Car Solutions QHI-XC90 U User manual

Installation Manual
Multimedia Interface for Volvo XC90
[email protected]
car-solutions.com
car-solutions.com

•Specification
Car compatibility: Volvo XC90, S90 2017
Components : Interface* 1ea, Sub board*1ea
Multimedia interface Input/output spec
Input : Analog RGB*1(Navigation), HDMI*1, A/V*2,
CVBS(Rear camera)*1,
Output : To LCD*1
Power spec
Input power : 8VDC ~ 18VDC
consumption : 5WATT
Switch input mode
External video sources skip function : able to control input
videos on and off via DIP switches.
Able to switch videos via the remote, button switch, and
original buttons.
Able to detect the rear view camera (back up camera) via
Lamp or CAN.
2
•Features
Control external videos sources (DVD, DTV) via Multi Media
Touch
Adjust external videos screen position
The improved Screen Display (User Friendly Interface)
Switch modes via OEM button
Supply power for rear view camera (Back up camera)
Assist your parking via Dynamic PAS(Parking Assistance
System), moving parking line according movement of
steering wheel
[email protected]
car-solutions.com
car-solutions.com

3
•Product Exterior
•Components
Power * 1ea LCD * 2ea
(HLCDCA0017)
LCD Extension * 1ea
(QCPASS0638)
AV * 1ea
(HAVCAB0056)
MULTI * 1ea
(HARETC0240)
RGB * 1ea
(HRGBCA0026)
BUTTON * 1ea
(HARETC0001)
IR * 1ea
(HIRCAB0002)
Remote * 1ea
(REMOTE0001)
REAR * 1ea
(HARETC0002)
[email protected]
car-solutions.com
car-solutions.com

* ON: DOWN / OFF: UP
Please make sure to disconnect the power cable
of interface and reconnect to apply dip switch
setting whenever changing DIP switch.
4
PIN FUNCTION Dip S/W SELECT
1 RGB
OFF : RGB Mode
ON : RGB Mode Skip
2 HDMI
OFF : HDMI Mode
ON : HDMI Mode Skip
3 AV1
OFF : AV1 Mode
ON : AV1 Mode Skip
4 AV2
OFF : AV2 Mode
ON : AV2 Mode Skip
5 Front Camera
OFF : Ext. Front Camera Mode
ON : OEM Front Camera Mode
6 No Use (OFF)
7 Rear Camera
OFF : OEM Rear Camera Mode
ON : Ext. Rear Camera Mode
8 No Use (OFF)
[email protected]
car-solutions.com
car-solutions.com

5
Key FUNCTION
POWER & PIP N/C
MENU Activating OSD menu
OK Making a selection, changing image display
▲Moving upward
▼Moving downward
◀
Moving leftward
(If you press this button 2 seconds long, you can access the
factory mode)
▶
Moving rightward
(If you press this button 2 seconds long, you can reset all the
data about user environment)
[email protected]
car-solutions.com
car-solutions.com

6
PARKING
PAS TYPE:
Select parking line type.
NOT USED: Do not use parking line
PAS ON: Use Flexible Parking Lines
PAS OFF: Use fixed parking line
PAS SETUP:
You can move the position of parking line.
REAR TYPE:
Choose rear camera recognition.
CAN: Detecting the rear view camera by CAN signal. (Installer must connect “CAN”
cable of the power cable to the “CAN” cable of the car)
LAMP: Detecting the rear view camera via “Grey Rear” wire. (Installer must connect
“Rear-C” cable of the power cable to the rear lamp of the car)
REAR SPLIT:
(RCAM ONLY, RCAM+Ori.CAM, RCAM+Ori.PDC)
IMAGE
H-POSITION/V-POSITION Setting
IMAGE
PARK
UTIL1
UTIL2
INFO
H-POSITION
V-POSITION
Menu of FACTORY
MENU to Return SEL to Select/Save
IMAGE
PARK
UTIL1
UTIL2
INFO
PAS TYPE
PAS SETUP
REAR TYPE
REAR SPLIT
Menu of FACTORY
MENU to Return SEL to Select/Save
[email protected]
car-solutions.com
car-solutions.com

7
UTIL1
NAVI MODEL:
Android, Car-play, Navigation Model Setting
AUDIO OUT:
Select audio channel transmitted through AUX
(Default/AV1/AV2)
FCAM TIME:
Front Camera Display Setting
FACTORY RESET:
Factory mode reset (YES/NO)
UTIL2
REMOTE CONTROL:
Able to control UI remote by touch (OFF/ON)
REMOTE TYPE:
Able to use remote control on DVD, DTV by
selecting “User” after IR memory registered
IR MEMORY:
Register IR memory of remote control for DTV,
DVD(AV1/AV2)
INFO
System version information
IMAGE
PARK
UTIL1
UTIL2
INFO
NAVI MODEL
AVOUT SELECT
FCAM TIME
FACTORY RESET
Menu of FACTORY
MENU to Return SEL to Select/Save
IMAGE
PARK
UTIL1
UTIL2
INFO
REMOTE CONTROL
REMOTE TYPE
IR MEMORY
Menu of FACTORY
MENU to Return SEL to Select/Save
IMAGE
PARK
UTIL1
UTIL2
INFO
<SYSTEM VERSION>
- MAIN : 201028
Menu of FACTORY
MENU to Return SEL to Select/Save
[email protected]
car-solutions.com
car-solutions.com

8
•OEM button
※ Press Home button to switch the mode
* Press the button twice :
Mode switch(RGB→HDMI1→A/V1→A/V2→F-CAM→OEM)
* Short press : Back to OEM
[email protected]
car-solutions.com
car-solutions.com

9
•Installation diagram
ACC
BUTTON1
BUTTON2
GND
CAN1-H
CAN1-L
CAM2-H
CAN2-L
HDMI
Device
RGB
NAVI BOX
A
U
D
I
O
(R)
O
U
T
A
U
D
I
O
(L)
O
U
T
F
C
A
M
A
U
D
I
O
(R)
IN
1
A
U
D
I
O
(L)
IN
1
R
C
A
M
V
I
D
E
O
IN
1
V
I
D
E
O
O
U
T
1
V
I
D
E
O
O
U
T
2
A
U
D
I
O
(R)
IN
2
A
U
D
I
O
(L)
IN
2
V
I
D
E
O
IN
2
A/V CABLE
R
C
A
M
S
A
F
E
R
E
A
R
V
1
I
R
V
2
I
R
R
E
M
O
T
E
T
O
G
G
L
E
12
V
S
E
L
F
C
A
M
12
V
MULTI CABLE
RGB Pin #7 is
UART-TX for UART
Touch
[email protected]
car-solutions.com
car-solutions.com

10
•CAN connection(GEAR, PAS)
※ The color of wires may vary
CAN High : this cable is connected to
CAN1-H(#3pin) of the supplied power
cable
CAN Low : this cable is connected to
CAN1-L(#4 pin) of the supplied power cable
※ Find OBD cable under the driver’s seat
•ADC connection to use OEM button
※ Find the cable behind the monitor
ADC(#11pin) : this cable is connected to
BUTTON1(#7pin) of the supplied power cable
6
12
11
[email protected]
car-solutions.com
car-solutions.com

11
•CAN connection(GEAR, PAS)
※ CAN wires are not located at OBD parts.
[email protected]
car-solutions.com
car-solutions.com

12
•LCD cable connection
Find OEM blue
cable on the back
side of the monitor
Remove the OEM
blue cable
Connect the
supplied LCD cable
to the same place.
1. Connect Blue OEM cable to LCD extension connector and the
supplied LCD cable is connected between LCD extension connector
and LVDS-IN of the interface
2. Also, the supplied LCD cable is connected between the monitor and
LVDS-out of the interface
OEM cable
Monitor
1
2
[email protected]
car-solutions.com
car-solutions.com

1. Ignition key should be taken off before starting installation, interface
power connection must be the last step in installation.
2. Power cable should be separated when connecting interface.
3. Should be no any electronic devices or magnetic pole around
installation place.
4. All steps of installation should be done by well-trained specialist.
5. Dismantling without manufacturer’s permission can not be guaranteed,
(No permission to break attached label on the board.)
6. Kindly check all parts are in the box, when receiving the product, if
anything missing, inform to the supplier or manufacturer.
7. According to our sales policy, any problems caused by user’s mistake,
careless can not be guaranteed.
13
[email protected]
car-solutions.com
car-solutions.com

14
Q. I cannot change mode
A. Check connection of Ground cable and IR Cable. Check LED lamp is on, if not
check connection of POWER cable.
Q. All I got on the screen is black.
A. Check second LED lamp of the interface is on, if not, check A/V sources
connected are working well. (Second lamp indicates AV sources connected works
well) Check interface connection has been done well.
Q. Displayed image color is not proper (too dark or unsuitable color)
A. Press ▶ button on the remote control for 2 seconds and check how it goes, if it
does not work, inform to manufacturer.
Q. I cannot watch the rear camera on the screen
A. Set the DIP switch #7 as state “ON”.
Q. Set mode not appear
A. Check DIP Switch.
Q. OEM image is not displayed.
A. Check interface’s LCD In/Out cable connection. If the status keeps on, inform to
manufacturer.
Q. Screen only displays white color.
A. Check LCD out cable is connected well, if this status keeps, inform to
manufacturer.
Q. If no image is shown on screen after connecting CAN wire with Park gear.
A. Go on the “FACTORY MODE”, check “UTIL-Rear Select”. If “LAMP”, change the
setting as “CAN” with the remote control. (* when connecting Rear-C wire of LAMP
power cable to Backup lights, Setting should be like this / CAN : if controlling rear
camera with CAN wire)
[email protected]
car-solutions.com
car-solutions.com