Clarke Strong-Arm CS300D Instruction Manual

CAUTION: Do not keep the override keys inside the safe!
OPERATION & MAINTENANCE
INSTRUCTIONS
LS1014
DIGITAL SAFE
MODEL NO: CS300D
PART NO: 7710180

2
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
INTRODUCTION
Thank you for purchasing this CLARKE Digital Safe.
Before attempting to operate the safe, it is essential that you read this manual
thoroughly and carefully follow all instructions given. In doing so you can look forward to
the safe giving you long and satisfactory service.
GUARANTEE
This CLARKE product is guaranteed against faulty manufacture for a period of 12 months
from the date of purchase. Please keep your receipt as proof of purchase.
This guarantee is invalid if the product is found to have been abused or tampered with
in any way, or not used for the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product can be
returned to us without prior permission.
This guarantee does not effect your statutory rights.
SPECIFICATION
REPLACEMENT OVERRIDE KEY
A small label is located on the front of each safe with a key number. The number will
start with either the letter "J" or "G" followed by several digits. This number must be
registered with us in the event you require a replacement key.
Please complete the registration form at the back of this manual and send it to the
address stated with the form. If you fail to register the safe we will not be able to provide
you with a replacement key.
We recommend that in addition to sending the completed form you remove the label
from the safe and fix it to the space below. Please retain this document for future
reference.
Fix or record the key number here
Dimensions (DxWxH) 215 x 310 x 200 mm
Weight 6.7 kg
Batteries 4 x AA (1.5V) batteries
Volume 8.55 L
Number of keys supplied 2

3
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [email protected]
BEFORE USE
OPENING THE SAFE FOR THE FIRST TIME
1. Remove the small plastic cover
(B) on the front panel.
2. Insert the override key into the key
hole and turn it counterclockwise,
at the same time, turn the
doorknob (A) clockwise direction
to open the safe.
NOTE: Never keep the override keys
inside the safe itself.
3. Replce the small plastic cover (B) onto the front panel.
INSTALLING THE SAFE
The safe should be secured vertically to a
wall, cubord shelf or to the floor using the
expansion bolts (supplied).
• There are holes (8 mm) on the
rear and bottom of the safe for
securing to a wall or the floor.
INSTALLING THE BATTERIES
The safe requires 4 x size “AA” (1.5V)
batteries.
1. Open the safe.
2. Remove the battery cover plate
on the back of the door and
install the batteries.
3. Ensure the batteries are fitted with
the correct polarity.
4. Use of alkaline batteries is
recommended.

4
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
PROGRAMMING THE CODE
1. With the safe door open and the batteries installed.
2. Press and release the red button
on side of the lock housing.
• you will hear two beeps.
• The yellow light will be on at the
same time.
3. Enter the code you want to use
(3-8 digits) as a combination.
4. Confirm within 15 seconds by
pressing the letter “A” or “B”.
• The safe “bleeps” twice and the yellow light will go off, your personal
code is now set.
5. Test the safe using the new combination immediately.USING YOUR SAFE
TO OPEN THE SAFE
1. Enter your personal code followed by the letter “A” or “B”.
• you will hear a beep and the green light on the front of the safe will light
up.
2. Turn the doorknob in a clockwise direction to open the door within 5
seconds.
• If you, or an intruder uses the incorrect group of numbers, it will not open,
if the incorrect combination is used 3 times consecutively, you must wait
for 20 seconds before trying again.
• If the incorrect combination is selected a further 3 times, you must wait
approximately 5 minutes before trying again.
BATTERY REPLACEMENT WARNING
If the batteries are low, the red light (in the middle of the number panel) will illuminate.
MANUAL OVERRIDE
• See “Opening the safe for the first time” on page 3.

5
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [email protected]
DECLARATION OF CONFORMITY

7
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [email protected]
IMPORTANT
In order to be able to obtain a replacement key.
Please detatch and complete this safe registration
form (see reverse), Then return it to:
Clarke International
Product Registration Department
Shrubland Road
London
E10 7RB

8
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]