Broyhill A412002000 User manual

ASSEMBLY INSTRUCTIONS
ITEM#: A412002000
SKU# 810499956
BROYHILL ARBOR
Need help? We are here for you! 1(866)578.6569 24/7 • Toll Free

MAINTENANCE:
WHAT IS COVERED?
The limited warranty is extended to the original purchaser and applies to material and manufacturer’s defect provided
the item is maintained with care and used only for personal, residential purposes.
Warranty:6 Months
WARRANTY:
WARNINGS:
GENERAL BEST PRACTICES FOR ASSEMBLY:
• Please read and understand this entire manual before attempting to assemble or install the product.
• Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and
hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
• The assembled planters should be located at least 6 feet from any obstruction such as fence, garage, house,
overhanging branches, laundry lines or electrical wires.
• Some parts may contain sharp edges. Wear protective gloves if necessary, during assembly.
• Check all nuts and bolts periodically for tightness and, when required, tighten them again.
• Pay attention to the parts orientation
• Do not assemble the planters on sandy, muddy or loose soil, as stakes do not have enough anchorage in these types
of soil.
• Any assembly or maintenance of the product must be carried out by adults only.
• Please check your state and local regulations prior to purchasing. Some jurisdictions may require permits for installa-
tion and use. Some special procedures may be valid in your area.
• If any scratch paint, please touch up to prevent rusting
• For outdoor use only.
• Steel components for this planters are treated with rust inhibiting paint that protects it from rusting. However, due to
the nature of steel, surface oxidation (rusting) will occur if these protective coatings are scratched. This is not a defect
and thus not covered by the warranty.
• To minimize this condition, it is recommended to use care when assembling and handling the product to prevent
scratching the paint. Should any scratching or damage occur, it is recommended to cover the scratch immediately
with rust inhibiting paint (not included).
• Surface rust can also be easily removed with a very light application of regular cooking oil or WD-40. If surface
oxidation (rusting) occurs and if no measure is taken to prevent this, the oxidation may start dripping onto deck or
patio and caused damaging stains, which may be difficult to remove. This can be prevented if the above-mentioned
measures are taken to keep the product from oxidizing.
• Do not use bleach, acid, or other abrasive cleaners on the roof or frame parts.
• Keep instruction manual for future reference.
2/15

EXPLODED DRAWING
3/15

PARTS LIST
4/15
Label Part Number Description Qty Part Image
A P000601300 Top Beam 5
B P000400818 Long Beam 2
C P000400819 Short Beam 2
D P005000535 Support Bar 1 2
D1 P00500058801 Support Bar 2
E P005600074 Decoration 4
F P006300001 Screen 2
G P000200530 Post 1 2
J P000200571 Post 2 2
K P003900108 Front Panel 2
L P004000221 Back Panel 2
M P003800506 Side Panel 4
N P004700009 Bottom Frame 2
2

HARDWARE LIST
5/15
Label Part Number Description Qty Add Part Image
H1 H010010003 Bolt M6*15 32 4
H2 H010010010 Bolt M6*25 20 2
H3 H010010004 Bolt M6*35 10 1
H4 H010010026 Bolt M6*50 4 1
H5 H050030001 Flat washer
M6 66 7
HS H070010005 Stake ￠
6*230 4 0
HW H090010017 Wrench M6 1 0

HELPFUL HINTS
• Tools needed and not included
• Separating parts before starting
How many people are needed for the installation
Provided in hardware pack Provided
6/15

STEP 1
Assembled View:
Attached Screen (F) to Post 1(G) and
Post 2(J) with Bolt(H2) and Flat
washer(H5), tighten with Wrench(HW).
7/15
2x
2x
12x
2x
12x

STEP 2
Assembled View:
Attached Side Panel(M) to Back Panel
(L) with Bolt(H1) and Flat washer(H5),
tighten with Wrench(HW).
8/15
8x
2x 4x
8x
此面向下
此面向上

STEP 3
Assembled View:
Attached Side Panel(M) to Front Panel
(K) with Bolt(H1) and Flat washer(H5),
tighten with Wrench(HW).
9/15
8x
2x
8x

STEP 4
Assembled View:
Attached the assembled Screen (F/G/J) to
the assembled Planter (M/L/K) with
Bolt(H2) and Flat washer(H5), tighten
with Wrench(HW).
10/15
此面向下
8x
8x