1 Show the firmware version 28
7Specifications and certifications 29
7.1 Technical specifications 29
7.2 Certifications 30
Conettix Ethernet Communication
Module Table of Contents | en 3
Bosch Security Systems, Inc. Installation and Operation Guide (UL) 2013.08 | 02 | F.01U.281.208

Safety
ESD Precaution
Please note that the B426 board comes without any case/box and all components are exposed
for finger touches - therefore extra attention must be paid to ESD (electrostatic discharge)
precaution. Make sure there is no static interference when using the board. Appropriate ESD
protections must be taken and wearing electrostatic equipment is recommended, such as anti-
static wrist strap.
ESD damage can range from subtle performance degradation to complete device failure.
Precision integrated circuits may be more susceptible to damage because very small
parametric changes could cause the device not to meet its published specifications.
!
Warning!
Failure to follow these instructions can result in a failure to initiate alarm conditions. Bosch
Security Systems, Inc. is not responsible for improperly installed, tested, or maintained
devices. Follow these instructions to avoid personal injury and damage to the equipment.
Notice!
Inform the operator and the local authority having jurisdiction (AHJ) before installing the
module in an existing system.
Disconnect all power to the control panel before installing the module.
Before installing a B426, refer to Technical specifications, page 29.
1
4en | Safety Conettix Ethernet Communication
Module
2013.08 | 02 | F.01U.281.208 Installation and Operation Guide (UL) Bosch Security Systems, Inc.

Introduction
About documentation
Copyright
This document is the intellectual property of Bosch Security Systems, Inc. and is protected by
copyright. All rights reserved.
Trademarks
All hardware and software product names used in this document are likely to be registered
trademarks and must be treated accordingly.
Bosch Security Systems, Inc. product manufacturing dates
Use the serial number located on the product label and refer to the Bosch Security Systems,
Inc. web site at http://www.boschsecurity.com/datecodes/.
The following image shows an example of a product label and highlights where to find the
manufacturing date within the serial number.
2
2.1
2.2
Conettix Ethernet Communication
Module Introduction | en 5
Bosch Security Systems, Inc. Installation and Operation Guide (UL) 2013.08 | 02 | F.01U.281.208

System overview
!
Warning!
Failure to follow these instructions can result in a failure to initiate alarm conditions. Bosch
Security Systems, Inc. is not responsible for improperly installed, tested, or maintained
devices. Follow these instructions to avoid personal injury and damage to the equipment.
Notice!
Inform the operator and the local authority having jurisdiction (AHJ) before installing the
module in an existing system.
Disconnect all power to the control panel before installing the module.
Before installing a B426, refer to Technical specifications, page 29.
Use the B426 for bi-directional communication over an Ethernet network.
1
4
5
6
3
2
7
8
9
10
12
13
11
Figure 3.1: B426 system connections overview
3
6en | System overview Conettix Ethernet Communication
Module
2013.08 | 02 | F.01U.281.208 Installation and Operation Guide (UL) Bosch Security Systems, Inc.

Callout ᅳ Description Callout ᅳ Description
1 ᅳ Compatible Bosch control panel 8 ᅳ Ethernet network connection to the
Ethernet adapter (D6680/ITS-D6682/
ITS-D6686) (ITS-D6682 shown) Ethernet
Network Adapter
2 ᅳ Data bus connection between the control
panel and the module
9 ᅳ Conettix Ethernet Network Adapter
(ITS-D6682 shown)
3 ᅳ B426 10 ᅳ Connection from ITS-D6682 to the
COM4 Port on the Conettix D6600
Communications Receiver/Gateway
4 ᅳ Ethernet connection between module and
Ethernet network
11 ᅳ Conettix D6600 Communications
Receiver/Gateway
5 ᅳ Ethernet network, Local Area Network
(LAN), Metropolitan AreaNetwork (MAN), Wide
Area Network (WAN), or Internet
12 ᅳ Ethernet network connection
between the host computer Ethernet
network interface card (NIC) and the
Ethernet network
6 ᅳ Ethernet network connection to the D6100i
Communications Receiver (D6100i/D6100IPv6)
13 ᅳ Host PC running Remote
Programming Software, Automation, or
the Conettix D6200 Programming/
Administration Software
7 ᅳ Conettix D6100i Communications
Receiver/Gateway
Conettix Ethernet Communication
Module System overview | en 7
Bosch Security Systems, Inc. Installation and Operation Guide (UL) 2013.08 | 02 | F.01U.281.208

B426 module overview
1
4
5
7
9
6
TX
RX
R PWR
G B
Y A
B COM
MODE
8
TMPR
3
LINK
100 MB
2
Figure 3.2: B426 Conettix Ethernet Communication Module
Callout ᅳ Description
1 ᅳ Ethernet RJ-45 port
2 ᅳ Yellow LINK LED
3 ᅳ Green 100MB LED
4 ᅳ Data bus communication LEDs (TX and RX)
5 ᅳ Heartbeat LED
6 ᅳ Address switch
7 ᅳ Terminal strip (to control panel)
8 ᅳ Interconnect wiring connectors (to control panel or other compatible modules)
9 ᅳ Tamper switch connector
Overview
The B426 Conettix Ethernet Communication Module is a four-wire powered SDI, SDI2, or
option bus device that provides two-way communication with compatible control panels over
IPv6 or IPv4 Ethernet networks.
The B426 on-board switch determines the bus address of the device. Configuration of the
B426 is performed through the B426 configuration web pages. On SDI2 control panels,
configuration can also be done on the keypad or through Remote Programming Software
(RPS). The B426 Conettix Ethernet Communication Module is compatible with IPv6.
Bus address settings
The address switch determines the bus address for the B426 Conettix Ethernet
Communication Module. The control panel uses the address for communications. Use a
slotted screwdriver to set the address switch.
3.1
3.2
8en | System overview Conettix Ethernet Communication
Module
2013.08 | 02 | F.01U.281.208 Installation and Operation Guide (UL) Bosch Security Systems, Inc.

Notice!
The module reads the address switch setting only during power up. If you change the
switches after you apply power to the module, you must cycle the power to the module in
order for the new setting to be enabled.
The B426 address switch provides the value for the module's address. The figure below shows
the address switch setting for address 1. Refer to the table below for panel-specific settings.
Figure 3.3: Address switch set to address 1
Control panels Switch
position
B426 address Bus type Function
Web-based configuration
setting
0 Configurable Any Web-based configuration
GV4 Series, B5512/B4512/
B3512
1 1 SDI2 Automation, RPS, or Reporting
GV4 Series 2 2 SDI2 Automation, RPS, or Reporting
GV4 Series, GV3 Series, GV2
Series, G Series v6.3 or
higher
3 80 SDI Automation
GV4 Series, GV3 Series, GV2
Series, G Series v6.3 or
higher
4 88 SDI Reporting or RPS
GV4 Series, GV3 Series 5 92 SDI Reporting or RPS
DS7240V2, DS7220V2, Easy
Series V3+, AMAX 2000
6 134 Option Remote programming, Reporting
DS7400Xi 7 13 Option Remote programming, Reporting
DS7400Xi 8 14 Option Reporting
FPD-7024 9 250 Option Remote programming, Reporting
Table 3.1: B426 address switch settings
Notice!
You can use web browser configuration of the module's bus address setting only when the
switch is in the ’0’ position.
Conettix Ethernet Communication
Module System overview | en 9
Bosch Security Systems, Inc. Installation and Operation Guide (UL) 2013.08 | 02 | F.01U.281.208

Installation
After you set the address switch for the proper address, install the module in the enclosure
and then wire the module to the control panel and to the Ethernet connection.
Mount the module in the enclosure
Mount the B426 into the enclosure’s 3-hole mounting pattern using the supplied mounting
screws and mounting bracket.
You must mount the module in the control panel enclosure or in a UL listed enclosure (for
example, the D8103 Universal Enclosure).
All communicators shall be housed in tampered enclosures, compliant with the following
clauses within Standard CAN/ULC-S304-06: 5.2.6; 5.2.9; 5.2.10 and 5.2.15.
3
12
Figure 4.1: Mounting the module
Callout ᅳ Description
1 ᅳ B426 with mounting bracket installed
2 ᅳ Enclosure
3 ᅳ Mounting screws (3)
Mount and wire the tamper switch (optional)
You can connect an enclosure door tamper switch for one module in an enclosure.
Installing the optional tamper switch for use with a B426:
1. Mount the EZTS Cover and Wall Tamper Switch (P/N: F01U009269) into the enclosure’s
tamper switch mounting location. For complete instructions, refer to the Cover and Wall
Tamper Switch (ICP- EZTS) Installation Guide (P/N: F01U003734).
2. Plug the tamper switch wire onto the module’s tamper switch connector. For the tamper
switch connector location, refer to B426 module overview, page 8.
Wire to the control panel
When you wire a B426 to an SDI or SDI2 control panel, you can use either the module's
terminal strip labeled R, Y, G, B (PWR, A, B, COM) or the module's interconnect wiring
connectors (wire included). The figure below indicates the location of both the terminal strip
and the interconnect wiring connectors on the module.
4
4.1
4.2
4.3
10 en | Installation Conettix Ethernet Communication
Module
2013.08 | 02 | F.01U.281.208 Installation and Operation Guide (UL) Bosch Security Systems, Inc.