Cisco TelePresence SX20 Assembly instructions

78-20385-01 SX20 Quick Set Installation Sheet | 2011 DECEMBER | © 2011 Cisco Systems, Inc. All rights reserved.
Installing Cisco TelePresence SX20 Quick Set
A级声明 (A Class product declaration)
本产品为 A级ITE，在其使用说明，铭牌等显著位置中已包含如下内容的声明
(We declare here that the subject product is A class ITE product, and the
following statement is clearly marked in the user manual or nameplate):
声明所在位置 (Position of the Declaration):
 使用说明 User Manual
 铭牌 Nameplate
申请号 (Application No.)：
申请人 (Applicant):
型号 (Model Number)：
签字/盖章 Signature/Stamp:
日期 Date:
警告
此为 A级产品。在生活环境中，该产品可能会造成无线电干扰。在这种
情况下，可能需要用户对干扰采取切实可行的措施。
WARNING:
This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
SX20 Quick Set components
ySX20 Codec
yCamera options
A: PrecisionHD1080p12X
B: PrecisionHD1080p4XS2
yTable Mic 20 microphone
(1 default and 1 optional)
yRemote control and
four AAA batteries
yHDMI cable for monitor
(1 default and 1 optional)
yEthernet cable for LAN
yVGA to DVI-A cable
for PC connectivity
yCamera cable
yPower supply and
power cable
yCamera mounting bracket
In addition to the SX20 Quick Set you must provide a monitor or
projector, and a loudspeaker (external or built-in to the monitor) to
complete your video conferencing system.
User guides
User guides and compliance and safety information for this product,
is available at http://www.cisco.com/go/telepresence/docs.
Navigate to your product in the right pane; start by selecting
TelePresence Solutions Platform.
EMC Class A declaration
WARNING: This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be required to take
adequate measures.
Camera option A:
PrecisionHD1080p 12X
Snap on the lens hood to
prevent stray light from
disturbing your video
experience.
The camera snaps to the
magnets on the bracket.
Camera option B:
PrecisionHD1080p 4XS2
The camera is
fastened to the bracket
with a screw.
Tool: 4 mm Allen Key
(not provided).
Recommended room setup
The following should be regarded as
guidelines only. Try things out on-site
before fixing any mounting positions.
To learn more about optimizing your
office or meeting room for video
conferencing, please read the Video
conferencing room primer and
Guidelines for video conferencing
room acoustics documents available
on our web site.
Place the microphone(s) as
close to all meeting participants
as possible.
Place the camera just above
the monitor to enhance the
perceived eye contact.
If using the camera mounting
bracket, fasten it to the monitor
with the Velcro.
When placing the monitor and
camera, use the camera self
view function to make sure all
participants are captured by the
camera.
Aim for good illumination of a
person’s face to avoid shadows.
Also avoid direct light on the
monitor to prevent reflections.
The lower edge of the monitor
should be vertically aligned with
the table top.
Monitors larger than 55” should
be placed slightly lower.

78-20385-01 SX20 Quick Set Installation Sheet | 2011 DECEMBER | © 2011 Cisco Systems, Inc. All rights reserved.
Installing Cisco TelePresence SX20 Quick Set
Connecting the cables
Connect all cables as illustrated.
Caution: Make sure all units are switched off when connecting
or disconnecting devices.
If connecting an external loudspeaker, please take care
to use an active speaker (built-in amplifier).
Connect one or two Cisco Table Mic 20 microphones to
your codec.
Caution: Do not connect any other devices to the
microphone inputs.
Connect the codec to LAN/Ethernet.
Connect your primary display to the blue colored HDMI
socket.
With the dual display option, connect the second display
to the other HDMI output.
Connect your camera (option A or B) to the codec.
Connect a PC (video and audio) to be able to share
presentations (either locally or with remote participants).
Always use the provided Lite-On PA-1600-2A-LF
power supply (Input: 2 A, 100-240 V, 50-60 Hz;
Output: 5.0 A, 12.0 V).
2
4
1
3
5
Starting to use the system
Before you can make a call, you must configure the system as
described in the Getting Started Guide available on our web
site. See overleaf where to find the user guides online.
If the codec is not starting automatically, press the touch
button to switch it on. When the button lights steadily (this
may take a few minutes) the system is ready for configuration.
HDMI
Camera option A:
PrecisionHD1080p12X
Camera option B:
PrecisionHD1080p4XS2
2
1 4
67
3 5
6
7